Pyramid Ac receiver Bedienungsanleitung

Please read this manual before installing your receiver

Pyramid AC Receiver

Installation Manual

Page 2

Pyramid AC Receiver Installation Manual

IMPORTANT

The first few pages of these instructions contain important information on safety and product

conformity. Please read, and ensure that you understand this information before continuing.

Page 3

Installation Manual Pyramid AC Receiver

CONTENTS

Product Safety ........................................................................................................................................................................................... 4

Electromagnetic Compatibility (EMC) .................................................................................................................................................. 4

Manufacturer s Declaration of Conformance .................................................................................................................................... 4

Unpacking ................................................................................................................................................................................................... 4

Barcoding ................................................................................................................................................................................................... 4

The AC Receiver .......................................................................................................................................................................................... 5

PCB Layout ................................................................................................................................................................................................... 6

PCB Power Connections .............................................................................................................................................................................. 7

Connecting the Preset Fee back Potentiometers ........................................................................................................................................ 7

Connecting the Lens Drive Outputs ............................................................................................................................................................. 8

Connecting the Pan/Tilt Hea an Auxiliaries .............................................................................................................................................. 8

Connecting the Pan/Tilt Hea an Auxiliaries Power Source ...................................................................................................................... 9

Anti-Tamper Connections ............................................................................................................................................................................. 9

Vi eo Connections ....................................................................................................................................................................................... 9

Fitting Network Car s ................................................................................................................................................................................. 10

PY-FTT, PY-485 an PY-422 Network Car s ............................................................................................................................................ 11

PY-COM Network Car s ............................................................................................................................................................................ 12

Fibre-Optic Network Car s ........................................................................................................................................................................ 12

Power Supply Connections ....................................................................................................................................................................... 13

A ressing a Receiver with the Pyrami 2 Keyboar .............................................................................................................................. 14

A ressing a Receiver with the Mk1 Keyboar ....................................................................................................................................... 15

Setting Receiver Configuration with the Pyrami 2 Keyboar .................................................................................................................. 16

Setting Receiver Configuration with the Mk1 Keyboar ........................................................................................................................... 17

Receiver Programming ............................................................................................................................................................................... 17

Testing ........................................................................................................................................................................................................ 18

Replacing the Li ........................................................................................................................................................................................ 18

Changing the Fuse ..................................................................................................................................................................................... 18

Specifications ............................................................................................................................................................................................. 19

Page 4

Pyramid AC Receiver Installation Manual

PRODUCT SAFETY

WARNING

 Please follow these instructions as you install the equipment and keep them for future use.

 Installation is only to be carried out by competent qualified and experienced personnel in accordance with the

country of installations National Wiring Regulations. Failure to do so can result in injury or death by electric shock.

 Use a class 2 isolated power supply for the 12V DC.

 The module is susceptible to damage from Electrostatic Discharge (ESD). Take normal ESD precautions when

handling your network card. ESD prevention kits are available from most electronics distributors.

 Do not exceed the voltage and temperature limits given in the specification.

 Switch off the power before fitting a network card.

 If you have any problems contact Baxall Limited.

ELECTROMAGNETIC COMPATIBILITY (EMC)

CAUTION

 This is a Class A product. In a domestic environment this product may cause radio interference in which case the

user may be required to take adequate measures.

 This product is intended for use in general purpose CCTV applications in a residential commercial or light

industrial EMC environment. Refer to Baxall Limited before using the product in medical and/or intrinsically safe

applications or in an industrial EMC environment.

 If you are using the PCB version of this product in a way other than correctly installed in the Pyramid system

weatherproof boxes then it is your responsibility to meet EMC requirements.

 The product must be installed in accordance with good installation practice for EMC to enable the product to

function as intended and to prevent EMC problems.

 Contact Baxall Technical Support to obtain a specification defining the acceptable levels of product degradation

with regard to EMC immunity.

MANUFACTURER S DECLARATION OF CONFORMANCE

CAUTION

The declaration of conformance applies only to the boxed version and PCBs which are correctly installed in our

Pyramid system weatherproof box.

The manufacturer declares that the equipment supplied with this manual is compliant with the essential protection

requirements of the EMC directive 89/336 and the Low Volta e Directive LVD 73/23 EEC. Conformin to the requirements

of standards EN55022 for emissions, IEC801 parts 2, 3 and 4 for immunity and BS415 superseded by EN60950 for

Electrical Equipment safety.

UNPACKING

Keep your packa in for use if your AC receiver is stored for an extended period or needs to be returned for any reason.

The packa in should contain:-

 An AC Receiver

 An A4 Module Description Sheet (for installation details)

 These instructions

 Two identical barcodes

Check the product code on the serial number label. If you have an incorrect item or it is dama ed then inform the

suppliers and carriers immediately. If this is the case, do not attempt to use the equipment.

BARCODING

The AC receiver is supplied with two identical barcodes. Remove one and affix it to the module description sheet, remove

the other and affix it to the module.

The barcode ives the unique 48-bit neuron ID to the module. This neuron ID is also stored inside the module and will

be transmitted onto the network whenever the PCB service pin is pressed. Before installation, make a careful note on

your module description sheet of all your installation details and the proposed location of the module. Then durin

subsequent installation usin the Windows installation tool the neuron ID can be entered.

We recommend that durin a system installation you store the module description sheets in a rin -bound file, and keep

them for reference after the installation is complete.

Page 5

Installation Manual Pyramid AC Receiver

THE AC RECEIVER

The Pyramid AC Receiver is a fixed speed pan and tilt control receiver that can be connected to any camera within the

Pyramid system that has an AC Pan/Tilt head. The receiver is easy to install, and a service pin and test button are included

to aid the installation process. Once it has been fitted, the receiver will drive the pan, tilt, zoom and focus functions of a

Pan/Tilt head, and it can also drive auxiliary equipment (wipers, li hts etc.) throu h the four auxiliary relays on the receiver

PCB.

The AC receiver can be pro rammed remotely with privacy zones, limit stops, random patrols, and up to 128 presets. It

also contains a video amplifier, with ain and hi h-frequency lift. This can improve video transmission over lon er cable

runs.

MAIN PCB

FILTER

BOARD

EXTERNAL

TERMINAL

BLOCK

FACTORY

FITTED

12V DC PSU

(

UNDER PCB)

METAL

BASEPLATE

WEATHERPROOF

BOX

Figure 1 - AC Receiver Layout (Weatherproof Box Variants)

There are six variants of the AC receiver, which can be split into two roupsthe three variants that are supplied in a

weatherproof box (PY-ACW-) and the three variants that are supplied as a PCB only (PY-ACB-). In each of these two

roups, the difference between the three variants is based on the network speed and the type of network card fitted.

The -L variants (PY-ACW-L and PY-ACB-L) run on a low speed (9.8k b.p.s.) RS485 network while the -HR variants (PY-

ACW-HR and PY-ACB-HR) run on a hi h speed (78k b.p.s.) RS485 network. Both the -L and -HR variants are fitted with

a PY-COM network carda combined personality network card which can be confi ured by means of dip switches for use

in RS485 or RS422 networks. By default, the switches are set so that the card operates in RS485 protocol, but the card

protocol can be easily chan ed usin the switch settin s. For more details on the PY-COM network card, see pa e 12.

The -H variants (PY-ACW-H and PY-ACB-H) are fitted with a PY-FTT network card and run on a hi h speed (78k b.p.s.)

FTT10 network. For more details on the PY-FTT network card, see pa e 11.

Page 6

Pyramid AC Receiver Installation Manual

PCB LAYOUT

Shown below are the locations of the connectors, switches and LEDs on the AC receiver PCB.

CON4

CON1

CON6

CON3

CON2 TEST

BUTTON

10A

FUSE

SERVICE

PIN LED

LED1

ANTI-TAMPER

SWITCH

VIDEO

OUT

CON5

LIVE

EUTRAL

IRIS -

FOCUS

5V +

TILT FB

PAN FB

FOCUS F

ZOOM FB

GND

ZOOM -

IRIS +

FOCUS

ZOOM +

DOWN

LEFT

RIGHT

AUX 1

AUX 2

AUX 3

AUX 4

Figure 2 - AC Receiver PCB

Page 7

Installation Manual Pyramid AC Receiver

PCB POWER CONNECTIONS

CON1 is used for PCB power connection. This power controls the switchin of the relays, the video ain and lift and the

lens functions. The AC power for the Pan/Tilt head and auxiliaries is connected separately to CON5.

The PCB requires a +12V DC, 1A class 2 power supply. The necessary connections have already been made on the

boxed variants, includin a roundin wire which is connected from the ne ative terminal of CON1 to the external terminal

block (Fi ure 3). On PCB versions, connect the 12V DC as shown in Fi ure 3.

NEUTRAL

LIVE

FUSED

SIDE NON-

FUSED

SIDE

Figure 3 - PCB Power Connections

CONNECTING THE PRESET FEEDBACK POTENTIOMETERS

If you are usin a preset Pan/Tilt head and lens, then CON2 provides the supplies and feedback connections for the

potentiometer wiper circuits. The direction of the feedback is automatically calculated when the test routine is invoked

(see Testing on pa e 18), this means it is not necessary to wire the pots in a specific direction.

Referrin to Fi ure 4, connect CON2 to the preset pots on the Pan/Tilt head and the lens. Connect any unused feedback

inputs to round. Make a note on your module description sheet of the preset connections and the type of lens.

CON2

TEST

BUTTON

10A

FUSE

Figure 4 - CON2 Connections

CAUTION

The maximum power that can be drawn from the +5V supply on CON2 is 30mA. DO NOT use this supply for any

purpose other than for supplying feedback pots.

Page 8

Pyramid AC Receiver Installation Manual

CONNECTING THE LENS DRIVE OUTPUTS

CON3 provides the lens drive outputs for focus, iris and zoom. The drive volta e is +10V DC at up to 100 mA. Refer to your

lens instructions and connect up the lens accordin to Fi ure 5.

CON6

CON3

ANTI-TAMPER

SWITCH

IRIS -

FOCUS

ZOOM -

IRIS +

FOCUS

ZOOM +

Figure 5 - CON3 Connections

CONNECTING THE PAN/TILT HEAD AND AUXILIARIES

CON4 contains the power output connections for the Pan/Tilt head and auxiliaries (AUX 1, AUX 2, AUX 3 and AUX 4).

Referrin to Fi ure 6, connect LEFT, RIGHT, UP and DOWN to the Pan/Tilt head and AUX 1 to wash, AUX 2 to wipe, AUX

3 to lamps and AUX 4 to camera power. Do not connect any unused auxiliaries. Connect all the return (neutral) wires to

the spare terminals on the external terminal block. Make a note on your module description sheet of your auxiliary

connections.

CAUTION

Maximum current is 1A per relay. Connect lamps using a separate relay as they can draw a surge current when they

fail. This may cause damage to the AC receiver.

CON4

CON

OWN

LEFT

IGHT

AUX 1

AUX 2

AUX 3

AUX 4

Figure 6 - CON4 Connections

Page 9

Installation Manual Pyramid AC Receiver

CONNECTING THE PAN/TILT HEAD AND AUXILIARIES POWER SOURCE

CON5 accepts the AC power input which is then switched to CON4. It powers the Pan/Tilt head and auxiliaries. CON5 can

be connected to either a 24V AC or Mains power supply.

For Mains Connections

Referrin to Fi ure 7, connect CON5 to the LIVE and NEUTRAL connections on the external terminal block. The connections

should be made to the non-fused side of the terminal block. The centre connection on CON5 is not connected.

FUSED

SIDE NON-

FUSED

SIDE

LIVE

NEUTRAL

LIVE

NEUTRAL

Figure 7 - Connecting CON5 to a Mains Power Supply

For 24V AC Connections

Connect the 24V AC power supply to the LIVE and NEUTRAL terminals on CON5 (see Fi ure 7 above). The centre

terminal on CON5 is Not Connected (NC).

WARNING

Never use both 24V AC and Mains on the same receiver PCB.

ANTI-TAMPER CONNECTIONS

CON6 is used as an input for an external anti-tamper switch. It is connected in parallel with the built in anti-tamper switch

that is marked in Fi ure 2.

On the boxed variants, the built in anti-tamper switch is connected in a normally open (N/O) confi uration. However, it is

fitted with a sprin which is compressed when the module lid is closed, and thus closin the contact. When the lid is

removed, the input is opened and the alarm will be activated.

If the built in anti-tamper switch is not used, CON6 can be connected to an external anti-tamper switch. To do this, the

sprin must be removed from the built in anti-tamper switch. CON6 should then be connected to the external anti-tamper

switch in a normally closed (N/C) confi uration.

VIDEO CONNECTIONS

All video must be connected to the receiver PCB via 75 ohm BNC connectors and video coaxial cable. Referrin to Fi ure

2, connect the video from your camera to VIDEO IN and connect VIDEO OUT to the matrix.

Your AC receiver has an on-board video amplifier with ain and lift. Adjustment of ain and lift is done remotely, usin a

Pyramid keyboard. For more details on adjustin ain and lift levels, consult the Pyramid 2 Keyboard Operating Manual.

Page 10

Pyramid AC Receiver Installation Manual

FITTING NETWORK CARDS

To connect the AC receiver to the network, it is first necessary to ensure that the correct Pyramid network card is fitted to

the PCB. The cards that can be used are as follows:

PY-COM Combined network card. Can be confi ured for use in RS485 and RS422 networks. Automatic

baud-rate selection between low and hi h speeds (9.8k b.p.s. or 78k b.p.s.).

PY-FTT Compatible with FTT10 (Flexible Topolo y) 2-wire bus-connected, half duplex. Hi h speed only.

PY-422 Compatible with RS422, 4-wire point-to-point, full duplex. Available in low and hi h speed variants.

PY-485 Compatible with RS485, 2-wire bus-connected, half duplex. Available in low and hi h speed variants.

PY-FI7 and PY-FI9 Compatible with dual, multi-mode fibre optic point-to-point connections. PY-FI7 operates at 78k

b.p.s., PY-FI9 operates at 9.8k b.p.s.

If the correct network card is not already fitted, chan e it usin Fi ure 8 as a uide.

CAUTION

To avoid damaging the module switch off the power before fitting the network card.

Figure 8 - Fitting a Network Card

Once a network card has been fitted, it must be connected to the network. The way in which this is done depends on the

type of network card in use. See the followin sections for more details.

Inhaltsverzeichnis

Andere Pyramid Empfänger Handbücher

Pyramid

Pyramid DC Receiver Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung