Rancilio Classe 8 S Bedienungsanleitung

● DE

Manuale per il tecnico

Manuel destiné au technicien

Handbuch für den Techniker

Technician’s Manual

Manual para el tecnico

Macchina per caffè

Machine à café

Kaffeemaschinen

Coffee machine

Máquina para café

classe 8

Manuale per il tecnico

Manuel destiné au technicien

Handbuch für den Techniker

Technician’s Manual

Manual para el tecnico

Manual para o técnico

Gli interventi e le procedure di programmazione indicati in questo manuale, sono di

esclusiva pertinenza del tecnico installatore.

Ce symbole indique les opérations et les procédures de programmation devant être faites

exclusivement par un technicien installateur.

Die Eingriffe und Programmierungen, die in diesem Handbuch beschrieben werden,

dürfen nur von ausgebildeten Technikern durchgeführt werden.

The interventions and the programming procedures described in this manual may only

be carried out by the technician/installer.

Las intervenciones y los procedimientos de programación indicados en este manual,

están exclusivamente destinadas al técnico instalador.

PT As intervenções e os procedimentos de programação indicadas neste manual são de

pertinência exclusiva do técnico instalador.

EN ENGLISH

CONTENTS

1. Making coffee ................................................ 31

1.1 Number of dispensers

1.2 Operating cycle

2. Dispensing steam with the ISTEAM

SYSTEM.......................................................... 31

2.1 Renewal the millk nozzle

3. Barman Programming .................................. 32

3.1.Clock

3.2 Set timer

3.3 Timer cut-out

3.4 Washing of the coffee groups

3.5 Reset

4. Technician programmation .......................... 34

4.1 Select display language

4.2 Visualize and reset the total calculations

4.3 Dose programmation

4.4 Check distribution time

4.5 International settings

4.6 Cleaning

4.7 Visualize date and pressure

4.8 Adjust boiler pressure

4.9 ISTEAM functions

4.10 Align probes

4.11 Software version and date

5. Visualizations ................................................ 38

5.1 Heating phase

5.2 Machine ready

5.3 Safety devices

5.4 Dose programming phase

5.5 List of failures

IT ITALIANO 3-11

FR FRANCAIS 12-20

DE DEUTSCH 21-29

EN ENGLISH 30-38

ES ESPAÑOL 39-47

PT PORTUGUêS 48-56

2.1 Renewal the millk nozzle

To increase the quantity of frothed milk,

change the standard emulsion nozzle

(indicated by a notch) removing the same

as indicated in the gure.

 Install the large nozzle (identied by

2 notches) to increase the quantity of

whipped milk.

Note: ISTEAM nozzles are different to

those utilised for the TSC

2. DISPENSING STEAM WITH THE

ISTEAM SYSTEM

To use this function, press the specic

buttons on the button panel; it is automa-

tically stopped when the set temperature

is reached.

Safety Devices

No steam can be dispensed if the machi-

ne has not reached the operating pressu-

re or temperature at least once.

Steam dispensing is discontinued auto-

matically after 3 minutes if the set tempe-

rature has not yet been reached.

1. MAKING COFFEE

1.1 Number of Dispensers

The coffee maker is equipped with 4 coffee dispen-

sers with programmable dose and pre-brewing cycle

time.

1.2 Operating Cycle

When one of the coffee buttons is pressed for one of

the 4 dispensers, the following occurs:

- The dispensing solenoid valves are energized

and the pump motor starts for a time that can be

programmed between 0 and 5 sec

- The dispensing solenoid valves are de-energized

and the pump motor stops for a time that can be

programmed between 0 and 5 sec

- The dispensing solenoid valves are energized

and the pump motor starts until the programmed

impulses are reached, which start decreasing

during the rst phase.

PICCOLO

SMALL

PETIT

KLEIN

PEQUEÑO

PEQUENO

GRANDE

GREAT

GRAND

GROSS

GRANDE

3. BARMAN PROGRAMMING

Use the rst coffee keyboard with keys having the

following functions :

1° Button Enter programming

Keeping pressed for 8 sec. you enter

programming, then you have:

1° Button “+” To move to a higher level in the

programming menus. Or to

increase the value

2°Button “-” To move to a lower level in the

programming menus. Or to

decrease the value

3° Button “enter” To enter the programming menu.

Or to conrm entries

4° Button “esc” To quit the menu

Or to quit programming mode.

5° Button Key off.

8 SEC

+enter esc

CLOCK SET DATE

SET HOUR

FORMAT DATE

HOUR

SET TIMER STAND BY

TIMER

SUN

8.7.1.Clock

Sub-menu to set date and time and mode (24 hours

or English 12 hours and date with dd/mm/yy or

mm/dd/yy)

8.7.2 Set timer

Menu to set automatic switching on/off of the machine

as follows:

- select automatic or manual switching on (to enable

function or not)

- set switching on time for every day of the week

- set working hours

To browse from one menu to another press “+” or “-”,

to enter a sub-menu or to conrm a variation press

“enter”, to exit press “esc”.

The value that can be modied with “+” or “-” keys

is ashing.

3.4 Reset

Keeping pressed key “ESC” (key 4 of push button

panel 1) and the machine is switched on, all data

set in the program are reset and default standard

data are automatically entered (coffee doses, water

doses, boiler pressure,etc.)

8.7.3 Timer-cut-out

If the machine is turned off by the program, by pres-

sing key 4 of keybord 1 at least for 3-4 seconds it will

turn on again and remain on until the following pro-

grammed stop or by pressing the same key again.

If the machine is switched on by the programme, by

pressing key 4 of the rst push-button panel for at

least 3-4 seconds it will switch off and remain off until

switch-on is programmed again or the same key is

pressed again.

3.1 Washing of the coffee groups

At the xed time, if the automatic washing (par.2.6)

mode is enabled, a message on the display requests

to wash the coffee groups.

Keep “ENTER” button pressed to start washing until

the display shows:

“Group Cleaning?”

“press <ENTER>”

If you press “enter” within 10 seconds, the following

cycle starts (if you do not leave this menu automa-

tically):

- The display shows:

”Insert blind

then <ENTER>”

- When you press “enter”, the cleaning cycle starts

and the display shows:

”Cleaning runnign”

The machine carries out n. 10 cycles as follows:

- Starts dispensing from the groups for 10 sec.

- Pauses for 10 sec.

At the end of the 10 cycles, the display reads:

”Remove lterh.

press <ENTER>”

If you press “enter” the display shows:

”Rinsing”

The machine carries out n. 2 cycles as follows:

- Starts dispensing from the groups for 30 sec.

- Pauses for 30 sec.

Keeping ‘’esc’’ pressed for 2 seconds, during the

cycle the current washing phase will stop and the

next phase will take place.

It is advisable to always complete the rinsing cycle

to remove any detergent residues.

N.B. In the washing and rinsing phases the groups

are operated alternatively.

In any case the washing of the coffee groups can

be enabled whenever necessary according to the

previously described procedure.

- Select display language

- Visualize and reset total calculations

- Dose programming

- Check distribution time

- International settings

- Enable washing

- Visualize date/pressure

- Adjust pressure

- ISTEAM function

- Align probes

- Software version and date

To browse from one menu to another press “+” or “-”,

to enter a sub-menu or to conrm a variation press

“enter”, to exit press “esc”.

The value that can be modied with “+” or “-” keys

is ashing.

4. TECHNICIAN PROGRAMMATION

To access programmation functions reserved to

technicians, proceed as follows:

- Turn off the machine

- Press key 5 and turn on the machine at the same

time

- Keep key 5 pressed until the display shows the

rst item of the programmation menu

4.1 Select display language

Menu to select the language to be used for display

visualizations.

Messages in the following languages shall be pro-

vided:

- Italian

- English

- French

- Spanish

- German

- Portuguese

4.2 Visualize and reset the total

calculations

The calculations for each selection made are visua-

lized and requested whether to set the counters to

zero or not.

4.3 Dose programmation

It visualizes the pulses and the pre-infusion time for

each coffee and hot water distribution time for each

button.

Doses are varied with “+” and “-” buttons.

4.5 International settings

Selection of the measures to be used for pressure

and temperature from ba to P.S.I. and from C to

°F°.

4.4 Check distribution time

Possibility of activating one of the following func-

tions:

- Function “0” – Function not enabled

- Function “1” –the distribution time for each coffee

will be displayed at the end of the distribution of a

t12 time.

- Function “2” –During the dose programming pha-

se, in self-learning or at the rst distribution after

varying a dose, the time of each distribution is

stored. This time is compared during the following

distributions and will be displayed for a t12 time at

the end of the distribution:

- “O.K.” if the distribution time falls within a tole-

rance of +/- 3 sec

- on the contrary if the difference in seconds is

higher than the tolerance, the non-corrected data

will be displayed (ex. “+5”)

4.6 Cleaning

This submenu gives the possibility of setting all

modes concerning the washing of coffee groups, and

washing counters.

If the automatic operation mode is set, at the xed

time, a message on the display will remind to start

the washing cycles.

4.7 Visualize date and pressure

Setting of the display visualization of date/time or

boiler pressure value.

4.11 Software version and date

The software update version is shown on the di-

splay.

4.8 Adjust boiler pressure

Adjustment of the boiler pressure values with value

increase of 0,05 bar.

4.9 ISTEAM functions

The temperature values and milk cream level are

set.

The following options are visualized:

For “whipped milk” the nal milk temperature can

be set (in °C / °F degrees) as well as the whipping

level ranging from 1 to 12.

Also for “non whipped milk” , in addition to the nal

temperature, a slight whipping can be set (ranging

from 1 to 12).

4.10 Align probes

Boiler temperature probe alignment

This function allows to carry out via software the ali-

gnment of the boiler temperature probes in relation

to a reference value.

The display shows the pressure measured by the

probe in real time and the corresponding alignment

value.

Make sure that the pressure read with a reference

manometer corresponds to the value read by the

probe.

Should the manometer show a higher or lower pres-

sure, correct with “+” or “-” buttons in order to carry

out the temperature control system alignment; press

“enter” to conrm.

Andere Handbücher für Classe 8 S

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rancilio Kaffeemaschine Handbücher

Rancilio

Rancilio Classe 10S Bedienungsanleitung

Rancilio

Rancilio Classe 6 E Bedienungsanleitung

Rancilio

Rancilio EPOCA E Bedienungsanleitung

Rancilio

Rancilio LEVA Bedienungsanleitung

Rancilio

Rancilio Classe 8 DE Bedienungsanleitung

Rancilio

Rancilio Baby 9 Bedienungsanleitung

Rancilio

Rancilio CLASSE 7 Bedienungsanleitung

Rancilio

Rancilio Classe 6 E Bedienungsanleitung

Rancilio

Rancilio Silvia Bedienungsanleitung

Rancilio

Rancilio Classe 9USB XCELSIUS TALL Bedienungsanleitung

Rancilio

Rancilio Classe 7S Bedienungsanleitung

Rancilio

Rancilio Classe 9S Bedienungsanleitung

Rancilio

Rancilio KRYO 65 OD Bedienungsanleitung

Rancilio

Rancilio EGRO 55 Series Bedienungsanleitung

Rancilio

Rancilio Silvia Bedienungsanleitung

Rancilio

Rancilio Silvia M Bedienungsanleitung

Rancilio

Rancilio EGRO ONE Touch Pure Coffee Bedienungsanleitung

Rancilio

Rancilio Classe 6 E Benutzerhandbuch

Rancilio

Rancilio CLASSE 11 Series Bedienungsanleitung

Rancilio

Rancilio CLASSE 7 Bedienungsanleitung

Rancilio

Rancilio Epoca S Bedienungsanleitung

Rancilio

Rancilio EGRO 5513 Bedienungsanleitung

Rancilio

Rancilio CLASSE 10 Benutzerhandbuch

Rancilio

Rancilio EGRO ONE Touch Pure Coffee Bedienungsanleitung

Beliebte Kaffeemaschine Handbücher anderer Marken

Taurus

Taurus Livorno 6 Bedienungsanleitung

Delta-q

Delta-q QUICK Bedienungsanleitung

Bunn

Bunn LCA-1 Fehlerbehebungshandbuch

Black & Decker

Black & Decker BLACK DECKER HOME DE790 Montageanleitung

Saeco

Saeco Vienna Plus Sup 018M Bedienungsanleitung

DeLonghi

DeLonghi DC300 Bedienungsanleitung

INCAPTO

INCAPTO BXCO1470E Bedienungsanleitung

Bosch

Bosch TASSIMO finesse TAS16B Series Bedienungsanleitung

Exido

Exido 245-072 Bedienungsanleitung

Animo

Animo OptiVend Choco Bedienungsanleitung

Siemens

Siemens TQ505DF Series Bedienungsanleitung

DeLonghi

DeLonghi ECI341 Bedienungsanleitung

Krups

Krups KT406511 Bedienungsanleitung

Cimbali

Cimbali M32 Classic Bedienungsanleitung

Philips

Philips HL3844N Bedienungsanleitung

Bosch

Bosch TES 515 SERIES Bedienungsanleitung

Tekmatix

Tekmatix TMFM - 65 Bedienungsanleitung

Scarlett

Scarlett SC-CM33005 Bedienungsanleitung