Psiber Data Systems PingerPro 70 Bedienungsanleitung

Psiber Data Systems Revision 2.01

USER GUIDE

PingerPro

Model 70/71/75/76

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com

Psiber Data Systems Revision 2.01

PingerPro User Guide

cannot be reproduced in any form without the prior written permission of Psiber Data Systems Inc. No patent liability is

Notice

Every effort was made to ensure that the information in this document was accurate at the time of printing. However,

information is subject to change without notice, and Psiber DataSystems reserves the right to provide an addendum to

this document with information not available at the time that this document was created.

PSIBER DATA SYSTEMS INC. PROVIDE NO WARRANTY WITH REGARD TO THIS MANUAL OR ANY OTHER

INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIM ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO ANY OF THE

FOREGOING. PSIBER ASSUMES NO LIABILITY FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY

FROM ANY TECHNICAL OR TYPOGRAPHICAL ERRORS OR OMISSIONS CONTAINED HEREIN OR FOR

DISCREPANCIES BETWEEN THE PRODUCT AND THE MANUAL. IN NO EVENT SHALL PSIBER BE LIABLE FOR

ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, OR EXEMPLARY DAMAGES, WHETHER BASED ON TORT,

CONTRACT OR OTHERWISE ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL OR ANYOTHER

INFORMATION CONTAINED HEREIN OR THE USE THEREOF.

Trademarks

The Psiber Logo, Psiber and PingerPro are trademarks of Psiber Data Systems Inc. All other brands and

product names are trademarks or registered trademarks of their respective companies.

Psiber Data Systems Revision 2.01

PingerPro User Guide

Introduction

Thousands of network professionals have relied on Psiber test tools for installing, troubleshooting and

maintaining complex, and high performance networks. The PingerPro’s extensive feature set makes it even

easier for managers and technicians to meet the growing challenges of cable and network management.

The PingerPro brings a new level of connectivity testing with: fault location, Gigabit Ethernet capability,

advanced IPv6 support, Logical Link Data Protocol (LLDP/CDP) and other powerful features that you will

use every day. As a result, the PingerPro is the complete high performance first-response tool designed to

solve your most frequent network problems. Whether installing new network drops or devices, monitoring

performance, or troubleshooting problems, the PingerPro quickly provides the answers you need.

The PingerPro 71/76 has added PoE Testing, enhanced length testing, and wiremap terminator detection.

The PingerPro touch screen interface lets you select discrete tests, or configure a complete Auto Test that

provides critical link information; conduct network connectivity tests and provide switch port information in

seconds. Document your test results with a few keystrokes to prove the job’s done right. The rechargeable

battery pack and rugged weather resistant design lets you test anywhere. The PingerPro is always available

and always ready to:

•Monitor network health

•Manage network changes

•Identify cable and network problems

•Optimize network performance.

Kit Content

Psiber Data Systems Revision 2.01

PingerPro User Guide

Physical

Specifications:

Dimensions: 6.5 in. x 4.0 in. x 2.8 in. (165 mm x 102 mm x 71 mm)

Weight: 13.2 oz.; 387 grams

Power Adaptor: 110/240 VAC

Graphics Display: 320 x 240 RGB

Interface: Color Touch Screen

Power: Li-Ion Battery Pack

Operating Temp: 32°F to 122°F / 0°C to 50°C

Storage Temp: 14°F to 131°F / -10°C to 55°C

Power

Button

Display

/Touch

screen

Strap

Connector

Stand

Clips

for

cables

Speaker

Hinged Hood to protect USB and

RJ-45 connectors. (Also SFP

Connector on the PingerPro75/76)

Psiber Data Systems Revision 2.01

PingerPro User Guide

Preparing the Unit

The PingerPro is portable and can be hand held or placed on a surface large enough for stable use. The

PingerPro is designed to withstand the rigors of everyday use and travel. However, to keep your tester in

prime operating condition, please observe the following precautions to further reduce the risk of personal

injury or damage to the tester.

▪Never apply heavy pressure to the tester, especially on or around the display area. Excessive

pressure or impact can damage components or otherwise cause the tester to malfunction.

▪Do not submerge, float or allow liquids to spill into or onto the tester.

▪Do not use excessive force while connecting or disconnecting cables or peripherals.

▪Use the supplied strap to prevent accidentally dropping the tester.

▪Never use sharp objects on the display/touch screen area. Use only the supplied stylus.

Protect the PingerPro from; dust, moisture, direct sunlight, liquids and corrosive materials. Equipment that

generates a strong electromagnetic field, rapid changes in temperature or humidity, extreme heat or cold

may also damage your tester. Operate the tester within the specified temperature range.

Battery Use:

The tester contains a rechargeable battery pack which comes charged from the factory for quick use. The

external USB adapter provides power to the tester and charges the battery pack from an AC outlet or

computer.

The battery pack can be charged while the tester is on or off. Charging time is reduced if the tester is turned

off. With the tester turned on, the battery symbol on the display provides the charge status of the battery

pack.

Caution:

To avoid electric shock, never modify, forcibly bend, damage, apply heat to or place heavy objects on top of

the power cord. If the power cable becomes damaged or the plug overheats, discontinue use.

Never remove the power plug from the outlet with wet hands.

Using the wrong AC adapter could damage your tester. Psiber assumes no liability for damage in such cases.

Never pull directly on the power cable to unplug it. Hold the power plug when removing the cable from the

outlet.

Psiber Data Systems Revision 2.01

PingerPro User Guide

Getting Started

Turn on the PingerPro by pressing the power button until the screen lights up, and then release the button.

The unit displays the welcome screen for approximately 10 seconds and then the Home Screen

automatically displays.

Copper Home Screen Fiber Home Screen

The Home Screen has Auto Test, Ping, Cable Test, Setup and Help Buttons.

•Auto Test tests the network with configured parameters selected from the Setup screen.

•Ping is a quick but powerful test that, while in factory default setting, sends a Ping from the tester

to the Gateway from any part of the network. The Ping test can be quickly changed to user

configured profiles to Ping other devices.

•The Cable Test tests the physical copper portion of the network by measuring the length of the

cable to a short or open, performing a wiremap analysis for incorrect wire connection, sending a

tone for traceability or sending a signal to blink the switch port specific LED.

•The Fiber Test displays the power detected from the device attached to the fiber SFP port.

•Setup allows the user to customize settings for the Auto Test and the Ping test to test specific

network parameters.

•The Help button displays step-by-step instructions on how to use the PingerPro and displays the

quick start guide.

Psiber Data Systems Revision 2.01

PingerPro User Guide

Setup

Select the SETUP button from the Home Screen. The available configurable categories are displayed on

the screen. Select a category to expand the button. When completed with any setup configuration, select

the Save button and then the Psiber button to return to the Home Screen.

Home Screen Main Setup Screen Main Setup Screen 2

Profiles

Select the Profile button to show a listing of all the profile names. There are 11 customizable profiles and

one Factory Default. The Factory Default profile cannot be changed.

Select a customizable profile by selecting the gray box to the left of an unassigned profile. A dialog pop-up

screen will be displayed. Select Set To Current to duplicate the parameters from the currently selected

profile. In this case, it will duplicate the Factory Default configurations. Select Set To Default to duplicate

the parameters of the Factory Default configuration. Select Cancel to return to the Profile Screen without

any changes.

Profile Screen Dialog Profile Box

Psiber Data Systems Revision 2.01

PingerPro User Guide

The User Profile 1 is now highlighted green and ready to be used for Auto Test. To edit newly created

profiles, select the User Profile 1 green checked box again.

Profile Screen Profile 2 Screen

A dialogue box will be displayed. Clear will delete the selected profile and return it to the unassigned state.

Select the Rename gray button to display a screen with an alphanumeric keyboard.

Enter any profile name with up to 20 characters. Select OK for the name to be saved and to return to the

Profile screen where the new name is displayed and highlighted.

Profile Dialog Box Full Keyboard Profile Screen

Psiber Data Systems Revision 2.01

PingerPro User Guide

Select the Profile button with the < arrow to return to the Main Setup Screen or select the Link button to

continue to the Link Setup Screen.

Setup Profile Screen Main Setup Screen

Link

Select the Link Button from the Main Setup Screen. The Speed parameter choices are Auto-negotiate or

Fixed speed/duplex. Auto selects all five speed/duplex modes; 10H, 10F, 100H, 100F or 1000F. In Fixed,

only ONE speed/duplex can be selected. Select the Save button to save the configuration.

Setup Copper Link Screen Setup Fiber Link Screen SFP Module Details Dialog Box

The Interface setting appears in the PingerPro 75/76 where there is an option to test either Copper or

Fiber cable. Once Fiber is selected, the SFP details and capabilities are displayed. Select the SFP Module

Detail button to show all the details of the connected SFP. Select OK to return to the Link Screen.

Psiber Data Systems Revision 2.01

PingerPro User Guide

Select the Varrow button to display the Link Timeout Setting. The Link Timeout is the amount of time the

PingerPro waits to establish a link. Select the Timeout button to display a numerical keyboard. After

entering a valid number, select OK to return to the Ping screen. Select the Save button to save the timeout

setting.

Setup Link Screen Setup Link Timeout Screen Numerical Keyboard

Select the Link button with the < arrow to return to the Main Setup Screen or select the IP Address button

to continue to the IP Address Setup Screen.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Psiber Data Systems Messgerät Handbücher

Psiber Data Systems

Psiber Data Systems NetXpert 1400 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung