Quantum PX720 Bedienungsanleitung
PX720 DLTSage™ Tape Security
Quick Start Guide
TABLE OF CONTENTS
Introduction .......................................1
Notational Conventions .................1
Creating a Secure User ......................1
Creating a Secure Key........................2
Protection Mode for Cartridges.....3
Enable/Disable Secure Key for
Drives...............................................4
Modify Secure Key for Library .......4
Assign Secure Key to Cartridge......4
Create Secure Key Name/Secure Key
Pair...................................................5
Delete Secure Key Name.................5
Backup Secure Key File ...................5
Upload Secure Key File ...................6
Importing Secured Tape Cartridges ..6
Secure Key Maintenance ...................7
Introduction 0
The PX720 tape library with DLT-S4 tape drives is capable of utilizing DLTSage Tape
security. DLTSage Tape Security is a unique solution designed to prevent
unauthorized access to tape cartridges which is particularly valuable when
protecting tapes that are transported offsite. DLTSage Tape Security is a firmware
feature designed into the DLT-S4 tape drive which uses an electronic key to prevent
or allow reading and writing of data on to a tape cartridge. This key is managed
through the remote management pages of the PX720 tape library (refer to the
Quantum PX720 User’s Guide
, PN 6444601 located on the
PX720 Documentation
CD
for more information on the remote management pages). DLTSage Tape
Security is available at no additional cost as an integrated feature of the DLT-S4
tape drive and PX720 tape library (firmware revision 4.5 or later).
Notational Conventions 0
This instruction uses the following conventions:
Setting up your PX720 tape library with DLTSage Tape Security consists of the
following steps:
•Creating a Secure User
•Creating a Secure Key
Creating a Secure User 0
The Secure User is the only user that has the ability to create, modify, and delete a
Secure Key for the Library. The Secure User also has the ability to enable and
NOTE:Notes emphasize important information related to the main topic.
CAUTION:Cautions indicate potential hazards to equipment and are included
to prevent damage to equipment.
WARNING:Warnings indicate potential hazards to personal safety and are
included to prevent injury.
CAUTION:If the secure key information is lost, any tape cartridges that were
secured with the lost key will be unavailable for reading or writing.
PX720 DLTSage™ Tape Security Quick Start Guide
2
disable Secure Capable Drives for reading and writing
data to and from tapes using the Secure Key.
When a user is created with administrator privileges (other
than the default admin user), the Create Secure User
section appears at the bottom of the Users page (see
figure 1).
Figure 1 Create Secure User
To create a secure user:
There is only one Secure User and the username is always
securekeyadmin.
1Enter a secure password.
2Verify the secure password by entering the password a
second time in the Verify Password box.
3Click Create to create the secure key password.
Once the secure key administrator password is added,
the Delete Secure User section displays at the bottom
of the Users page (see figure 2).
Figure 2 Delete Secure User
To update the secure key password:
NOTE:Only users with administrator privileges (other
than the default administrator) can create a
secure user.
NOTE:Secure Passwords must be alphanumeric
strings of at least one character. A blank
secure password will be rejected. Secure
Password and Verify Password must
match.
NOTE:Only the Secure User can change the secure user
password.
1Enter a secure password.
2Verify the secure password by entering the password a
second time in the Verify Password box.
3Click Update to update the secure key password.
The secure key password is updated.
Creating a Secure Key 0
The Secure Key tab displays when a secure user has been
added to the library and the secure user is logged in.
To access the Secure Key page, from the Setup page, click
on the Secure Key tab at the top of the page.
The Secure Key page displays (see figure 3).
NOTE:Secure Passwords must be alphanumeric
strings of at least one character. A blank
secure password will be rejected. Secure
Password and Verify Password must
match.
NOTE:When logging on as a secure user, the IP address
entered in the address line of the internet browser
uses https, not the common http. Example:
https://<ip address>
PX720 DLTSage™ Tape Security Quick Start Guide
3
Figure 3 Secure Key Page The Secure Key page is divided into the following sections:
•Protection Mode for Cartridges
•Enable/Disable Secure Key for Drives
•Modify Secure Key for Library
•Assign Secure Key to Cartridge
•Create Secure Key Name/Secure Key Pair
•Delete Secure Key Name
•Backup Secure Key File
•Upload Secure Key File
Protection Mode for
Cartridges 0
Refer to figure 4 for information on Protection Mode for
Cartridges.
Figure 4 Protection Mode for
Cartridges
The Protection Mode for Cartridges area defines when the
secure key is used for a cartridge in a tape drive with a
secure key enabled. In all modes, the secure key is used to
read data from cartridges that have a pre-existing secure
key. If the secure key on the cartridge does not match the
current secure key on the library, the data on the cartridge
can not be read.
Three write protection modes are available:
•Never Write Secure Key to a Cartridge - The secure
key will never be written to a cartridge placed in a
secured tape drive.
•Only Write Secure Key to Blank Cartridges - The
secure key will only be written to blank, unformatted
cartridges.
PX720 DLTSage™ Tape Security Quick Start Guide
4
•Write Secure Key to All Cartridges - The secure key
will be written to all cartridges, including blank and
formatted cartridges containing data. This mode may
be used to apply a secure key to cartridges with pre-
existing data.
Enable/Disable Secure Key
for Drives 0
Refer to figure 5 for information on Enable/Disable Secure
Key for Drives.
Figure 5 Enable/Disable Secure
Key for Drives
The secure key can only be used with tape drives that are
secure key capable. This section lists the tape drives in the
library that are secure key capable. A checkmark in the
Secure Key column indicates a secure key is enabled for the
tape drive.
1The secure key can be enabled or disabled for all tape
drives by clicking the corresponding radio button.
2Click the Secure Key check box for individual tape
drives to enable/disable secure key for a tape drive.
3Click Update to activate the changes.
Modify Secure Key for
Library 0
Refer to figure 6 for information on Modify Secure Key for
Library.
NOTE:The system must be offline to Enable/Disable
Secure Key setting for drives.
Figure 6 Modify Secure Key for
Library
To modify the secure key used by the library:
1Select the secure key name from the list of available
names.
2Click Update.
Assign Secure Key to
Cartridge 0
Refer to figure 7 for information on Assign Secure Key to
Cartridge.
Figure 7 Assign Secure Key to
Cartridge
Click Find to list all secured cartridges and their assigned
secure key names.
To assign a secure key to a cartridge:
1Enter the barcode of the cartridge. Separate multiple
barcodes with either spaces or commas.
2Select a secure key name from the list of available
names.
NOTE:Selecting None to will cause the library to
NOT use a secure key.
NOTE:The system must be offline to modify a
secure key.
PX720 DLTSage™ Tape Security Quick Start Guide
5
1Selecting Remove will remove the association between
the cartridge and a secure key name in the cartridge
database.
2Click Update to accept the changes.
Create Secure Key Name/
Secure Key Pair 0
Refer to figure 8 for information on Create Secure Key
Name/Secure Key Pair.
Figure 8 Create Secure Key
Name/Secure Key Pair
To create a secure key name/secure key pair:
1Enter the Secure Key Name.
2Enter a securekey in the protected Secure Key field.
3Enter the same secure key in the Verify Secure Key
field.
4Click New to create the secure key name/key pair.
Delete Secure Key Name 0
Refer to figure 9 for information on Delete Secure Key
Name.
NOTE:The secure key name must be less than 12
characters, may include spaces, but cannot
contain the following characters: ( ) = ;
NOTE:The Secure Key must be at least 8 characters
and no more than 32 characters.
Figure 9 Delete Secure Key Name
The Secure Key Names maintained on the library are
displayed in one of three lists:
•Unused Secure Keys - keys not associated with any
cartridges or tape drives currently in the system.
•Inactive Secure Keys - keys associated with cartridges
in the library, or currently assigned to the library, but
not assigned to any tape drives.
•Active Secure Keys - keys currently assigned to a tape
drive.
To de l et e a Secure Key Name/Secure Key pair from the
library:
1Select the desired Secure Key Names from the
available lists.
2Click Delete.
A confirmation message will be displayed, click Yes to
continue.
Any tape drives that have been secure key enabled will
remain enabled, but the secure key will not be used to
read or write cartridges.
Backup Secure Key File 0
Refer to figure 10 for information on Backup Secure Key
File.
Figure 10 Backup Secure Key File
PX720 DLTSage™ Tape Security Quick Start Guide
6
The list of Secure Key Name/Secure Key Pairs maintained
on the library should be backed up to a local device
whenever a change is made to the security keys.
1Enter and verify the Encryption Key.
The Encryption Key is required when restoring the
backup secure key file to any library.
2Click Save As...
The browser displays a download link.
3Right-click on the download link and select Save As...
to select a path and name the file.
4Click OK.
Upload Secure Key File 0
Refer to figure 11 for information on Upload Secure Key
File.
Figure 11 Upload Secure Key File
A file containing a list of Secure Key Name/Secure Key
Pairs can be restored to the library.
To upload (restore) a Secure Key File:
1Enter the encryption key of the original library.
2Enter the path and file name of the file to be uploaded
(click Browse...)
3Click Upload button.
A progress window is displayed indicating when the
upload is complete or if any errors occurred during the
upload or restoration of the file.
NOTE:Note the library's Encryption Key. The
Encryption Key is required when restoring the
file to any library.
NOTE:The user defined encryption key of the library
originally maintaining the list is required to
restore the file.
The Secure Key page is refreshed listing restored
secure keys.
Importing Secured Tape Cartridges 0
If you need to import tape cartridges into your library which
have been secured with a key from another PX720 library,
you need to import the secure key before the library can
read or write to the tape cartridges.
To import secured tapes:
1Insert the tape cartridges into the PX720 library (refer
to the PX720 User’s Guide (PN 6444601) for
information on inserting tape cartridges.
2On the PX720 library where the tape cartridges were
originally secured with a key, backup the specific secure
key associated with those tape cartridges (see Backup
Secure Key File).
3Upload the secure key from the original library to the
library where the tape cartridges were imported (see
Upload Secure Key File).
The imported tape cartridges are now associated with
the secure key.
NOTE:An error is displayed if the encryption key
provided does not match the encryption key used
to encode the secure keys.
PX720 DLTSage™ Tape Security Quick Start Guide
United States of America
Quantum Corporation
141 Innovation Drive
Irvine, CA 92612
U.S.A.
phone 949.856.7800
fax 949.856.7799
European Headquarters
Quantum Corporaton
3 Bracknell Beeches
Old Bracknell Lane West
Bracknell
Berkshire RG12 7BW
United Kingdom
phone +44 1344 353500
fax +44 1344 353510
Asia Pacific
Quantum Corporation
9 Temasek Boulevard, #08-03
Suntec Tower Two
Singapore 038989
Tel: +65 6334 0660
Fax: +65 6432 2830
Email: [email protected]
©2006 Quantum Corporation. Quantum, the Quantum logo, and the DLTtape logo are all registered trademarks of Quantum Corporation. SDLT and Super DLTtape are trademarks of
Quantum Corporation. Other trademarks may be mentioned herein which belong to other companies.
81-81588-02 A01 October 2006
Secure Key Maintenance 0
Quantum strongly recommends that you backup your
secure keys whenever a new key is added (see Backup
Secure Key File). The location of these keys should be
available to library administrators who need access to
secured tape cartridges.
CAUTION:If the secure key information is lost, any tape
cartridges that were secured with the lost
key will be unavailable for reading or writing.
Andere Handbücher für PX720
2
Inhaltsverzeichnis
Andere Quantum Lagerung Handbücher
Quantum
Quantum Atlas V Bedienungsanleitung
Quantum
Quantum Fireball LCT20 Bedienungsanleitung
Quantum
Quantum Scalar LTFS Gebrauchs- und Pflegehandbuch
Quantum
Quantum P4000 Series Bedienungsanleitung
Quantum
Quantum DXi4601 Bedienungsanleitung
Quantum
Quantum DLT Series Montageanleitung
Quantum
Quantum Scalar i6000 Bedienungsanleitung
Quantum
Quantum DLT-V4 Bedienungsanleitung
Quantum
Quantum DLTtape DLT 4000 Bedienungsanleitung
Quantum
Quantum Quantum Fireball SE Bedienungsanleitung
Quantum
Quantum PX500 Series Bedienungsanleitung
Quantum
Quantum ValueLoader LTO-2 Bedienungsanleitung
Quantum
Quantum DXi4520 Bedienerhandbuch
Quantum
Quantum Scalar 50 Leitfaden
Quantum
Quantum DLTtape SDLT 220 Handbuch
Quantum
Quantum Scalar i40 Bedienungs- und Sicherheitshinweise
Quantum
Quantum Quantum Bigfoot CY Bedienungsanleitung
Quantum
Quantum DLT-S4 Bedienungsanleitung
Quantum
Quantum LTO 2U Merkblatt
Quantum
Quantum DPM 5500 Bedienungsanleitung
Beliebte Lagerung Handbücher anderer Marken
Spectra Logic
Spectra Logic T-Series Spectra T50e Bedienungsanleitung
Panasonic
Panasonic LKM-F931-1 Bedienungsanleitung
Tabernus
Tabernus Enterprise Erase E2400 Bedienungsanleitung
Rocstor
Rocstor COMMANDER 3F series Bedienungsanleitung
HP
HP P9000 Bedienungsanleitung
Western Digital
Western Digital Ultrastar Data60 Bedienungsanleitung