Quantum Scalar 50 Kurzanleitung
81-81792-01 A01, July 2007 1
Quantum Scalar 50
TC2201 iSCSI Bridge
Upgrade Instructions
Introduction 3
TC2201 Bridge Operation ............................................................................ 3
Preparing for the TC2201 Installation 3
Required Upgrade Kits ................................................................................ 3
Required Tools .............................................................................................. 4
TC2201 Upgrade Procedure 4
Preparing the Quantum Scalar 50 Library ................................................ 4
Removing Tape Drive SCSI Cables ............................................................ 5
Installing the TC2201 Bridge ....................................................................... 6
Installing the Ethernet Cables ..................................................................... 8
Installing SCSI Cables .................................................................................. 8
Configuring the TC2201 Bridge Software ............................................... 11
Quantum Scalar 50 TC2201 iSCSI Bridge Upgrade Instructions
81-81792-01 A01
July 2007
Made in the USA.
Quantum Corporation provides this publication “as is” without warranty of any kind, either express or implied, including but not limited to
the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to
time without notice.
COPYRIGHT STATEMENT
© Copyright 2007 by Quantum Corporation. All rights reserved.
Your right to copy this document is limited by copyright law. Making copies or adaptations without prior written authorization of Quantum
Corporation is prohibited by law and constitutes a punishable violation of the law.
TRADEMARK STATEMENT
Capacity on Demand (CoD), Crosslink Mechanism, DLT, DLTSage, DLTtape, Super DLTtape, Performance on Demand, (PoD), PRISM,
PRISM Storage Architecture logo, SiteCare, StackLink, StorageCare, SuperLoader, and ValueLoader are all trademarks of Quantum
Corporation. Quantum, the Quantum logo, and the DLTtape logo are all registered trademarks of Quantum Corporation.
Other trademarks may be mentioned herein which belong to other companies.
2
Quantum Scalar 50 TC2201 iSCSI Bridge Upgrade Instructions
81-81792-01 A01
July 2007
Introduction 3
Introduction 0
The Quantum Scalar 50 automated tape libraries are controlled by a host
computer via a SCSI LVD bus using the SCSI-3 medium changer command
set.
The Quantum Scalar 50 allows for easy conversion from the SCSI host
interface to an iSCSI host interface. This document describes upgrading a
standard Scalar 50 library equipped with a SCSI host interface to an iSCSI
host interface using a TC2201 Upgrade kit.
TC2201 Bridge
Operation 0
Once a TC2201 bridge option is installed and tested, the library operates
exactly as a Scalar 50 with a SCSI host interface. Operation of the library via
the operator control panel (OCP) is unchanged.
Preparing for the TC2201 Installation 0
Before beginning the installation procedure, make sure that you have the
required upgrade kit and tools.
Required Upgrade Kits 0The TC2201 installation requires the following upgrade kit for every two tape
drives in a Scalar 50 library (see table 1):
Table 1 TC2201 Upgrade
Kit PN PR-UU9WG-YF
Note: All part numbers are subject to change without notice.
Qty Description
1 TC2201 PWA
2 SCSI Cables
1 Ethernet cross-over cable
1Terminator
1 Quantum Scalar 50 TC2201 Upgrade Instructions
Quantum Scalar 50 TC2201 iSCSI Bridge Upgrade Instructions
81-81792-01 A01
July 2007
4 TC2201 Upgrade Procedure
Required Tools 0The following tools are required to install the TC2201 bridge upgrade:
• #2 PHILLIPS® screwdriver
TC2201 Upgrade Procedure 0
The upgrade procedure is identical regardless of the number of TC2201s
installed except where noted. The upgrade procedure consists of the
following major steps:
•Preparing the Quantum Scalar 50 Library
•Removing Tape Drive SCSI Cables
•Installing the TC2201 Bridge
•Installing the Ethernet Cables
•Installing SCSI Cables
•Configuring the TC2201 Bridge Software
Preparing the
Quantum Scalar 50
Library 0
To prepare the Scalar 50 library:
1With the library turned on, press the Ops button on the OCP to access the
Operations screen (see figure 1).
Figure 1 Operations
Screen
2Select Library operations and press Enter.
3From the library operations menu, select Library on/offline and press Enter
to turn the library offline.
4Verify that the OCP display indicates “Offline” from the OCP screen.
Caution: Use appropriate ESD procedures when assembling and
installing the TC2201 option.
Enter
Quantum Scalar 50 TC2201 iSCSI Bridge Upgrade Instructions
81-81792-01 A01
July 2007
TC2201 Upgrade Procedure 5
5Turn off the power by pressing the power button located on the front of
the library (see figure 2).
Figure 2 Turning Off the
Library
Removing Tape Drive
SCSI Cables 0
Each pair of tape drives within the library are connected via a SCSI cable.
These cables must be removed prior to cabling the TC2201.
1Locate the SCSI cables connecting each pair of tape drives in the library
and the host systems (see figure 3). Tape drive 1 is in the upper right-
hand drive bay, tape drive 2 is in the upper left-hand drive bay, and so
forth.
Figure 3 Scalar 50 Cabling
Configuration
2Remove all SCSI cables connecting each tape drive and also all
terminators.
Note: Save the SCSI cables connected to the SCB for later use.
Power button
OCP
Back of Library
SCSI host
Ethernet
Power
System Controller Board
Tape drive 1Tape drive 2
Quantum Scalar 50 TC2201 iSCSI Bridge Upgrade Instructions
81-81792-01 A01
July 2007
6 TC2201 Upgrade Procedure
Installing the TC2201
Bridge 0
To install the TC2201 bridge:
1Loosen the two PHILLIPS screws securing the blank off plate to the CPCI
card cage and expose the slot needed for the TC2201 installation.
2With the SCSI ports located to your right as you face the back of the
library, slide the first TC2201 into the slot of the card cage (see figure 4).
Figure 4 Installing a
TC2201 Bridge
3Gently press down on the TC2201 until the board is seated in the card
cage and the ejector latches lock in place (see figure 5).
Blank off plate
Screws
Card cage
TC2201
Quantum Scalar 50 TC2201 iSCSI Bridge Upgrade Instructions
81-81792-01 A01
July 2007
TC2201 Upgrade Procedure 7
Figure 5 Seating the
TC2201 Bridge
4Secure each bridge to the CPCI card cage by tightening the captive screws
located in the ejector latches with a PHILLIPS screw driver (see figure 6).
Figure 6 Securing the
TC2201 Bridge
5Repeat step 2 through step 4 for additional TC2201 bridges if necessary,
using the next available card cage slot.
Ejector latches in
locked position
Ejector latches
Captive screws
Quantum Scalar 50 TC2201 iSCSI Bridge Upgrade Instructions
81-81792-01 A01
July 2007
8 TC2201 Upgrade Procedure
Installing the Ethernet
Cables 0
Scalar 50 libraries with an installed TC2201 iSCSI bridge must have the
following Ethernet connection:
1Connect a cross-over cable between the right port of the library system
controller board (SCB) and the TC2201 (see figure 7).
Figure 7 Scalar Ethernet
Connection
Installing SCSI Cables 0The SCSI cable installation procedure differs depending on the type of tape
drive installed. Refer to the following sections for installing the SCSI cables:
•Installing SCSI Cables with Full Height Tape Drives
•Installing SCSI Cables with Half-Height Tape Drives
Installing SCSI Cables with Full Height Tape Drives 0
Use the following procedure to connect the SCSI cables and terminators to the
tape drives and TC2201.
• SCSI connectors 0 through 1 on the TC2201 are used to connect to the
system controller board and tape drives 1 through 2.
To cable a TC2201 bridge to the tape drive(s):
1To connect the SCSI cables from the TC2201 to the tape drives (see
figure 10 and figure 9):
aConnect a SCSI cable (VHDC 68-pin to HD 68-pin) from the top port
of the system controller board to Port 0 on the TC2201.
bConnect a SCSI cable (VHDC 68-pin to HD 68-pin) from the bottom
port of the system controller board to the upper port of tape drive 1.
cInstall a terminator on the bottom port of tape drive 1.
Cross-over cable TC2201SCB (right port)
Quantum Scalar 50 TC2201 iSCSI Bridge Upgrade Instructions
81-81792-01 A01
July 2007
TC2201 Upgrade Procedure 9
dConnect a SCSI cable (VHDC 68-pin to HD 68-pin) from the top port
of tape drive 2 to Port 1 on the TC2201.
eInstall a terminator on the bottom port of tape drive 2.
Figure 8 Cabling a
TC2201 Bridge to the Tape
Drives
Figure 9 Scalar SCSI
Connections (Full Height
Drives)
Ethernet port
iSCSI ports
SCSI port 0
SCSI port 1
TC2201
Tape drive 1Tape drive 2
Quantum Scalar 50 TC2201 iSCSI Bridge Upgrade Instructions
81-81792-01 A01
July 2007
10 TC2201 Upgrade Procedure
Installing SCSI Cables with Half-Height Tape Drives 0
Use the following procedure to connect the SCSI cables and terminators to the
tape drives and TC2201.
• SCSI connectors 0 through 1 on the TC2201 are used to connect to the
system controller board and tape drives 1 through 4.
To cable a TC2201 bridge to the tape drive(s):
1To connect the SCSI cables from the TC2201 to the tape drives (see
figure 10 and figure 9):
aConnect a SCSI cable (VHDC 68-pin to HD 68-pin) from the top port
of the system controller board to Port 0 on the TC2201.
bConnect a SCSI cable (VHDC 68-pin to HD 68-pin) from the bottom
port of the system controller board to the upper port of tape drive 1.
cConnect a SCSI cable (HD 68-pin to HD 68-pin) from the bottom port
of tape drive 1 to the top port of tape drive 2.
dInstall a terminator on the bottom port of tape drive 2.
eConnect a SCSI cable (VHDC 68-pin to HD 68-pin) from the top port
of tape drive 3 to Port 1 on the TC2201.
fConnect a SCSI cable (HD 68-pin to HD 68-pin) from the bottom port
of tape drive 3 to the top port of tape drive 4.
gInstall a terminator on the bottom port of tape drive 4.
Figure 10 Cabling a
TC2201 Bridge to the Tape
Drives
Ethernet port
iSCSI ports
SCSI port 0
SCSI port 1
Andere Handbücher für Scalar 50
6
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Quantum Netzwerk-Hardware Handbücher
Quantum
Quantum MC300 Prism Bedienungsanleitung
Quantum
Quantum DXi4800 Bedienungsanleitung
Quantum
Quantum DX Series Bedienungsanleitung
Quantum
Quantum FC420 Bedienungsanleitung
Quantum
Quantum CHECK POINT SPARK 1500 Series Bedienungsanleitung
Quantum
Quantum VS2112-NVR Bedienungsanleitung
Quantum
Quantum SMART-1 6000-L Bedienungsanleitung
Quantum
Quantum 1U Bedienungsanleitung
Quantum
Quantum LightSpeed Appliance QLS250 Bedienungsanleitung
Quantum
Quantum B DLTSAGE SELLSHEET Bedienungsanleitung
Beliebte Netzwerk-Hardware Handbücher anderer Marken
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung
Yudor
Yudor YDS-16 Bedienungsanleitung
D-Link
D-Link ShareCenter DNS-320L Bedienungsanleitung
Samsung
Samsung ES1642dc Gebrauchsanweisung
Honeywell Home
Honeywell Home LTEM-PV Montageanleitung
