Quantum StorNext QD7000 Bedienungsanleitung

Changing Host Protocol in Base

System

StorNext QD7000

Firmware 8.30.xx.xx

6-68568-01 Rev A

ii Changing Host Protocol in Base System

Changing Host Protocol in Base System, 6-68568-01 Rev A, April 2017 Product of USA.

Quantum Corporation provides this publication “as is” without warranty of any kind, either express or implied, including but not

limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this

publication from time to time without notice.

Your right to copy this manual is limited by copyright law. Making copies or adaptations without prior written authorization of

Quantum Corporation is prohibited by law and constitutes a punishable violation of the law.

TRADEMARK STATEMENT

Artico, Be Certain (and the Q brackets design), DLT, DXi, DXi Accent, DXi V1000, DXi V2000, DXi V4000, DXiV-Series, FlexTier,

Lattus, the Q logo, the Q Quantum logo, Q-Cloud, Quantum (and the Q brackets design), the Quantum logo, Quantum Be Certain

(and the Q brackets design), Quantum Vision, Scalar, StorageCare, StorNext, SuperLoader, Symform, the Symform logo (and

design), vmPRO, and Xcellis are either registered trademarks or trademarks of Quantum Corporation and its affiliates in the United

States and/or other countries. All other trademarks are the property of their respective owners. Products mentioned herein are for

identification purposes only and may be registered trademarks or trademarks of their respective companies. All other brand names

or trademarks are the property of their respective owners. Quantum specifications are subject to change.

Changing Host Protocol in Base System iii

Preface

Note: The 8.30.xx.xx firmware (Lehigh) is used in the QD7000 (E5600,

Titan RAID controller, only). Refer to the NetApp to Quantum

Naming Decoder section for additional information.

This section provides the following information:

•Audience

•Prerequisites

•NetApp to Quantum Naming Decoder

•Product Safety Statements

•Contacts

•Comments

•Quantum Global Services

Audience This manual is intended for storage customers and technicians.

Preface

iv Changing Host Protocol in Base System

Prerequisites Prerequisites for installing and using this product include knowledge of:

• Servers and computer networks

• Network administration

• Storage system installation and configuration

• Storage area network (SAN) management and direct attach storage

(DAS)

• Fibre Channel (FC) and Ethernet protocols

NetApp to Quantum

Naming Decoder

Use Table 1 to correlate the NetApp product nomenclature to the

equivalent Quantum-storage naming conventions.

Table 1 Product Nomenclature

E-Series NetApp

Product Quantum-Storage Description

Controller-Drive Tray Base System Quantum uses Base System when referring to a drive

tray with the RAID controllers.

Drive Tray Expansion Unit Quantum uses Expansion Unit when referring to a

drive tray with the environmental services modules

(ESMs).

E5600 (Code Name:

Titan)

RAID Controller Four 16Gb/s FC SFP+ host ports

E5500 (Code Name:

Soyuz)

RAID Controller Four 16Gb/s FC SFP+ host ports

E5400 (Code Name:

Pikes Peak)

RAID Controller Four 8Gb/s FC SFP+ host ports

DE6600 (Code Name:

Wembley)

4U 60-drive

enclosure

Sixty 3.5 inch disk drives

Preface

Changing Host Protocol in Base System v

E5560 or E5660

(DE6600 4U drive

enclosure with

E5500 or E5600 RAID

controllers)

Quantum StorNext

QD7000

E5460

(DE6600 4U drive

enclosure with

E5400 RAID

controllers)

Quantum StorNext

QD6000

E5424

(DE5600 24-drive 2U

drive enclosure

(Code Name:

Camden with E5400

RAID controllers)

Quantum StorNext

QS2400

E5412

(DE1600 12-drive 2U

drive enclosure

(Code Name: Ebbets

with E5400 RAID

controllers)

Quantum StorNext

QS1200

E-Series NetApp

Product Quantum-Storage Description

Preface

vi Changing Host Protocol in Base System

Product Safety

Statements

Quantum will not be held liable for damage arising from unauthorized

use of the product. The user assumes all risk in this aspect.

This unit is engineered and manufactured to meet all safety and

regulatory requirements. Be aware that improper use may result in

bodily injury, damage to the equipment, or interference with other

equipment.

WARNING: Before operating this product, read all instructions and

warnings in this document and in the system, safety, and

regulatory guide.

Preface

Changing Host Protocol in Base System vii

Contacts For information about contacting Quantum, including Quantum office

locations, go to:

http://www.quantum.com/aboutus/contactus/index.aspx

Comments To provide comments or feedback about this document, or about other

Quantum technical publications, send e-mail to:

[email protected]

Preface

viii Changing Host Protocol in Base System

Quantum Global

Services

Accelerate service issue resolution with these exclusive Quantum

StorageCare services:

•Service and Support Website - Register products, license software,

browse Quantum Learning courses, check backup software and

operating system support, and locate manuals, FAQs, firmware

downloads, product updates and more in one convenient location.

Benefit today at:

http://www.quantum.com/serviceandsupport/get-help/

index.aspx#contact-support

•eSupport - Submit online service requests, update contact

information, add attachments, and receive status updates via email.

Online Service accounts are free from Quantum. That account can

also be used to access Quantum’s Knowledge Base, a

comprehensive repository of product support information. Get

started at:

http://www.quantum.com/customercenter/

For further assistance, or if training is desired, contact the Quantum

Customer Support Center:

North America 1-800-284-5101 (toll free)

+1-720-249-5700

EMEA +800-7826-8888 (toll free)

+49-6131-324-185

APAC +800-7826-8887 (toll free)

+603-7953-3010

For worldwide support:

http://www.quantum.com/serviceandsupport/get-help/

index.aspx#contact-support

E-Series and EF-Series

Changing the Host Protocol in the E5600 or EF560 by

Replacing Hardware Components

When you change the host protocol of an E5612, E5624, or E5660 storage array or an EF560 flash array by replacing hardware

components, you must power off the storage array or flash array, remove hardware, install new hardware, and reapply power.

Before starting the procedure, be aware of the following:

• You must review the information in

Understanding the options for changing the host protocol

on page 2 to learn about the

different methods for changing the host protocol and to confirm that you are using the correct instructions for your situation.

• Because the power must be off when you upgrade hardware to change the host protocol, you must schedule a downtime

maintenance window for this procedure. You cannot access data on the storage array or flash array until you have

successfully completed the upgrade.

• You must obtain any new cables, transceivers, switches, and host bus adapters (HBAs) needed for the new host protocol. You

must install any new host hardware before you can connect the storage array or flash array to the hosts.

Attention: After installing the new hardware, you must inform NetApp technical support about the change to the hardware

configuration by sending an upgrade notification. This notification ensures that you receive correct replacement parts if you

need them later.

Steps

1. Understanding the options for changing the host protocol on page 2

2. Determining the Replacement Part Number on page 3

3. Procedures for changing the host protocol on page 3

4. Managing Data Assurance on page 6

5. Managing Synchronous Mirroring on page 7

6. Managing Asynchronous Mirroring on page 7

7. Cabling considerations on page 7

8. Preparing to upgrade hardware on page 8

9. Powering down on page 10

10. Removing the controller canisters on page 11

11. Removing the HICs (if upgrading only the HICs) on page 15

12. Installing the new HICs (if upgrading only the HICs) on page 16

13. Replacing the controller canisters on page 17

14. Reconnecting the cables on page 17

15. Applying power on page 17

16. Restoring the drive security key (if replacing controller canisters) on page 18

17. After upgrading the hardware on page 18

18. Sending an upgrade notification to NetApp on page 19

Related information

NetApp E-Series and EF-Series Systems Documentation Center

NetApp Downloads

NetApp Interoperability Matrix Tool

Web: www.netapp.com • Feedback: [email protected]

Understanding the options for changing the host protocol

Review the options for changing the host protocol in an E5600 storage array or an EF560 flash array to confirm that you are

following the correct steps.

The following figure provides a high-level overview of the options for changing the host protocol of an E5600 storage array or

an EF560 flash array.

Key Option Description

Hardware

upgrade You must replace hardware to change the protocol.

Note: For most hardware upgrades, you need to replace only the HICs;

however, if you currently use iSCSI, Fibre Channel, or Fibre Channel-

iSCSI split protocol, you might need to replace the controller canisters,

which include the HICs. The exact procedure you need to follow depends

on your Replacement Part Number. Refer to

Determining the Replacement

Part Number

on page 3.

Software

feature pack

conversion

You can apply a software feature pack in SANtricity Storage Manager to

change the protocol.

Important: This document does not describe how to perform software

feature pack conversions. For those instructions, use one of the documents

listed at the end of this topic.

As the figure indicates, there are three methods for changing the host protocol. You might need to:

• Upgrade hardware components (the paths shown with the solid, blue arrows)

• Perform a software feature pack conversion (the paths shown with the dotted, green arrows)

• Perform both a hardware upgrade and a feature pack conversion. For example, if you want to change the protocol from SAS

to Infiniband (IB), and you want to use iSCSI RDMA Protocol (SRP) instead of iSCSI Extensions for Remote Direct

Memory Access (iSER), you must follow a two-step process:

1. Upgrade the hardware to change the HICs from SAS to IB-iSER (this is the IB HIC's default protocol).

2Changing the Host Protocol in the E5600 or EF560 by Replacing Hardware Components

Andere Handbücher für StorNext QD7000

Inhaltsverzeichnis

Andere Quantum Lagerung Handbücher

Quantum

Quantum StorNext QD7000 Bedienungsanleitung

Quantum

Quantum Scalar i500 Bedienungsanleitung

Quantum

Quantum DLTtape DLT 2000 Handbuch

Quantum

Quantum Scalar i40 Bedienungsanleitung

Quantum

Quantum Superloader 3 Bedienungsanleitung

Quantum

Quantum LTO3 A-Series Bedienungsanleitung

Quantum

Quantum P4000 Series Bedienungsanleitung

Quantum

Quantum DXi6900-S Bedienungsanleitung

Quantum

Quantum DLT 4700 Bedienungsanleitung

Quantum

Quantum StorNext QS1200 Bedienungsanleitung

Quantum

Quantum Scalar i6000 Technisches Handbuch

Quantum

Quantum Scalar i2000 Bedienungsanleitung

Quantum

Quantum ValueLoader DLT VS80 Betriebsanleitung

Quantum

Quantum Scalar i6000 Bedienungsanleitung

Quantum

Quantum ATL 7100 Bedienungsanleitung

Quantum

Quantum ValueLoader DLT VS160 Bedienungsanleitung

Quantum

Quantum StorNext QD7000 Bedienungsanleitung

Quantum

Quantum DXi4700 Installations- und Betriebshandbuch

Quantum

Quantum DLTtape SDLT 600 Bedienungsanleitung

Quantum

Quantum ACL 4/52 Bedienungsanleitung

Quantum

Quantum ValueLoader LTO-1 Bedienungsanleitung

Quantum

Quantum StorNext QM1200 Bedienungsanleitung

Quantum

Quantum Superloader 3 Bedienungsanleitung

Quantum

Quantum Scalar 50 Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung