PULOX MD100B Benutzerhandbuch
Quick Operation Guide
V1.0B1
1. Inserting Batteries
Fig.1
Open the battery cover
Fig.2
Insert two AAA batteries in the right polarity, and close the battery
cover.
Note: Do not insert batteries with their polarities reversed!
2. Power on and measurement
1. Palm Measurement
Fig.3
Press the / button to power on the monitor.
Fig.4
Press the “START”button to enter preparing stage.
Fig.5 Fig.6
During the preparing stage, hold the electrode with your hands
as shown the above two pictures.
Note: Please make your hands contact electrode of monitor
fully for a high quality ECG results.
Fig.7
After finishing preparing stage, the ECG measurement begins
and will takes 30 seconds for a measurement under Easy
mode. Refer to fig.7 for measurement interface.
Fig.8
Under Easy mode, the monitor will analyse the measurement
result after finishing measurement, refer to Fig.8. And save
the measurement results in 8 seconds.
2. Chest Measurement
If palm measurement is not ideal, please adopt chest
measurement. Hold the unit with right hand and place the
electrode against left chest on bare skin about 5cm bellow left
nipple
.
Fig.9
3. Cable Measurement
For higher quality ECG measurement, it is recommended to
apply cable cable measurement.
The correct connection steps are as follows:
1. Place the electrode slices on your body as indicated
as fig. 10.
2. And then connect the cable and the unit effectively
through the lead port.
The position for placing the cable electrode is shown in
Picture.
Fig.10
AHA:
White（right arm RA）electrode —put it under the
clavicle ,next to the right shoulder.
Black （left arm LA）electrode —put it under the
clavicle ,next to the left shoulder.
Red（left leg LL）electrode —put it at the left of the
underbelly.
IEC:
Red （right arm R ）electrode —put it under the
clavicle ,next to the right shoulder.
Yellow （left arm L ）electrode —put it under the
clavicle ,next to the left shoulder.
Green（left leg F）electrode —put it at the left of the
underbelly.
The connection with ECG lead cable
Make sure that deeply insert the ECG cable connector
with mild force.
When the measurement is failed，please check the
placement of electrode slices or the connection of the
unit and lead cable.
Wrong Operation Methods:
A. Connect wrong cable mount;
B. Electrodes contact wrong position of the body.
Caution!
Do not expose the unit to static electricity. Always disperse
any static electricity from your body before handling the unit.
Do not take measurements in a moving vehicle.
Do not use a cellular phone near the unit.
The chest electrode will be impeded by excessive body hair,
regularly remove hair at the electrode contact area.
Andere PULOX Medizinische Geräte Handbücher
PULOX
PULOX PO-100 Bedienungsanleitung
PULOX
PULOX PO-900 Bedienungsanleitung
PULOX
PULOX PO-250 Bedienungsanleitung
PULOX
PULOX PO-210B Bedienungsanleitung
PULOX
PULOX PO-200A Bedienungsanleitung
PULOX
PULOX PO-235 Bedienungsanleitung
PULOX
PULOX PO-220B Bedienungsanleitung
PULOX
PULOX PO-230 Bedienungsanleitung
PULOX
PULOX PO-200 Bedienungsanleitung
PULOX
PULOX Checkme O2 Bedienungsanleitung
Beliebte Medizinische Geräte Handbücher anderer Marken
TekTone
TekTone Tek-CARE160 Bedienungsanleitung
NeuroMetrix
NeuroMetrix Quell 2.0 Bedienungsanleitung
AMT
AMT XLR8 Bedienungsanleitung
Medipost-Nutristoma
Medipost-Nutristoma MD300K2 Bedienungsanleitung
EDAN
EDAN SONOTRAX Pro Bedienungsanleitung
Restorative Therapies
Restorative Therapies RT300 Bedienungsanleitung
