QUINN 57460 Montageanleitung
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back
of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep
this manual and the receipt in a safe and dry place for future reference. 21a
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2020 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product
described herein. Tools required for assembly and service may not be included.
Read this material before using this
product. Failure to do so can result in
serious injury. SAVE THIS MANUAL.
Page 2 For technical questions, please call 1-888-866-5797. Item 57460
Specifications
Display Units Inches & Millimeters
Accuracy ±0.001" (0.02mm)
Display 0.0005" (0.01mm)
Power Supply CR2032 Button Battery (Included)
IMPORTANT SAFETY INFORMATION
1. Keep out of your child’s reach. Discard
button batteries carefully. Do not allow
children to play with devices that contain
button batteries. This product is not a toy.
2. Wear ANSI-approved safety goggles during use.
3. Keep work area clean and well lit.
4. Do not operate when tired or when under the
influence of alcohol, drugs or medication.
5. Use as intended only.
6. Inspect before every use; do not use
if parts are loose or damaged.
7. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
Components and Controls
ON/OFF Button
in/mm Button
Prongs
ZERO/ABS Button
Battery Cover
Origin Button
Page 3For technical questions, please call 1-888-866-5797.Item 57460
Operation Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before use of this product.
1. Push the OFF ON button to turn caliper on.
2. To toggle measurement between inches
and millimeters, press in/mm button.
3. With jaws closed, press ZERO
to set readout to 0.00.
4. To measure outside of object, set the bottom
prongs outside object being measured. Slide the
jaws together until they gently contact the item.
Figure A: Outer Measurement
5. To measure inside of object, set the top prongs
inside object being measured. Spread prongs
apart until they touch surface of object.
Figure B: Inner Measurement
6. To measure an object’s step, place the sliding
jaw on the upper step of the workpiece,
then spread the prongs apart until the
fixed jaw contacts the lower step.
Figure C: Step Measurement
Note: Use the ORIGIN button to set the Caliper
to its absolute origin. Press and hold button
for 1.5 seconds until readout shows 0.00.
7. When finished, press OFF ON
button to turn off Caliper.
8. To replace battery, open battery compartment
to right of display, install new CR2032
battery positive (flat) side up, and slide
Battery Cover back into place.
Record Serial Number Here:
Note: If product has no serial number, record
month and year of purchase instead.
Note: Replacement parts are not available.
Reference UPC 193175412133
Page 4 For technical questions, please call 1-888-866-5797. Item 57460
26541 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED
TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability
standards, and warrants to the original purchaser that this product is free from defects in materials
and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to
damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside
our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent,
special or consequential damages arising from the use of our product. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion
may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Andere QUINN Messgerät Handbücher
