Radio Shack TAD-1006 Bedienungsanleitung

Cat. No. 43-768

OWNER’S MANUAL

Please read before using this equipment.

TAD-1006

Digital Answering System Telephone

with Time/Day Stamp

43-768.fm Page 1 Friday, August 13, 1999 2:49 PM

FEATURES

Your TAD-1006 Digital Answering

System Telephone with Time/Day

Stamp is a sophisticated, fully digital

message center that combines a tele-

phone and an answering machine in

one convenient package.

Fully digital means the TAD-1006

stores all messages on a computer

chip. This gives you advanced capa-

bilities over tape-based answering

machines. For example, you can save

individual messages while the rest are

deleted.

And, because your TAD-1006 is fully

digital, there are no tape mechanisms

to wear out and no tapes to bother

with.

TELEPHONE

13-Number Memor

Dialin

— lets

you store up to 13 phone numbers in

memory for easy dialing — three prior-

ity (one-touch) numbers and ten stan-

dard numbers.

Redial — lets you quickly dial the last

number dialed.

Touch Tone (DTMF) or Pulse Dial-

— lets you use the phone with ei-

ther type of dialing.

Hearin

Aid Compatible — lets you

use this phone with hearing aids that

have a T (telephone) switch.

TAD

/Time Stamp — records the day

and time each message was record-

ed.

itall

-S

nthesized Voice —

guides you through operation of the

TAD-1006.

Built-In Announcements — let you

immediately begin using the TAD-

1006 to answer calls and record mes-

sages.

Announcement-Onl

— lets you set

the TAD-1006 to play a message for

the caller, then automatically hang up

without letting the caller leave a mes-

sage.

Messa

e Protection — prevents you

from accidentally deleting a message

while it plays the first time.

Data Compression — automatically

compresses periods of silence to al-

low up to 16 minutes of message stor-

age.

ustable Number of Rin

s— lets

you set the TAD-1006 to answer after

anywhere from one to nine rings.

Call Screenin

— lets you listen as a

caller leaves a message so you can

decide whether or not to answer the

call.

Radio Shack is a registered trademark used by Tandy Corporation.

43-768.fm Page 2 Friday, August 13, 1999 2:49 PM

Memo Recording — lets you leave

messages for yourself or others in

your home or office.

Two-Way Recording — lets you

record both sides of your phone con-

versation.

Room Monitor — lets you listen from

a remote phone to the room where the

TAD-1006 is installed.

Volume Control — lets you adjust the

TAD-1006’s speaker volume for mes-

sage playback.

Phone Pick-Up Detection — stops

recording when you pick up any

phone on the same line as the TAD-

1006, and resets to answer the next

call.

Remote Operation — lets you use a

touch-tone phone (or rotary phone

and pocket tone dialer) to operate the

TAD-1006 while you are away from

your home or office.

Programmable Remote Operation

Security Code — lets you set your

own 3-digit security code for remote

operation.

Remote Answer-On — lets you call

the TAD-1006 from a remote location

and set it to answer calls.

Toll-Saver — lets you avoid unneces-

sary toll charges when you call by

long-distance to check your messag-

es.

Outgoing Message Remote Skip —

stops playing your outgoing message

during remote operation as soon as

you press .

This system has been tested and

found to comply with all applicable UL

and FCC standards.

We recommend you record your sys-

tem’s serial number here. The number

is on the bottom of the TAD-1006.

Serial Number __________________

Warning: To prevent fire or shock haz-

ard, do not expose this product to rain

or moisture.

This symbol is intended to alert you

to the presence of uninsulated dan-

gerous voltage within the product’s

enclosure that might be of sufficient

magnitude to constitute a risk of

electric shock. Do not open the

product’s case.

This symbol is intended to inform

you that important operating and

maintenance instructions are in-

cluded in the literature accompany-

ing this product.

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED PERSONNEL.

CAUTION

43-768.fm Page 3 Friday, August 13, 1999 2:49 PM

READ THIS BEFORE

INSTALLATION

We have designed your system to

conform to federal regulations, and

you can connect it to most telephone

lines. However, each device that you

connect to the phone line draws pow-

er from the line. We refer to this power

draw as the device’s ringer equiva-

lence number, or REN. The REN is

shown on the bottom of your system.

If you are using more than one device

on the line, add up all the RENs. If the

total is more than five, your phone

might not ring or your system might

not answer. In rural areas, a total REN

of three might impair ringer operation.

If ringer operation is impaired, remove

one of the devices from the line.

FCC STATEMENT

Your system complies with Part 68 of

FCC Rules

. You must, upon request,

provide the FCC registration number

and the REN to your phone company.

Both numbers appear on the bottom

of your system.

Note: You must not connect your

system to:

• Coin-operated systems

• Party-line systems

• Most electronic key phone sys-

tems

This device compiles with Part 15 of

FCC Rules

. Operation is subject to the

following two conditions:

• This device may not cause harm-

ful interference.

• This device must accept any inter-

ference received, including inter-

ference that may cause

undesirable operation.

43-768.fm Page 4 Friday, August 13, 1999 2:49 PM

CONTENTS

Installation ............................................................................................................ 7

Selecting a Location ........................................................................................ 7

Connecting the AC Adapter ............................................................................ 7

Installing a Backup Battery ............................................................................. 8

Mounting the TAD-1006 .................................................................................. 9

Placing on a Desktop ................................................................................ 9

Connecting the Wall Bracket .................................................................... 9

Mounting on a Wall Plate ........................................................................ 10

Mounting Directly on the Wall ................................................................. 11

Connecting the Handset ............................................................................... 12

Setting the TONE-PULSE Switch ................................................................. 12

Telephone Operation ......................................................................................... 13

Using REDIAL ............................................................................................... 13

Using Tone Services on a Pulse Line ........................................................... 13

Using Memory Dialing ................................................................................... 13

Storing a Number in Memory .................................................................. 14

Storing a Pause in Memory .................................................................... 15

Dialing a Stored Number ........................................................................ 15

TAD Preparation ................................................................................................ 16

Turning the TAD On/Off ................................................................................. 16

Setting the Day and Time .............................................................................. 16

Setting the Number of Rings ......................................................................... 17

Recording Announcements ........................................................................... 18

Recording the Outgoing Announcement ................................................ 18

Checking/Deleting the Outgoing Announcement .................................... 19

Recording the Memory Full Announcement ........................................... 19

Checking/Deleting the Memory Full Announcement .............................. 19

TAD Operation ................................................................................................... 20

Setting the TAD to Answer/Not Answer Calls ............................................... 20

Answering Calls ...................................................................................... 20

Using the Announcement-Only Feature ........................................................ 21

Recording the Announcement-Only Message ........................................ 21

Turning Announcement-Only On/Off ...................................................... 21

Checking/Deleting the Announcement-Only Message ........................... 22

43-768.fm Page 5 Friday, August 13, 1999 2:49 PM

Screening Calls ............................................................................................. 22

Recording a 2-Way Conversation .................................................................. 22

Recording a Memo ........................................................................................ 23

Playing Messages ......................................................................................... 23

Playing Incoming Messages ................................................................... 24

Playing 2-Way Conversations ................................................................. 24

Playing Memos ....................................................................................... 24

Deleting Messages ........................................................................................ 25

Remote TAD Operation ...................................................................................... 26

Using the Toll-Saver ...................................................................................... 26

Changing the Remote Code .......................................................................... 26

Remote Answer-On ....................................................................................... 27

Using Remote Commands ............................................................................ 27

List of Remote Commands ..................................................................... 29

Problem Solving ................................................................................................. 30

Resetting the TAD-1006 ................................................................................ 32

Care and Maintenance ....................................................................................... 33

Lightning ........................................................................................................ 34

43-768.fm Page 6 Friday, August 13, 1999 2:49 PM

INSTALLATION

Important: To be sure your TAD-1006

works properly, follow this sequence

to install it.

1. Select a location (see “Selecting a

Location”).

2. Connect the AC adapter (see

“Connecting the AC Adapter”).

3. Install a backup battery (see

“Installing a Backup Battery” on

Page 8).

4. Mount the TAD-1006 (see “Mount-

ing the TAD-1006” on Page 9).

5. Connect the handset (see “Con-

necting the Handset” on Page 12).

6. Set the TONE-PULSE switch (see

“Setting the TONE-PULSE

Switch” on Page 12).

SELECTING A

LOCATION

Select a location for the TAD-1006

that is near a modular phone jack and

an AC outlet, and out of the way of

normal activities. You can place the

TAD-1006 on a flat surface (such as a

desktop or counter-top), mount it on a

modular jack wall plate, or mount it di-

rectly on the wall.

Notes:

• If the phone line jack is not a mod-

ular jack, you must update the wir-

ing. You can convert the wiring

yourself, using jacks and adapters

available at any Radio Shack

store. Or, you can let the phone

company update the wiring for

you.

• The phone company will charge

you for the installation of neces-

sary jacks.

• The USOC number of the jack to

be installed is RJ11C for a base-

board jack or RJ11W for a wall-

plate jack.

CONNECTING THE AC

ADAPTER

Caution: You must use a Class II AC

adapter that supplies 12 volts of pow-

er, delivers at least 200 milliamps, and

has a plug that properly fits the TAD-

1006’s 12V DC jack with its center tip

set to negative. The supplied adapter

meets these specifications. Using an

adapter that does not meet these

specifications could damage the

adapter and the TAD-1006.

1. Insert the small round plug of the

supplied AC adapter into the 12V

DC jack, then press the adapter’s

cord into the strain-relief slot on

the bottom of the TAD-1006.

illustration

43-768.fm Page 7 Friday, August 13, 1999 2:49 PM

2. Plug the other end of the AC

adapter into a standard AC outlet.

The TAD-1006 initializes, the L.

BATT (low battery) indicator lights

steadily, and the ANSWER,

MEMO, and PLAY indicators flash

six times. Then the TAD-1006

beeps once and the ANSWER

indicator lights steadily.

Notes:

• Be sure not to press any of the

TAD-1006’s buttons while you are

plugging the adapter into the AC

outlet. If you accidentally press a

button, unplug the adapter from

the AC outlet, then plug it back in.

• The answering system on your

TAD-1006 cannot operate without

AC power. However, you can

make and answer calls on the

telephone without AC power.

INSTALLING A BACKUP

BATTERY

If AC power fails or you unplug the

TAD-1006, a 9V backup battery (not

supplied) saves the messages and the

settings for the day, time, and security

code. We recommend you use an al-

kaline battery, such as Radio Shack

Cat. No. 23-553.

1. To open the battery compartment

cover on the bottom of the TAD-

1006, loosen the screw in the

cover with a small Phillips screw-

driver, then lift off the cover.

2. Snap the battery’s contacts firmly

to the battery connector, then put

the battery into the compartment.

3. Replace the cover, then tighten

the screw.

illustration

43-768.fm Page 8 Friday, August 13, 1999 2:49 PM

Replace the battery if the L.BATT (low

battery) indicator turns on while the

AC adapter is properly connected.

Cautions:

• Before you replace the battery, be

sure the supplied adapter is

securely connected to an AC out-

let and to the jack on the back of

the TAD-1006. Otherwise, you

might lose any stored information.

• Always use a fresh battery of the

required size and type.

• Dispose of the battery promptly

and properly. Do not bury or burn

it.

MOUNTING THE

TAD-1006

Placing on a Desktop

1. Plug one end of the supplied mod-

ular cord into the TO LINE jack on

the back of the TAD-1006.

2. Plug the modular cord’s other end

into a modular phone line jack.

Connecting the Wall Bracket

If you plan to mount the TAD-1006 on

a modular jack wall plate or directly on

the wall, you must first connect the

supplied mounting bracket to the back

of the TAD-1006. To connect the

bracket, insert the tabs on the bracket

into the slots closest to the battery

compartment, then press the bracket

to the phone until it snaps into place.

To remove the bracket after attaching

it, simply press in the tab on each side

of the bracket and lift the bracket away

from the TAD-1006.

illustration

43-768.fm Page 9 Friday, August 13, 1999 2:49 PM

Mounting on a Wall Plate

1. Plug one end of the supplied mod-

ular cord into the TO LINE jack on

the back of the TAD-1006.

2. As shown below, press the modu-

lar cord into the right groove on

the mounting bracket and press

the AC adapter’s cord into the left

groove.

3. Plug the other end of the modular

cord into the modular wall plate.

4. Line up the keyhole slots on the

bracket with the studs on the wall

plate, then slide the TAD-1006

down onto the wall plate until it is

secure.

5. Press up on the handset holder to

remove it, turn it over so its tabbed

edge faces up, then press it back

down into its slot on the base.

illustration

43-768.fm Page 10 Friday, August 13, 1999 2:49 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Radio Shack Anrufbeantworter Handbücher

Radio Shack

Radio Shack 900MHz Bedienungsanleitung

Radio Shack

Radio Shack TAD-759 Bedienungsanleitung

Radio Shack

Radio Shack 43-3880 Bedienungsanleitung

Radio Shack

Radio Shack 43-3888 Bedienungsanleitung

Radio Shack

Radio Shack TAD-799 Bedienungsanleitung

Radio Shack

Radio Shack TAD-764 Bedienungsanleitung

Radio Shack

Radio Shack TAD -797 Bedienungsanleitung

Radio Shack

Radio Shack TAD-3806 Bedienungsanleitung

Radio Shack

Radio Shack TAD-1005 Bedienungsanleitung

Radio Shack

Radio Shack TAD-1029 Bedienungsanleitung

Radio Shack

Radio Shack 43-3801 Bedienungsanleitung

Radio Shack

Radio Shack 43-3822 Bedienungsanleitung

Radio Shack

Radio Shack Digital Answering System with Big Button Trim... Bedienungsanleitung

Radio Shack

Radio Shack TAD-1018 Bedienungsanleitung

Radio Shack

Radio Shack TAD-1027 Bedienungsanleitung

Radio Shack

Radio Shack TAD-277 Bedienungsanleitung

Radio Shack

Radio Shack TAD-1009 Bedienungsanleitung

Radio Shack

Radio Shack 900MHz Bedienungsanleitung

Radio Shack

Radio Shack TAD-704 Bedienungsanleitung

Radio Shack

Radio Shack TAD-285 Bedienungsanleitung

Radio Shack

Radio Shack 14 Minute Bedienungsanleitung

Radio Shack

Radio Shack 43-3803 Bedienungsanleitung

Radio Shack

Radio Shack TAD-716 Bedienungsanleitung

Radio Shack

Radio Shack TAD-795 Bedienungsanleitung

Beliebte Anrufbeantworter Handbücher anderer Marken

AT&T

AT&T 2455 Bedienungsanleitung

Panasonic

Panasonic KX-TG2583CB Bedienungsanleitung

Panasonic

Panasonic KX-TGE820E Bedienungsanleitung

BellSouth

BellSouth GH9488 Sicherheitsleitfaden

GE 2-9985 Bedienungsanleitung

Panasonic

Panasonic KX-TG2631 Bedienungsanleitung

Panasonic

Panasonic KX-TCD961CXB Bedienungsanleitung

AT&T

AT&T 1717 Bedienungsanleitung

Alcatel

Alcatel TEMPORIS 55-CE Bedienungsanleitung

AT&T

AT&T E2562 Bedienungsanleitung

Telstra

Telstra Monitor 420 Bedienungsanleitung

Kortex

Kortex IAM V90 Bedienungsanleitung

Panasonic

Panasonic EASA-PHONE KX-T1451 Bedienungsanleitung

Philips

Philips VOIP8551B/05 Bedienungsanleitung

Topcom

Topcom LUCCA Answering Machine Bedienungsanleitung

Panasonic

Panasonic KX-TGM420 Bedienungsanleitung

Panasonic

Panasonic KX-TCD320E Bedienungsanleitung

TIPTEL

TIPTEL Ergophone 307 Bedienungsanleitung