Radio Shack TAD-724 Bedienungsanleitung

Cat. No. 43-724

OWNER’S MANUAL

Please read before using this equipment.

TAD-724

Digital Answering System Telephone

with 13-Number Memory

43-724A.fm Page 1 Tuesday, May 16, 2000 4:51 PM

FEATURES

Your TAD-724 Digital Answering Sys-

tem Telephone is a sophisticated, fully

digital message center that combines

a telephone and an answering ma-

chine in one convenient package.

Fully digital means the TAD-724

stores all messages on a computer

chip. This gives you advanced capa-

bilities over tape-based answering

machines. For example, you can de-

lete an individual message while sav-

ing the rest.

And, because your TAD-724 is fully

digital, there are no tape mechanisms

to wear out and no tapes to bother

with.

The TAD-724 has these features:

ANSWERING SYSTEM

High Capacity — lets you record up

to 14 minutes of incoming/outgoing

messages and memos.

Voice Day/Time Stamp — records

the day and time each incoming mes-

sage was recorded.

Remote Operation — lets you use a

touch-tone phone (or rotary phone

and pocket tone dialer) to operate the

telephone answering device (TAD)

while you are away from your home or

office.

Remote Answer-On — lets you call

the TAD from a remote location and

set it to answer calls.

Memo Recording — lets you leave

messages for yourself or others in

your home or office.

Announce-Only — lets you set the

TAD to play an announcement or

memo for the caller, then automatical-

ly hang up without letting the caller

leave a message.

Phone Pick-Up Detection — stops

recording when you pick up any

phone on the same line as the TAD,

and resets to answer the next call.

Digitally-Synthesized Voice —

guides you through the operation of

many of the TAD’s features.

Built-In Announcement — lets you

immediately begin using the TAD to

answer calls and record messages.

Call Screening — lets you listen as a

caller leaves a message so you can

decide whether or not to answer a call.

Volume Control — lets you adjust the

speaker’s volume during message

playback.

RadioShack is a registered trademark used by Tandy Corporation.

43-724A.fm Page 2 Tuesday, May 16, 2000 4:51 PM

Programmable Remote Operation

Security Code — lets you set your

own 3-digit security code for remote

operation.

Room Monitor —lets you listen from

a remote location to the room where

the TAD is installed.

Adjustable Ring Number — lets you

set the TAD to answer after two, four,

or seven rings.

Toll-Saver — lets you avoid unneces-

sary toll charges when you call long-

distance to check your messages.

Multiple Outgoing Message Capaci-

ty — lets you set the TAD to play two

outgoing messages and record the

callers message.

Selectable Incoming Message

Length — lets you set the maximum

length of a caller’s message to 1 or 5

minutes.

Memory Full Warning — beeps twice

and announces “Memory is full.”

Memory Backup — protects stored

messages in case of a power failure.

Message Indicator — flashes to let

you know you have new messages.

Message Counter Indicator —

shows the number of messages the

TAD has recorded.

We recommend you record your sys-

tem’s serial number here. The number

is on the bottom of the TAD-724.

Serial Number __________________

Your system is ETL listed to UL stan-

dards and meets all applicable FCC

standards.

WARNING:To reduce the risk of fire or

shock hazard, do not expose this product to

rain or moisture.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVIC-

ING TO QUALIFIED PERSONNEL.

This symbol is intended to alert

you to the presence of uninsu-

lated dangerous voltage within

the product’s enclosure that

might be of sufficient magnitude

to constitute a risk of electric

shock. Do not open the product’s

case.

This symbol is intended to inform

you that important operating and

maintenance instructions are

included in the literature accom-

panying this product.

43-724A.fm Page 3 Tuesday, May 16, 2000 4:51 PM

TELEPHONE

13-Number Memory Dialing — lets

you store up to 13 phone numbers in

memory for easy dialing: 3 emergency

or priority (one-touch) numbers and 10

standard numbers.

Volume Control — lets you adjust the

handset’s volume.

Ringer Control — lets you turn the

ringer on or off.

Redial — lets you quickly dial the last

dialed number with the press of a but-

ton.

Flash — sends an electronic switch-

hook signal for use with special servic-

es, such as Call Waiting.

Mute — lets you talk to someone else

in the room without being overheard

by the person(s) on the phone.

Touch-Tone or Pulse Dialing — lets

you use the phone with either type of

service.

43-724A.fm Page 4 Tuesday, May 16, 2000 4:51 PM

READ THIS BEFORE

INSTALLATION

Your system conforms to federal regu-

lations, and you can connect it to most

telephone lines. However, each de-

vice that you connect to the phone line

draws power from the line. We refer to

this power draw as the device’s r

inger

equivalence number

, or REN. The

REN is on the bottom of the system.

If you are using more than one phone

or other device on the line, add up all

the RENs. If the total is more than five

(three in rural areas), your phone

might not ring or your system might

not answer. If ringer operation is im-

paired, remove a device from the line.

FCC STATEMENT

Your system complies with Part 68 of

FCC Rules

. You must, upon request,

provide the FCC registration number

and the REN to your phone company.

Both numbers are on the bottom of

your TAD.

Note: You must not connect your sys-

tem to:

• coin-operated systems

• party-line systems

• most electronic key phone sys-

tems

Your system complies with the limits

for a Class B digital device as speci-

fied in Part 15 of

FCC Rules

. These

limits provide reasonable protection

against radio and TV interference in a

residential area. However, your TAD

might cause TV or radio interference

even when it is operating properly. To

eliminate interference, you can try one

or more of the following corrective

measures:

• Reorient or relocate the receiving

antenna of the radio or TV

antenna.

• Increase the distance between the

TAD and the radio or TV.

• Use outlets on different electrical

circuits for the TAD and the radio

or TV.

Consult your local RadioShack store if

the problem still exists.

43-724A.fm Page 5 Tuesday, May 16, 2000 4:51 PM

CONTENTS

Installation ............................................................................................................ 7

Selecting a Location ........................................................................................ 7

Connecting Power ........................................................................................... 7

Installing Backup Batteries .............................................................................. 8

Mounting the TAD-724 ..................................................................................... 9

Connecting the Handset ................................................................................ 10

Telephone Operation ......................................................................................... 11

Setting the Tone-Pulse Switch ....................................................................... 11

Setting the Ringer .......................................................................................... 11

Using Redial .................................................................................................. 11

Using Flash .................................................................................................... 11

Using Mute .................................................................................................... 12

Volume Control .............................................................................................. 12

Using Tone Services on a Pulse Line ............................................................ 12

Using Pause .................................................................................................. 12

Using Memory Dialing ................................................................................... 13

Answering System Preparation ........................................................................ 15

Turning the TAD On/Off ................................................................................. 15

Setting the Day and Time .............................................................................. 15

Setting the Number of Rings ......................................................................... 16

Toll Saver ....................................................................................................... 16

Recording Outgoing Messages (OGM) ......................................................... 16

Checking an OGM ......................................................................................... 17

Answering System Operation ........................................................................... 18

Setting the TAD to Answer Calls ................................................................... 18

Using the Announce-Only Feature ................................................................ 19

Screening Calls ............................................................................................. 19

Recording a Memo ........................................................................................ 19

Playing Incoming Messages .......................................................................... 20

Deleting Messages ........................................................................................ 20

Remote Operation .............................................................................................. 22

Changing the Remote Operation Security Code ........................................... 22

Operating the TAD from a Remote Location ................................................. 22

Remote Commands ....................................................................................... 23

Troubleshooting ................................................................................................. 25

Care and Maintenance ....................................................................................... 26

43-724A.fm Page 6 Tuesday, May 16, 2000 4:51 PM

INSTALLATION

SELECTING A

LOCATION

Select a location for the TAD-724 that

is near both a modular phone jack and

an AC outlet, and out of the way of

normal activities. You can place the

TAD on a flat surface or mount it on a

wall plate or directly on the wall.

Notes:

• If the phone line jack is not a mod-

ular jack, you must update the wir-

ing. You can convert the wiring

yourself, using jacks and adapters

available at any RadioShack

store. Or, you can let the phone

company update it for you.

• The USOC number of the jack to

be installed is RJ11C for a base-

board jack or RJ11W for a wall-

plate jack.

CONNECTING POWER

Caution: You must

use a Class 2 power

source that supplies

9 volts DC and delivers at

least 300 mA. Its center tip

must be set to positive and its

plug must fit the TAD-724's 9V

DC jack. The supplied adapter

meets these specifications.

Using an adapter that does

not meet these specifications

could damage the TAD-724 or

the adapter.

1. Insert the barrel plug of the sup-

plied AC adapter into the 9V DC

300mA

jack.

2. Route the adapter’s cord into the

strain-relief slot on the bottom of

the TAD.

3. Plug the other end of the AC

adapter into a standard AC outlet.

The TAD initializes itself and the LOW

BATTERY indicator lights. Then, after

running a self test, the TAD sets all in-

ternal default values and generates a

beep.

Notes:

• Do not press any of the TAD’s but-

tons while you are plugging the

adapter into the AC outlet. If you

accidentally press a button,

unplug the adapter from the AC

outlet, then plug it back in.

43-724A.fm Page 7 Tuesday, May 16, 2000 4:51 PM

• The answering system on your

TAD cannot operate without AC

power. However, you can make

and answer calls on the telephone

without AC power.

INSTALLING BACKUP

BATTERIES

If AC power fails or you unplug the

TAD, four AAA backup batteries (not

supplied) save messages and settings

for the day, time, and security code.

We recommend you use Radio Shack

alkaline batteries.

1. Use a Phillips screwdriver to

remove the screw on the battery

compartment cover, then open the

cover.

Note: The battery compartment

cover is hinged and cannot be

removed from the TAD.

2. Place the batteries in the compart-

ment according to the polarity

symbols (+ and –) marked inside.

3. Replace the cover and secure it

with the screw.

Replace the batteries if the LOW BAT-

TERY indicator turns on while the AC

adapter is properly connected.

Cautions:

• To avoid losing stored information,

be sure the AC adapter is plugged

in and connected to the TAD

before you replace the batteries.

• Always use new batteries of the

required size and type.

• Always remove old or weak bat-

teries. Batteries can leak chemi-

cals that can destroy electronic

parts.

• Dispose of old batteries promptly

and properly. Do not bury or burn

them.

43-724A.fm Page 8 Tuesday, May 16, 2000 4:51 PM

MOUNTING THE TAD-724

On a Desktop

1. Plug one end of the supplied mod-

ular cord into the TEL. LINE jack

on the back of the TAD.

2. Plug the other end of the supplied

phone cord into a phone jack.

On the Wall

To mount the TAD on a wall plate or

directly on a wall, follow these steps.

Notes:

• To mount the TAD directly on a

wall, you need a drill and two

screws (not supplied) with heads

that fit into the keyhole slots on

the mounting bracket.

• For direct wall mount-

ing you need to drill

two holes 315/16 inches

(100 mm) apart. Then,

thread the screws into

each hole, letting the

heads extend about 1/4

inch (6.3 mm) from the

wall.

1. Plug one end of the supplied mod-

ular cord into the TEL. LINE jack

on the back of the TAD (see illus-

tration in “On a Desktop”).

2. Locate the upper two slots on the

bottom of the TAD and insert the

wall bracket’s matching tabs into

the slots.

3. Carefully press down on the bot-

tom of the bracket until both tabs

on each side of the bracket snap

into place.

4. Route the phone cord into the

right groove on the wall mounting

bracket and route the AC

adapter’s cord into the left groove.

1/4

315/16

43-724A.fm Page 9 Tuesday, May 16, 2000 4:51 PM

5. Plug the other end of the supplied

phone cord into a phone jack. Line

up the keyhole slots on the

bracket with the studs on the wall

plate, then slide the TAD down

onto the wall plate until it is

secure.

6. Slide the handset holder up and

out of its retaining slot and rotate it

180°, then slide the holder back

into its slot.

CONNECTING THE

HANDSET

To connect the handset to the base of

the TAD, plug one end of the supplied

coiled cord into the phone jack on the

handset and plug the other end into

the phone jack on the left side of the

TAD. Place the handset in the cradle.

Note: Your local RadioShack store

sells a variety of longer coiled handset

cords, which are useful when you

mount the TAD on a wall.

43-724A.fm Page 10 Tuesday, May 16, 2000 4:51 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Radio Shack Telefon Handbücher

Radio Shack

Radio Shack ET-212 Bedienungsanleitung

Radio Shack

Radio Shack 43-3206 Bedienungsanleitung

Radio Shack

Radio Shack ET-928 Bedienungsanleitung

Radio Shack

Radio Shack 43-3201 Bedienungsanleitung

Radio Shack

Radio Shack ET-273 Bedienungsanleitung

Radio Shack

Radio Shack 43-3872 Bedienungsanleitung

Radio Shack

Radio Shack ET-886 Bedienungsanleitung

Radio Shack

Radio Shack Contempra II Bedienungsanleitung

Radio Shack

Radio Shack 43-3905 Bedienungsanleitung

Radio Shack

Radio Shack 17-918 Bedienungsanleitung

Radio Shack

Radio Shack 43-208 Bedienungsanleitung

Radio Shack

Radio Shack TAD-734 Bedienungsanleitung

Radio Shack

Radio Shack ET-294 Bedienungsanleitung

Radio Shack

Radio Shack Caller Bedienungsanleitung

Radio Shack

Radio Shack 02A01 Bedienungsanleitung

Radio Shack

Radio Shack 43-3905 Bedienungsanleitung

Radio Shack

Radio Shack ET-469 Bedienungsanleitung

Radio Shack

Radio Shack ET-3222 Bedienungsanleitung

Radio Shack

Radio Shack 43-838 Bedienungsanleitung

Radio Shack

Radio Shack 13-Memory Big-Button Telephone Bedienungsanleitung

Radio Shack

Radio Shack 43-3703 Bedienungsanleitung

Radio Shack

Radio Shack ET-182 Bedienungsanleitung

Radio Shack

Radio Shack HandsfreePhone withCallerID/CallWaiting Bedienungsanleitung

Radio Shack

Radio Shack ET-898 Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung

Ericsson

Ericsson Dialog 3213 Bedienungsanleitung

Yealink

Yealink VP530 Bedienungsanleitung