Pyle PLCAPE500 Bedienungsanleitung

        

                

         





Model: PLCAPE500

50F Hybrid Super Cap (carbon and eletroniccapacitor)

With Blue Digital Voltage Display

Capacitance .................................……...... 50,000,000 micro farad (50

Farad)

Working Voltage ...............................…….….. 16DC

Surge Voltage .......................................……… 18DC

E.S.R. (Equivalent Series Resistance)------ 0.0015 ohm @120hz/ 25°C

Capacitance Tolerance------------------------ ± 10%

a) 3 digits hi-end blue light display DC voltage meter that can measure

0.1 DCV range.

b) Reverse pole connecting PCB buzz warning function. If the capacitor is

connected incorrectly by reversing the positive and negative wires

during the installation process the PCB will issue a 45 second noise to

warn you.

c) Hi-end platinum plated 100% brass solid parts and chrome plated metal

cover

d) Over voltage limit and low battery voltage limit warning. When the

system voltage peeks over 17.5 DCV or LESS than 10 DCV. The

buzzer on the PCB will issue an audible noise warning.

e) Multiple small capacitance capacitors linked to provide the lowest

inner E.S.R. and largest moment discharge power.

DETAILED FEATURES:







                 

                                  

                  





You must first attach the mounting tabs to the capacitor before mounting

it. Use the supplied hardware shown in the picture to the right. Notice the

small mounting screw hole in the capacitor chassis.

CHARGING THE CAPACITOR AND WIRING:

The capacitor must be charged before connecting the Power and Ground

cables to the capacitor. Failure to charge the capacitor will result in a

large spark generated from the rapid inflow ofcurrent.

To Charge the capacitor:

1. Make Capacitor positive terminal connections with amplifier and

tighten the bolt. Do not over-tighten the bolts!

Caution: Stripped terminals are not covered under the capacitor’s

warranty.

2. Connect the ground cable with battery, amplifier, then refer to the

attached drawing.

3. Place the supplied charging bulb or resistor between the positive

terminal of the capacitor and the battery’s positive terminal. Do this

for 30 seconds or until the charging bulb goes out.

Caution: The charging bulb will get hot!

4. Immediately after the charging process, take out the charging bulb

from the connecting wire. And connect the positive cable of the

battery directly to the positive terminal on the capacitor.







               

                              

                









WHEN YOU WANT TO MOVE THE CAPACITOR FROM

ORIGINAL INSTALLED CAR AUDIO SYSTEM, YOU MUST FIRST

FOLLOW DISCHARGING PROCESS AFTER TAKING OUT THE

CAPACITOR FROM THE CAR AUDIO SYSTEM.

To Discharge the capacitor: With battery power disconnected, place the

light bulb or resistor across the capacitor’s positive and negative terminals

until light goes out or for three minutes if using a resistor.







              

                            

                     ! 

      !       ! 

      !  





            "

            "            "

            " 

One Year Warranty from the date of purchase.



    

        

     ##

####

##





  

           

          

           



Inhaltsverzeichnis

Andere Pyle Autozubehör Handbücher

Pyle

Pyle PLCMDVR 42 Bedienungsanleitung

Pyle

Pyle PLCMDVR72 Bedienungsanleitung

Pyle

Pyle BlueTech PBT70R Bedienungsanleitung

Pyle

Pyle PIFMDK6 Bedienungsanleitung

Pyle

Pyle PLDCP3 Bedienungsanleitung

Pyle

Pyle PLRD146 Bedienungsanleitung

Pyle

Pyle PLCAPE30 Bedienungsanleitung

Pyle

Pyle PLDCP25 Bedienungsanleitung

Pyle

Pyle PLCMDVR 8 Bedienungsanleitung

Pyle

Pyle PBT99 Bedienungsanleitung

Pyle

Pyle PLCM7500 Bedienungsanleitung

Pyle

Pyle PLDCP50 Bedienungsanleitung

Pyle

Pyle PLCMRV8B Black Bedienungsanleitung

Pyle

Pyle PLCPBT25 Bedienungsanleitung

Pyle

Pyle PHUD19 Bedienungsanleitung

Pyle

Pyle PBT96 Bedienungsanleitung

Pyle

Pyle WatchDog PLPSE3 Bedienungsanleitung

Pyle

Pyle PLCM4235 Bedienungsanleitung

Pyle

Pyle PLCAPE24 Bedienungsanleitung

Pyle

Pyle PLD94BK Bedienungsanleitung

Pyle

Pyle PLDCP1.2KIT Produktinformationsblatt

Pyle

Pyle PLCM2720 Bedienungsanleitung

Pyle

Pyle PLCM9200 Bedienungsanleitung

Pyle

Pyle PLCAPKT12 Produktinformationsblatt

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung