Radio Shack 43-3905 Bedienungsanleitung

43-3905

User’s Guide

Caller ID Wall Phone

Thank you for purchasing your Caller ID Wall Phone from

RadioShack. Please read this user’s guide before installing,

setting up, and using your new phone.

2/3

Package contents

• CallerIDWallPhone • LongPhoneCord

• ShortPhoneCord • CoiledCord

• User’sGuide • QuickStart

Features

• CallerIDmemorystoresinformationforupto99calls

• CallerID/CallWaitingIDdisplayshowswho’scalling

• Backlitdisplaysforbettervisibilityatnightorinlowlight

• Traditionalmetalbellringer

• Heavydutydesign

1Install Batteries

1. Liftthebatterycompartmentcoverfromthetopofthe

base,thenremove

thecompartment.

2. InsertfourAA

batteriesintothe

compartmentas

indicatedbythe

polaritysymbols

(+and–)marked

inside.

3. Replacethebattery

compartmentand

cover.

bBattery Notes:

• Duringbatteryreplacement,keepthelinecordpluggedinand

replace the batteries within two minutes to maintain Caller ID

memory.

• Whenthelowbatteryiconappearsorthedisplaydims,replacethe

batteries.

• Makesurethebatteriesttightlyinthebatterycompartment.

• Disposeofoldbatteriespromptlyandproperly.

• Donotburnorburybatteries.

• Useonlyfreshbatteriesoftherequiredsizeandrecommended

type.

• Donotmixoldandnewbatteries,differenttypesofbatteries

(standard, alkaline, or rechargeable), or rechargeable batteries of

different capacities.

• Ifyoudonotplantousethephonefortwoweeksorlonger,

remove the batteries. Batteries can leak chemicals that can destroy

electronic parts.

2Install Your Phone

Youcanmountyourphoneonawallplate,awall,orplaceiton

adeskortable.

To mount the phone to a wall plate:

1. Plugoneendofthe

suppliedshortmodularcord

intotheLINEjackatthe

backofthebase.

2. Plugtheotherendofthe

cordintothewallplatejack.

3. Alignthebase’skeyhole

slotswiththewallplate

studsandslidethephone

downwardtosecureit.

To mount the phone directly on a wall:

1. Drilltwoholes3.25inches(83mm)apart,onebelowthe

other.

2. Threadascrewinto

eachhole,lettingthe

headsextendabout

0.2inch(5mm)from

thewall.

3. Plugoneendof

thesuppliedlong

modularcordintothe

LINEjackattheback

ofthebase.

4. Alignthebase’s

keyholeslotswiththe

installedscrewsandslidethephonedownwardtosecureit.

Toconnectthehandset,plugoneendofthesuppliedcoiled

cordintothehandset’smodularjack.Thenconnectittothejack

ontheleftbottomofthebase.

nNotes:

• YourlocalRadioShack store sells a variety of longer coiled handset

cords, which are especially useful when you mount the phone on a

wall.

• Ifyourhomehasspeciallywiredalarmequipmentconnectedto

the telephone line, ensure the installation of this system does not

disableyouralarmequipment.Ifyouhavequestionsaboutwhat

willdisablealarmequipment,consultyourtelephonecompanyor

aqualiedinstaller.

• Selectalocationforyourtelephonethatisnearatelephonejack

and not in the way of normal activities in the area.

• Yourtelephoneconnectsdirectlytoamodulartelephoneline

jack.Ifyourtelephonewiringdoesnothaveamodularjack,you

canupdatethewiringyourselfusingjacksandadapters(available

0.2”(5mm)

3.25”

(83mm)

DELETE

ErasesCallerID

information.

CALL BACK

Callsbackthenumber

shownonCallerID.

UP/DOWN

ScrollthroughCallerID

records.

M/S (Master/Secondary)

SettoM.

TONE/PULSE

Setthedialmodefor

yourphonesystem.

VOLUME NORM/HI

Setthecallvolumelevel.

RINGER OFF/LO/HIGH

Settheringervolumeor

turntheringeroff.

NEW

Flasheswhenyouhave

newcalls.

3-line Display

Showsname,

number,dateand

timeofincoming

calls.

at your local RadioShack store), or have the telephone company

updatethewiringforyou.Youmustusecompatiblemodularjacks

thatarecompliantwithPart68ofFCCRulesandtherequirements

adopted by the ACTA. The telephone cord and modular plug

provided is Part 68 compliant for connecting to the telephone

company network.

3Set Phone Options

Phone Settings

1. HolddownbothUPandDOWNforaboutfourseconds

untilENTER LANGUAGE,thenENG ESP FRAappear,with

ENGashing.

2. PressUPorDOWNtoselectthedesiredlanguage,then

pressDELETEtoconrm.LCD CONTRASTand1 2 3 4 5

appearonthedisplay,with3ashing.

3. PressUPorDOWNtoselectthecontrastlevel(1-5),and

pressDELETEtoconrm.ENTER AREA CODEappears,then

___appears,withtherst_ashing.

4. PressUPorDOWNtoselecttherstnumberofthearea

code,andpressDELETEtoconrmtheselection.The

ashing_goestothenextdigit.

5. Repeatstep4tosetthesecondandthirddigits.

Ringer

Ifyoudonotwanttohearthephonering,slideRINGERto

OFF.Youcanstillmakecallswiththeringeroff,andyoucanstill

answercallsifyouhearanotherphoneonthesamelinering.If

youwanttohearthephonering,setRINGERtoHIorLO.

Dial Mode

SlideTONE/PULSEtothesettingforthetypeofdialingservice

youhave.Ifyouarenotsurewhichtypeyouhave,dothis

simpletest.

1. SlideTONE/PULSEtoTONE.Liftthehandsetandlistenfor

adialtone.

2. Pressanynumberexcept0.(Ifyoursetuprequiresthatyou

dialanaccesscode,usually 9,beforeyoudialanoutside

number,donotpresstheaccesscodenumber.)

• Ifthedialtonestops,youhavetouchtoneservice.Keep

theswitchonTONE.

• Ifthedialtonecontinues,youhavepulseservice.Set

theswitchtoPULSE.

Using Special Tone Services

Somecomputerservicesrequiretonesignalsforcommunications.

Ifyouhavepulseservice,youcanstillsimulatetonesignalsby

followingthesesteps.

1. Connecttothespecialserviceusingpulsedialing.

2. Whenthespecialserviceanswers,press*totemporarily

switchtotonedialing.

3. Whenyoucompletethecall,hanguptochangethesetting

backtoPULSE.

Master/Secondary Setting

Formodernphonessystems,slideM/Sto M.

nNotes:

• IfyouhaveotherphoneswithaMaster/Secondaryswitch,setthem

to S.Setonesystemtoanswerandsettheotherstooff.

• IfMis not set on at least one phone, incoming calls might be

disconnected.

• DonotconnectmorethanfourCallerIDmodules(includingthis

phone) that do not have Call Waiting to the same phone line.

• IfyouconnectanothertypeofCallerIDmodulethathasCall

Waiting to the same phone line as your system, the Call Waiting

signal might be garbled or not received.

Operation

Making a Call

1. Pickupthehandsetandwaitforadialtone.

2. Usethekeypadtoenterthenumberyouwishtodial.The

numberappearsonthedisplay.

3. Whenyoucompleteyourcall,hangupthehandset.Afew

secondslater,thenumberdisappears,andthedisplay

returnstonormal.

nNote: If you dial a number over 15 digits, only the last 14

digits appear on the display.

Receiving a Call

Whenyoureceiveacall,thephoneringsandtheNEW indicator

ashes.CALL#andthecaller’snumberappearonthedisplay.To

answerthecall,pickupthehandset.

Timer

Thisphoneisdesignedwithaclocktimertocounttheoff-

hooktimeinseconds,uptoonehour.Thetimerappearson

thedisplayandstartstocountupwhenyoudialanumberor

answeranincomingcall.

nNote: If you lift the handset and don’t dial a number, the timer

appears and starts to count up after 10 seconds.

Using Flash

IfyouhaveCallWaiting,pressFLASHtoansweranincoming

callwithoutdisconnectingthecurrentcall.PressFLASHagain

toreturntotherstcall.

nNote: If you do not have Call Waiting, pressing FLASH might

disconnect the current call.

Using Redial

Toredialthelastnumberyoucalled,pickupthehandsetand

press REDIALwhenyouhearadialtone.Thenumberscrolls

acrossthedisplay,andthephoneautomaticallydialsit.

nNote: The redial memory holds up to 32 digits, so you can redial

long distance as well as local phone numbers.

Using Pause

Sometelephonesystemsrequireyoutodialanaccesscode

(usually9)andwaitforaseconddialtonebeforedialingan

outsidenumber.Whenyoumanuallydialanumber,youcan

haveyourtelephonepauseanywhereduringthedialing

sequence.SimplypressPAUSEatthedesiredlocation.

Whenyouredialanumber,thetelephonepausesforaboutfour

secondsatthepauseentry.Forlongerpauses,pressPAUSE

again.

Caller ID Operation

IfyousubscribetoaCallerIDservice,thephoneautomatically

displaysinformationaboutcallsyoureceiveandstoresthe

informationinCallerIDmemory.Thesystemcanstoreupto99

incomingphonenumbersor64incomingphonenumberswith

namesintocallrecords.

Duringanincomingcall,thephonecompanyautomatically

sendsthecorrecttimebetweentherstandsecondringsto

updateyoursystem’sdisplay.

Review Call Records

PressUPorDOWN toreviewthenewcalls.Afterallnewcalls

havebeenreviewed,END OF NEW CALL appears.

Toreviewalltherecordsfromoldesttonewest,pressUP.To

reviewtherecordsfromnewesttooldest,pressDOWN.After

reviewingallrecordsinmemory,END OF LIST appears.

• Ifanincorrect,invalid,orincompleteCallerIDsignalis

received,LINE ERROR appearsonthedisplay.

• Ifthenameandnumberarenotavailableduetothe

caller’srestriction,PRIVATE CALLappearsonthedisplay.

• Ifthenameandnumberarenotavailable,

--UNAVAILABLE--appearsonthedisplay.

• RPTappearswithanumberifyouhavereceivedacall

fromthesamephonenumbermorethanonce.

• Ifyoudonotpressabuttonwithinabout15seconds,the

systemautomaticallyreturnstothenormaldisplay.

nNotes:

• TheNEW indicator remains ﬂashing until you have reviewed all

new calls.

• Thenumberofnewcallsdoesnotchangeuntilallcallshavebeen

reviewed and END OF NEW CALL appears. The new call counter

then resets to 0.

Call Back from Caller ID Memory

1. PressUPorDOWNtondthenumbertocallback.

2. PressCALL BACKtwice.LIFT HANDSET orPICK UP CALL

appears.

Andere Handbücher für 43-3905

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Radio Shack Telefon Handbücher

Radio Shack

Radio Shack 43-3911 Bedienungsanleitung

Radio Shack

Radio Shack ET-177 Bedienungsanleitung

Radio Shack

Radio Shack 17-919 Bedienungsanleitung

Radio Shack

Radio Shack ET-2105 Bedienungsanleitung

Radio Shack

Radio Shack 43-3901 Bedienungsanleitung

Radio Shack

Radio Shack ET-296 Bedienungsanleitung

Radio Shack

Radio Shack ET-182 Bedienungsanleitung

Radio Shack

Radio Shack ET-894 Bedienungsanleitung

Radio Shack

Radio Shack ET-893 Bedienungsanleitung

Radio Shack

Radio Shack CLEAR TRIM-FONE 43-858 Bedienungsanleitung

Radio Shack

Radio Shack ET-208 Bedienungsanleitung

Radio Shack

Radio Shack ET-469 Bedienungsanleitung

Radio Shack

Radio Shack System 1250 Bedienungsanleitung

Radio Shack

Radio Shack 43-3816 Bedienungsanleitung

Radio Shack

Radio Shack ET-928 Bedienungsanleitung

Radio Shack

Radio Shack ITZA 2 Bedienungsanleitung

Radio Shack

Radio Shack 43-883 Bedienungsanleitung

Radio Shack

Radio Shack 43-3818 Bedienungsanleitung

Radio Shack

Radio Shack ET-182 Bedienungsanleitung

Radio Shack

Radio Shack 17-918 Bedienungsanleitung

Radio Shack

Radio Shack ET-205 Bedienungsanleitung

Radio Shack

Radio Shack ET-212 Bedienungsanleitung

Radio Shack

Radio Shack 43-3241 Bedienungsanleitung

Radio Shack

Radio Shack 43-871 Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung

Ericsson

Ericsson Dialog 3213 Bedienungsanleitung

Yealink

Yealink VP530 Bedienungsanleitung