RADWAG PUE 5 Bedienungsanleitung

Quick Start

•PUE 5

Indicator

ITKB-14-01-12-20-EN

To view the full user manual, go to the website or scan the QR code:

radwag.com/en/manuals/W4C

1. CONTENT

Indicator

×1

Indicator

×1

2. NOTES AND WARNINGS

Operate the indicator in a room free from dust where the temperature ranges

0–40 °C (32–104 °F) and where the relative humidity is below 80%. Potential

temperature change shall occur gradually and slowly.

Place the scale on a table or a wall bracket ensuring stability. For the most stable

and repeatable results it is recommended to use an anti-vibration table.

+0 oC

+32oF

+104oF

+40 oC

Place the scale away from heat

sources. Avoid exposing the scale to

the sunlight.

Avoid exposing the scale to the inﬂu-

ence of a magnetic ﬁeld. Do not weigh

magnetic substances.

Not intended for use within EX zones.

Not intended for weighing explosive or

ﬂammable substances.

PUE 5.15

PUE 5.19

The indicator is ready for operation.

Press ON / OFF key to start the indicator.

3.2. Indicator Start-Up

3. PREPARING FOR WORK

3.1. Indicator Temperature Stabilization

Place the indicator on the workstation and leave it until it

reaches ambient temperature.

Prior to switching the device on let it

reach room temperature (estimated

stabilization time: 8 hours).

Connect the indicator to

the mains.

1 2

1- 8 h

Application

settings

192.192.0.00

TERMINAL

E2R

10:10

01.01.2020

POL

Mass Display

Proxy

Manager

MwManager

MWMH -

manager

MwManager State: Connected to MW-04

Connection method settings

RS 232 port settings

Connection method:

Device selection

MW01 MW-04

Application

settings

Parameters

User parameters

Communication

I/O functions

LH 1

3 4

RS 232

Port

Exit Disconnect

Com 57600 None 8 1

Baud rate Parity Data bits Stop bits

The PUE5 indicator operates in Windows environment. RADWAG applications are installed individually on customer’s

order. One of the basic applications is MwManager.

MwManager home screen.

4. HOME SCREEN

Application

settings

Parameters

Weighing result window Tare/Zero

Weighing platform

selection

Device

selection

Connection

method settings

Connection

settings

4.1. Home Screen

5. CONNECTING PERIPHERALS

ON OFF

InputsInputs

USB RS 232 USB Load CellLoad Cell

Load CellLoad Cell

Inputs

100-240VAC

50/60Hz 0,2A

RS 232

RS 485 USB Ethernet USB

1ON/OFF switch

2Power cord cable gland

34IN connector (option)

4RS232, RS485 or 2XPROFIBUS (IN, OUT) connector

5USB M12 4 pin connector

6RJ45 Ethernet connector

7USB panel connector

8USB panel connector

9RS485 cable gland (option)

10 4OUT connector (option)

11 RS232 connector

12 USB M12 4 pin connector

13 Load cell cable glands (4pcs)

6 7

6. CLEANING AND MAINTENANCE

6.2. Cleaning Tips

6.1. Notes and Warnings

Avoid using aggressive cleaning

agents (e.g. solvents, cleansers

containing chlorine, corrosive

substances or bleach).

• Glasselementscanbecleanedwithglasscleaner.

•STAINLESSSTEELELEMENTS,ALUMINUMcanbecleanedwithasoftclothslightlymoistenedwithasolutionofwater

and a mild detergent (e.g. soap or dishwashing liquid).

•Plasticelementscanbecleanedwithasoftclothslightlymoistenedwithasolutionofwaterandamilddetergent

(e.g. soap or dishwashing liquid).

•Drycleanedelementsusingsoftanddryclothorusedust-freepapertoweltoabsorbtheremainingmoisture.

•Donotinstallthecomponentsuntiltheyarecompletelydry.

Avoid using cleansers containing

abrasive substances or scouring

preparations.

Avoid using intense water jet for

cleaning.

Prior to cleaning it is necessary

to disconnect the indicator from

the mains. Unplug the connector

from the electrical socket. Unused

communication interfaces must be

covered with hole plugs.

For cleaning use only soft cloths made

of microﬁber. Do not use any abrasive

cloths or any material that may scratch

the surface!

Apply the cleanser onto the cloth ﬁrst.

www.radwag.com

Inhaltsverzeichnis

Andere RADWAG Messgerät Handbücher

RADWAG

RADWAG PUE C/31H Bedienungsanleitung

RADWAG

RADWAG SM-UYA 4Y Bedienungsanleitung

RADWAG

RADWAG MA X7.A Benutzerhandbuch

RADWAG

RADWAG MA 5Y Benutzerhandbuch

RADWAG

RADWAG PUE C315 Bedienungsanleitung

RADWAG

RADWAG PMV Benutzerhandbuch

RADWAG

RADWAG MA X2.IC.A Series Bedienungsanleitung

RADWAG

RADWAG PUE CY10 Bedienungsanleitung

RADWAG

RADWAG PMR SERIES Bedienungsanleitung

RADWAG

RADWAG PUE HY10 Bedienungsanleitung

RADWAG

RADWAG PMV Series Benutzerhandbuch

RADWAG

RADWAG PUE C32 Bedienungsanleitung

RADWAG

RADWAG PUE H315 Bedienungsanleitung

RADWAG

RADWAG MA X2.A Series Benutzerhandbuch

RADWAG

RADWAG MA 3Y Bedienungsanleitung

RADWAG

RADWAG WPT EX Series Bedienungsanleitung

RADWAG

RADWAG MAX 60 Bedienungsanleitung

RADWAG

RADWAG MA 50/1.R Benutzerhandbuch

RADWAG

RADWAG PUE HX5.EX Bedienungsanleitung

RADWAG

RADWAG PUE C315 Benutzerhandbuch

RADWAG

RADWAG PUE HX7 Bedienungsanleitung

RADWAG

RADWAG MA X2 Synergy Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung