Qlogic SANbox-16STD Installer's/ Bedienungsanleitung

Preliminary

SANbox-16STD

Fibre Channel Switch

Installer’s/ ser’s Manual

Publication No. 59012-03 Rev. A

Preliminary

QLogic Corporation

6321 ury Drive

Eden Prairie, MN 55346

(952) 932-4000

Release Number 03, Revision A (August, 2000)

The following paragraph does not apply to the United Kingdom or any country where such provisions are inconsistent

with local law: THIS PU LICATION is printed “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR

IMPLIED, INCLUDING, UT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTA ILITY OR FITNESS FOR A

PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions;

therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the

information herein; These changes will be incorporated in new additions of the publication.

It is possible that this publication may contain reference to, or information about, products (machines and programs),

programming, or services that are not announced in your country. Such references or information must not be

construed to mean that such products, programming, or services will be offered in your country. Any reference to a

licensed program in this publication is not intended to state or imply that you can use only the licensed program

indicated. You can use any functionally equivalent program instead.

SANbox, SANsurfer, and Multistage are trademarks of QLogic Corporation

I M® is a registered trademark of I M Corporation.

Microsoft and Microsoft Excel are trademarks or Registered Trademarks of Microsoft Corporation.

Note to US Government Users – Documentation and programs related to restricted rights – Use, duplication, or disclo-

sure are subject to the restrictions set forth in GSA ADP Schedule Contract.

Preliminary

SANbox-16STD Fibre Channel Switch

Installer’s/ ser’s Manual 59012-03 Rev. A

iii

Table of Contents

Preface

How to Use This Manual 1

Intended Audience 1

Related Materials 2

Safety Notices 3

Sicherheitshinweise 3

Notes informatives relatives à la sécurité 3

Communications Statements 4

Federal Communications Commission (FCC) Class A Statement 4

Canadian Department of Communications Class A Compliance Statement 4

Avis de conformité aux normes du ministère des Communications du Canada 4

CE Statement 5

VCCI Class A Statement 6

Laser Safety Information 7

Labeling Requirements 7

Accessible Parts 8

Pièces Accessibles 8

Zugängliche Teile 8

QLogic Customer Support 8

General Description

Introduction 1-1

Major Fibre Channel Port Features 1-2

Fabric Port Overview 1-3

Segmented Loop Port (SL_Port) Overview 1-3

Translated Loop Port (TL_Port) Overview 1-5

Major Switch Chassis Features 1-10

Major Switch Management Features 1-11

Switch Management Tools 1-15

SANsurfer Switch Management Application 1-15

Telnet 1-15

Trivial File Transfer Protocol (TFTP) 1-16

Simple Network Management Protocol (SNMP) 1-16

Fibre Channel Ports 1-17

Giga it Interface Converters (G ICs) 1-18

Front Panel Controls 1-19

Preliminary

SANbox-16STD Fibre Channel Switch

59012-03 Rev. A Installer’s/ ser’s Manual

Power Switch 1-19

Test Mode Switch 1-19

Front Panel LEDs 1-20

Heartbeat LED (Yellow) 1-20

Switch Logic Power Good LED (Green) 1-20

Fan Fail LED (RED) 1-20

Over Temperature LED (Red) 1-20

Logged-In LED (Green) 1-21

Trafﬁc LED (Yellow) 1-21

AC Input Power Connector and Fuses 1-22

Switch Management Connector 1-22

Installation

Introduction 2-1

Unpack 2-2

Place or Mount the Equipment 2-2

Shelf Mount 2-2

Rack Mount 2-3

Apply the IEC Class 1 Laser Information Label (If the installation is in Europe) 2-5

Install G ICs 2-6

Connect to AC Power 2-6

Switch Logic Power Good LED 2-8

Check the Power-On-Self-Test (POST) Results 2-8

Cable Fibre Channel Devices to the Switch 2-9

Public Devices 2-9

Private Devices 2-10

Mixing Public and Private Devices on the Same Loop. 2-10

Switch Ports 2-10

Tuning 2-10

Distance 2-11

Port uffer Credits 2-11

Hot-Pluggable 2-12

Incorrect Cabling 2-12

Connections 2-12

Examples 2-13

Conﬁgure the Chassis 2-18

Conﬁgure the Ports 2-19

Fabric Ports 2-19

SL_Ports 2-19

TL_Ports 2-20

T_Ports 2-20

Tuning Ports for Multi-Frame Sequences 2-21

Preliminary

SANbox-16STD Fibre Channel Switch

Installer’s/ ser’s Manual 59012-03 Rev. A

Zoning 2-22

Rack and Shelf Administration 2-23

Operating the Switch 2-23

Diagnostics/Troubleshooting

Introduction 3-1

Power Supply Troubleshooting 3-1

Power-On-Self-Test (POST) 3-2

Overview 3-2

Heartbeat LED link Patterns 3-4

Test/Failure Descriptions 3-4

Cable Continuity Tests 3-8

Removal/Replacement Procedures

Introduction 4-1

Input Fuse 4-1

Removal 4-1

Replacement 4-2

G IC 4-3

Removal 4-3

Replacement 4-4

attery (Repair Depot Only) 4-5

Multi-Chassis Fabrics

Introduction 5-1

Three Multi-Chassis Topologies 5-1

Choosing a Topology 5-2

Cascade Topology 5-5

Cascade Fabric Size 5-6

Cascade Latency 5-6

Cascade andwidth 5-6

Cascade Physical Distance between Chassis 5-7

Cascade Zoning 5-7

MKII Compatibility 5-8

Mesh Topology 5-8

Mesh Fabric Size 5-8

Mesh Latency 5-9

Mesh andwidth 5-9

Mesh Physical Distance etween Chassis 5-9

Mesh Zoning 5-10

MKII Compatibility 5-10

Multistage Topology 5-11

Preliminary

SANbox-16STD Fibre Channel Switch

59012-03 Rev. A Installer’s/ ser’s Manual

T_Port Rules for SANbox IO/T Chassis 5-11

T_Port Rules for SANbox Cross-Connect (CC) Chassis 5-11

Multistage Fabric Size 5-11

Multistage Latency 5-11

Multistage andwidth 5-12

Multistage Physical Distance etween Chassis 5-12

Multistage Zoning 5-12

MKII Compatibility 5-12

Multistage Examples 5-13

Cabling 5-16

Fiber Optic T_Port Connections 5-16

Copper T_Port Connections 5-16

T_Port Cable Length 5-16

Device Connections 5-16

Chassis Conﬁguration 5-17

Chassis Conﬁguration Process 5-18

Reference Information

QLogic Customer Support A-1

SANbox-16STD Fibre Channel Switch Speciﬁcations A-2

Switch A-2

Switch Maintainability A-3

Fabric Management A-4

Switch Mechanical A-4

Switch Electrical A-4

Switch Environmental A-4

Switch Regulatory Certiﬁcations A-5

Shortwave Laser G IC (multi-mode) A-6

Longwave Laser G IC (single-mode) A-6

Copper Inter-Enclosure G IC (active) A-6

Copper Intra-Enclosure G IC (passive) A-7

QLogic Customer Support

Help Desk -1

Hardware Support -2

Software Support -2

Customer Responsibilities -2

Index

Preliminary

SANbox-16STD Fibre Channel Switch

Installer’s/ ser’s Manual 59012-03 Rev. A List of Figures

vii

List of Figures

Figure 1-1 SANbox-16STD Fibre Channel Switch 1-1

Figure 1-2 Segmented Loop Topology Example 1-4

Figure 1-3 SCSI Example 1-6

Figure 1-4 TCP/IP Example 1-7

Figure 1-5 Chassis Front 1-17

Figure 1-6 Typical G IC 1-18

Figure 1-7 Test Mode Switch 1-19

Figure 2-1 Cabinet Mounting racket 2-4

Figure 2-2 IEC Class 1 Laser Information Label 2-5

Figure 2-3 Extending uffer Credits by Chaining Ports 2-12

Figure 2-4 Cabling 2-14

Figure 2-5 Variety of Public Connections 2-15

Figure 2-6 Private Segmented Loop Connections 2-16

Figure 2-7 Private Translated Loop Connections 2-17

Figure 3-1 Test Mode Switch 3-2

Figure 4-1 Fuse Holder Removal 4-1

Figure 4-2 Fuse Replacement 4-2

Figure 4-3 Removing G ICs that have individually operated latches 4-3

Figure 4-4 Removing G ICs that have bail-operated latches 4-4

Figure 4-5 Replacing G ICs 4-4

Figure 5-1 Cascade Example 5-5

Figure 5-2 Mesh Example 5-8

Figure 5-3 SANbox-16 Multistage with one T_Port link from each IO/T chassis 5-13

Figure 5-4 SANbox-16 Multistage with two T_Port links from each IO/T chassis 5-14

Figure 5-5 SANbox-16 Multistage with eight CC chassis 5-15

Figure A-1 SANbox-16STD Switch Dimensions in Millimeters (Inches) A-8

SANbox-16STD Fibre Channel Switch

List of Figures 59012-03 Rev. A Installer’s/ ser’s Manual

Notes

Preliminary

SANbox-16STD Fibre Channel Switch

Installer’s/ ser’s Manual 59012-03 Rev. A Preface

Preface

How to se This Manual

This manual has ﬁve sections and two appendixes:

•Section 1 is an overview of the Switch. It describes indicator lights and all

user controls and connections.

•Section 2 explains how to install the Switch.

•Section 3 contains troubleshooting procedures, and explains the Power-On-

Self-Test (POST).

•Section 4 contains removal/replacement procedures for all ﬁeld replaceable

units (FRUs).

•Section 5 explains how to expand the size of a Switch fabric to multiple

Switch chassis.

•Appendix A contains reference information.

•Appendix B contains information about QLogic Customer Support and how

to contact us for assistance.

Please read the communications statements and laser safety information presented

on the next pages in this Preface.

Please use this manual in conjunction with the Switch Management Installer’s/

User’s manual listed in “Related Materials”. The Switch Management manual

contains information about managing Switch chassis through all available means.

Intended Audience

This manual introduces users to the Switch and explains its installation and

service. It is intended for users competent in installing and servicing electronic

equipment.

Preliminary

SANbox-16STD Fibre Channel Switch

Preface 59012-03 Rev. A Installer’s/ ser’s Manual

Related Materials

The following manuals and materials are referenced in the text and/or provide

additional information.

• Switch Management Installer’s/User’s Manual, Publication Number 59010.

Available from QLogic Communications.

• Fibre Channel-Arbitrated Loop (FC-AL-2) Rev. 6.8

• Fibre Channel-Private Loop SCSI DirectAttach (FC-PLDA)

NCITS TR-19:1998

• Fibre Channel-10-bit Interface Rev. 2.3

• Deﬁnitions of Managed Objects for the Fabric Element in Fibre Channel

Standard (draft-ietf-ipfc-fabric-element-mib-04.txt).

The Fibre Channel Standards are available from:

Global Engineering Documents, 15 Inverness Way East, Englewood, CO

80112-5776 Phone: (800) 854-7179 or (303) 397-7956

Fax: (303) 397-2740

Andere Qlogic Schalten Handbücher

Qlogic

Qlogic SilverStorm 9000 Handbuch

Qlogic

Qlogic 5600Q Bedienungsanleitung

Qlogic

Qlogic SANbox2 SANbox2-64 Handbuch

Qlogic

Qlogic SilverStorm 9120 Bedienungsanleitung

Qlogic

Qlogic SANbox 5600 Series Handbuch

Qlogic

Qlogic SANbox 5800V Series Bedienungsanleitung

Qlogic

Qlogic SANbox2-16 Fibre Channel Bedienungsanleitung

Qlogic

Qlogic SANbox 5200 Series Handbuch

Qlogic

Qlogic SilverStorm 9024 Bedienungsanleitung

Qlogic

Qlogic SANbox 3810 Bedienungsanleitung

Qlogic

Qlogic SANbox2 SANbox2-64 Handbuch

Qlogic

Qlogic StorEdge Sun StorEdge Handbuch

Qlogic

Qlogic QLogic 12000 Series Bedienungsanleitung

Qlogic

Qlogic SilverStorm 9020 Bedienungsanleitung

Qlogic

Qlogic SANbox 5800V Series Bedienungsanleitung

Qlogic

Qlogic QLogic 12000 Series Bedienungsanleitung

Qlogic

Qlogic SilverStorm 9000 Bedienungsanleitung

Qlogic

Qlogic 3000 Series Bedienungsanleitung

Qlogic

Qlogic SilverStorm 9040 Bedienungsanleitung

Qlogic

Qlogic SANbox 5802V Bedienungsanleitung

Qlogic

Qlogic SANbox 9000 Series Bedienungsanleitung

Qlogic

Qlogic SANbox 1400 Series Handbuch

Qlogic

Qlogic SANbox 5200 Series Handbuch

Qlogic

Qlogic SANbox 9100 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung