Pyronix EURO 46 V10 Bedienungsanleitung

EURO 46 V10

Installation Manual

PD6662:2010+IA501:2015

EN50131-1:2008+A1:2009

EN50131-3:2009

Security Grade (SG) 3 - Large

Security Grade (SG) 2 - Small

Environmental Class (EC) II

RINS1941-2

Software Version >10

EURO 46 V10 Installation Manual

System Overview 4

Default Codes 4

Input Mapping 5

Output Mapping 6

Regulatory Wiring Requirements 6

Technical Speciﬁcation 7

Out of the Box 9

The Printed Circuit Board 10

Communication Loom 11

Power and Battery Connections 12

485 Bus Wiring 13

Star and Daisy Chain Wiring 14

Input Connections 15

Output (PGM) Connections 16

Relay and Speaker Output 16

XPGM Outputs 16

External Sounder Connections 17

Grade 3 Wiring 17

Grade 2 Wiring 17

Modems 18

UDL Software 18

Connecting RS232 to the Panel 18

Connecting InSite to the Panel via RS232 19

Setting up a Cloud Connection 19

Connecting InSite to the Panel via the Cloud 20

EN 50131 Terminology 20

Access Levels 21

Compliance 21

Warranty 21

Additional Device Manuals 22

Wired Setting Devices 22

Wireless Setting Devices 22

Zone Expansion Modules 22

Output Expansion Modules 22

External Wired Sounders 22

Customer Support 23

Pyronix Training Academy Online 23

Pyronix Training Academy Training Videos 23

Technical Support 23

Contents

EURO 46 V10 Installation Manual

System Overview

System Overview EURO 46 V10 Additional Information

Areas

Independent areas 6

Wards 5 Each ward is created by a proximity reader

Inputs

On board 8 Supports N/C, 3EOL, DEOL and SEOL

Wireless 64 Requires 2 x EURO-ZEM32-WE

Maximum 76 Refer to ‘Input Mapping’ table

Outputs

PCB 5 1 Relay, 4 transistor (inputs 7 & 8 may be used as outputs)

AT E 10 Low power ATE outputs

Maximum 85 Refer to ‘Output Mapping’ table

User automation 30 Outputs programmed to activate on user command

Users

Users 75

Wireless key fobs 32 Requires 1 x EURO-ZEM32-WE

Guard/duress 10

Engineer 1

Maximum 87 Including Master Code and wireless key fobs

Arming Devices

Wired 6 Keypads and proximity readers

Wireless 4 Requires 1 x EURO-ZEM32-WE

Communication

Compatible modems PSTN, PSTN/VOICE, GSM, GPRS, Wi-Fi/XA and LAN

ARC formats Contact ID, Fast Format and SIA3 (also IP variants in all 3)

User formats Push notiﬁcations, SMS messaging and Voice messaging.

Phone numbers 10 Used for SMS messaging

UDL Support Ye s Using the upload/download software

Logs

Memory 1250 Memory type is EEPROM

Dimensions and Compliance

Dimensions

(H x W x D)

Small Case 297 x 250 x 82 mm

PCB 110 x 170 x 40 mm

Large Case 390 x 305 x 100 mm

EN grading 2 (small metal)

3 (large metal)

Environmental class II

Default Codes

Engineer - 1111

Master Manager - 2222

EURO 46 V10 Installation Manual

Input Mapping

Devices Address Input Numbers

EURO 46 V10 PCB N/A 1-8

EURO-ZEM8 / EURO-ZEM8+/ EURO-ZEM8+PSU /EURO-ZEM32-WE 0 9-16

EURO-ZEM8 / EURO-ZEM8+/ EURO-ZEM8+PSU /EURO-ZEM32-WE 1 17-24

EURO-ZEM8 / EURO-ZEM8+/ EURO-ZEM8+PSU /EURO-ZEM32-WE 2 25-32

EURO-ZEM8 / EURO-ZEM8+/ EURO-ZEM8+PSU /EURO-ZEM32-WE 3 33-40

EURO-ZEM8 / EURO-ZEM8+/ EURO-ZEM8+PSU /EURO-ZEM32-WE 4 41-48

EURO-ZEM8 / EURO-ZEM8+/ EURO-ZEM8+PSU /EURO-ZEM32-WE 5 49-56

EURO-ZEM8 / EURO-ZEM8+/ EURO-ZEM8+PSU /EURO-ZEM32-WE 6 57-64

EURO-ZEM8 / EURO-ZEM8+/ EURO-ZEM8+PSU /EURO-ZEM32-WE 7 65-72

EURO-LCD/EX 0 73-74

EURO-LCD/EX / EURO-PROX/INT 1 75-76

TOTAL 76

PLEASE NOTE: 2 x EURO-ZEM32-WE can be connected to the EURO 46 V10. Each expander

allows 32 inputs which are separated into 4 addresses (each address enables 8 wireless inputs). It is

possible to mix the wired and wireless remote expanders.

PLEASE NOTE: If the EURO-PROX/INT (Internal Tag Reader) is programmed as a ‘Set Point’ device,

2 inputs are enabled. If the EURO-PROX/INT is programmed as ‘Entry Control’ or ‘Access Control’

only 1 input is enabled.

EURO 46 V10 Installation Manual

Output Mapping

Devices Address Outputs Numbers

EURO 46 V10 APP PCB N/A 5 (2 shared)

Digi/ATE Outputs (using communication loom) N/A 10

EURO-OEM8R8T / EURO-OEM16R+PSU 0 1-16

EURO-OEM8R8T / EURO-OEM16R+PSU 1 17-32

EURO-ZEM8+/ EURO-ZEM8+PSU 0 1-4

EURO-ZEM8+/ EURO-ZEM8+PSU 1 1-4

EURO-ZEM8+/ EURO-ZEM8+PSU 2 1-4

EURO-ZEM8+/ EURO-ZEM8+PSU 3 1-4

EURO-ZEM8+/ EURO-ZEM8+PSU 4 1-4

EURO-ZEM8+/ EURO-ZEM8+PSU 5 1-4

EURO-ZEM8+/ EURO-ZEM8+PSU 6 1-4

EURO-ZEM8+/ EURO-ZEM8+PSU 7 1-4

EURO-LCD/EX 0 1

EURO-LCD/EX / EURO-PROX/INT / EURO-EXT-BK/W 1 1

EURO-LCD/EX / EURO-PROX/INT / EURO-EXT-BK/W 2 1

EURO-LCD/EX / EURO-PROX/INT / EURO-EXT-BK/W 3 1

EURO-LCD/EX / EURO-PROX/INT / EURO-EXT-BK/W 4 1

EURO-LCD/EX / EURO-PROX/INT / EURO-EXT-BK/W 5 1

Total 85

Regulatory Wiring Requirements

• Ensure wiring is done to the national wiring regulations in the country where the installation is

taking place. In the UK, this is BS 7671 Requirements for electrical installations; IET Wiring

Regulations (17th edition). If in doubt, consult a local qualiﬁed electrician.

• Ensure that a readily accessible disconnect device incorporated in the premises installation wiring

shall be provided external to the equipment with a contact separation of at least 3,0mm and

connected as closely as possible to the supply. Example: Fused Spur Unit

• When ﬁxing external wires, ensure that means are provided in the installation to prevent the SELV

(Safety Electrical Low Voltage) or signal circuits from coming into contact with live parts of the

power supply circuit. Wires shall be ﬁxed near their terminal blocks.

• The end of stranded conductor shall not be consolidated by soft soldering at places where the

conductor is subjected to contact pressure. Example: Must not solder ends of wires which are to be

secured in detector and control panel terminal connectors.

• On completion of wiring use tie-wraps to prevent any loose wires causing a safety hazard (material

of cables tie shall be rated at least HB or better).

• Cables ties and sleeves shall be separate for power supply cable and SELV (Safety Electrical Low

Voltage) wirings.

• Size of protective bonding conductors: minimum section 1.5mm². Example: Electrical Earth wire

connections.

EURO 46 V10 Installation Manual

Technical Speciﬁcation

Programming Outputs Power Rating Normal State Active State

PGM 1 Relay, 3A, max 30V Changeover NC & NO Changeover NC & NO

Speaker 16 ohms No tones Repeat RKP tones & internal

sounder

Strobe output 500mA 12v 0v

Bell output 500mA 12v 0v

XPGM 1 (Input 7) 50mA Floating 0v

XPGM 2 (Input 8) 50mA Floating 0v

ATE outputs 2mA 5v 0v

Circuit States

Resistance Range

1k / 1k Range 4k7 / 2k2 Range 4k7 / 4k7 Range

Normal 0k5 to 1k4 1k4 to 2k9 3k7 to 8k3

Alarm 1k5 to 5k9 4k2 to 7k8 8k4 to 10k2

Fault 6k to 8k1 8k to 11k3 10k3 to 14k9

Masking 8k2 to 17k 11k6 to 22k 15k to 22k

Tamper <0k5 or >17k <1k4 or >22k <3k7 or >22k

Fuses Value Type

Bell fuse for bell terminals F800mA quick blow 250V Glass

Aux fuse for aux terminals F800mA quick blow 250V Glass

RS485 bus fuse for bus terminals F800mA quick blow 250V Glass

Battery fuse for battery terminals T 1.5A anti-surge slow blow

250V Glass

230V mains fuse for mains terminals T500mA H anti-surge slow

blow 250V Ceramic

Panel Power Supply Output Nominal Range

Output voltage ~13.7VDC ~10-15VDC

Output current

Small Metal 1A Continuous 1.5A peak, during battery

charging

Large Metal 1.5A Continuous 2.0A peak, during battery

charging

Panel Power Supply Input Nominal Range

Mains supply voltage AC 230 VAC at 50Hz -15% +10 %

Transformer rating

Small metal 18VA 18V at 1.0A

Large metal 45VA 18.5V at 2.5A

Power Supply Type A.

Maximum output peak voltage: Max 100 mV

SD Voltage which the deep discharge protection function will operate at: 10V

Over Voltage Protection Trigger Voltage: 18V

Battery Charging Speciﬁcation

Float voltage 13.8VDC Recharge time <24 hours

Battery low voltage cut off 10.5V Standby battery capacity

current

300mA (3A to 6A)

700mA (7A to 17A)

EURO 46 V10 Installation Manual

PLEASE NOTE: EURO 46 V10 power supplies are NOT designed for use with multiple batteries

connected. System load should not exceed the panel power supply output shown above, or the

maximum load supportable by the battery for the speciﬁed backup time, as in the table shown below.

The power ratings are based on battery shown in table – but battery capable of supporting the

system load for the required time may be used without affecting these ratings.

EN50131-6:2008 Rated Output

In accordance with EN50131-6:2008, the EURO standby times and effective output currents depend on the Security Grade of the

system and how 230V mains missing fault is signalled to the Alarm Receiving Centre. Power supplies are rated in accordance with

the requirements of EN50131-6, which are related to the maximum battery size that can be accommodated in the housing and vary

according to the grade of the system in which they are installed, as per the following table:

Electrical Capability EN50131-6 Rating. Maximum Load

Example Battery Model Grade 2 Grade 3

Yuasa NP7-12 0.5A 0.3A

Yuasa NP17-12 1.2A 0.7A

EURO 46 V10 PCB Current Consumption Environmental

Quiescent 80mA Operational -10°C to +40°C, Certiﬁed

User Code and Tag Guessing Storage -20°C to +60°C

4-digit codes 10,000 Humidity 75%

6-digit codes 100,000 Dimensions

Disallowed codes None

Metal case

Small case 250 x 297 x 82mm

Weight: 4.8kg inc. battery

All codes 1612 Large case 390 x 305 x 100mm

Weight: 11.5kg inc. battery

According to EN50131-3:2009 Annex B PCB 170 x 90 x 30mm

According to spec of manufacturer of RFID components used EN50131 Grading 3

The below table speciﬁes ATS (Alarm Transmission System) performance criteria in accordance with

the requirements of EN50136-1.

Notiﬁcation Equipment

Grade 2 Criteria Grade 3 Criteria

Options Options

A B C D A B C D

Remotely powered external sounder 2Optional Optional Optional 2Optional Optional Optional

Self-powered external sounder Optional 1Optional Optional Optional 1Optional Optional

Main communication path (ATS) ATS 2 ATS 2 ATS 2 ATS 3 ATS 4 ATS 4 ATS 4 ATS 5

Second communication path (ATS) Optional Optional ATS 1 Optional Optional Optional ATS 3 Optional

EURO 46 V10 Installation Manual

Out of the Box

Unscrew and remove the cover of the EURO 46 V10 (Figure

1). The EURO 46 V10 printed circuit board is located to the

top right hand side. (Figure 2)

Install the supplied stand-offs if needed before mounting the

metal case to the wall (Figure 3).

Connect any modems if required and any other devices

(input expanders, output expanders etc.) before powering up

the system.

Screw the back metal plate to the wall.

Wire the telephone line if the DIGI-1200 modem (PSTN) is

installed or the LAN cable if the DIGI-LAN is installed.

Install the SIM card, connect the antenna and locate outside

of the metal casing if the GPRS or Wi-Fi modem is used.

EURO 46 V10: The tamper mechanism comes already ﬁtted.

Figure 1

Figure 2

Figure 3

Secure all the wires and close the enclosure making sure the

tamper is operational.

Turn on the power to the EURO 46 V10.

On power up, the panel will typically show the below screens.

485 COMMS FAIL >>PLEASE WAIT<< EURO 46 V10

Time 10:09 c

EURO 46 V10 Installation Manual

The Printed Circuit Board

1: Case tamper ‘Hold-Off’ jumper

2: PGM 1

3: Speaker connection

Connects a 16ohm speaker.

4: External sounder connections

Connects an external sounder.

5: Input connections

8 Fully programmable inputs.

6: Tamper switch

Optional tamper protection for the metal casing.

7: Auxiliary 12V power

12V power supply

8: Inputs or outputs

Inputs 7 and 8 may be programmed as outputs

if unused.

9: Battery connect ‘Kick-start’ switch

To power-up and program from battery power

(when there is no mains power available).

10: RS485 bus terminals

Connects peripherals.

11: Battery connection

For battery back up.

12: Earth connection

Connects the earth.

13: 17V connection

Connects the AC transformer 17V supply.

14: Battery charge capacity jumper

For battery back up.

15: Modem connections

The left connector (labelled ‘modem’) is for

signalling modems.

PLEASE NOTE: The right is ‘For Future Use’,

please do not use.

16: RS232 Connection

This connection is used for an RS232 lead that

will connect to a PC to allow uploading and

downloading of data using the InSite software.

17: Communication Outputs

Connects the supplied communication loom to

enable an additional 9 programmable outputs.

These are low current and would normally

be used when connecting a stand-alone

communicator to the panel.

18: Bell Fuse

19: Auxiliary Fuse

20: Bus Fuse

21: Battery Fuse

MODEM FOR FUTURE

USE

Andere Handbücher für EURO 46 V10

Inhaltsverzeichnis

Andere Pyronix Sicherheitssystem Handbücher

Pyronix

Pyronix Matrix 424 Bedienungsanleitung

Pyronix

Pyronix PCX-12 Bedienungsanleitung

Pyronix

Pyronix Deltabell E Bedienungsanleitung

Pyronix

Pyronix ENFORCER RINS1706-1 Service-Handbuch

Pyronix

Pyronix Enforcer Einrichtungshandbuch

Pyronix

Pyronix Paragon E Montageanleitung

Pyronix

Pyronix Enforcer 32WE Bedienungsanleitung

Pyronix

Pyronix RINS1902-2 Bedienungsanleitung

Pyronix

Pyronix Enforcer V10 Bedienungsanleitung

Pyronix

Pyronix Enforcer 32-W Bedienungsanleitung

Pyronix

Pyronix Matrix 6/816 Bedienungsanleitung

Pyronix

Pyronix PCX 256 Bedienungsanleitung

Pyronix

Pyronix Enforcer Bedienungsanleitung

Pyronix

Pyronix Wireless Alarm system Bedienungsanleitung

Pyronix

Pyronix PCX 256 Bedienungsanleitung

Pyronix

Pyronix OCTAGON II Bedienungsanleitung

Pyronix

Pyronix PARAGON E Bedienungsanleitung

Pyronix

Pyronix Vocaliser Bedienungsanleitung

Pyronix

Pyronix Enforcer Bedienungsanleitung

Pyronix

Pyronix Paragon Plus Bedienungsanleitung

Pyronix

Pyronix V2 TEL Bedienungsanleitung

Pyronix

Pyronix Enforcer 32WE Bedienungsanleitung

Pyronix

Pyronix XDL12TT-AM Bedienungsanleitung

Pyronix

Pyronix EURO 46 APP Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung