R&S QPS201 Bedienungsanleitung
R&S®QPS201
Quick Personnel Security Scanner
Getting Started
1179343802
Version 02
(;ÝRV2)
This manual contains information about the R&S®QPS201 and accesories with the following order num-
bers:
●R&S®QPS201 (HW 3.30) (order no. 1333.5000K02)
●R&S®QPS201 (HW 3.50) (order no. 1340.0030K02)
●R&S®LPS (order no. 1340.8001.02)
© 2021 Rohde & Schwarz GmbH & Co. KG
Mühldorfstr. 15, 81671 München, Germany
Phone: +49 89 41 29 - 0
Email: [email protected]
Internet: www.rohde-schwarz.com
Subject to change – data without tolerance limits is not binding.
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
Trade names are trademarks of the owners.
1179.3438.02 | Version 02 | R&S®QPS201
Throughout this manual, products from Rohde & Schwarz are indicated without the ® symbol and without the model designation, e.g.
R&S®QPS201 (HW 3.30) is indicated as R&S QPS.
Contents
R&S®QPS201
3Getting Started 1179.3438.02 ─ 02
Contents
1 Safety Instructions.................................................................................5
2 Regulatory Information..........................................................................8
3 Key Features.........................................................................................10
4 EMI Suppression.................................................................................. 11
5 System Components........................................................................... 12
6 Preparing for Use.................................................................................14
Contents
R&S®QPS201
4Getting Started 1179.3438.02 ─ 02
Safety Instructions
R&S®QPS201
5Getting Started 1179.3438.02 ─ 02
1 Safety Instructions
The R&S QPS is manufactured according to the highest technical standards. To use
the scanner safely, follow the instructions provided here and throughout the product
documentation. Keep the documentation nearby and offer it to other users.
Use the scanner only as intended and within its performance limits. The limits are
described in the product documentation, such as the data sheet, manuals and this bro-
chure. If you are unsure about the appropriate use, contact the Rohde & Schwarz cus-
tomer service.
Using the scanner requires specialists or specially trained personnel. These users also
need sound knowledge of at least one of the languages in which the user interface and
the product documentation are available.
If any part of the product is damaged or broken, stop using the product. Never open
the casing of the scanner or its components. Only service personnel authorized by
Rohde & Schwarz are allowed to repair the product.
Lifting, carrying and installing the R&S QPS
The R&S QPS is heavy and can cause physical injuries when it falls or tips over.
Setup and installation must be done by trained staff. Make sure to install the R&S QPS
exactly as described in the installation manual. During the installation, make sure that
the installation site is only accessible by people working on the installation.
Because of its weight, at least two strong people are required to move or install the
scanner. Lifting heavy items can cause structural and muscular injuries. You must use
the specially designed installation tool if you have to move or lift the scanner panels
(R&S QPS-Z800, order no. 1333.5900.02). You must also use the installation tool to
install the scanner on the platform.
Using the installation tool can pinch your fingers, especially when you attach it to the
R&S QPS and when you use the levers.
Loose ball-lock pins can cause the panels to fall over during transportation. Make sure
that the ball-lock pin is seated correctly whenever you use one.
If you have to move the pallet the R&S QPS is delivered on, always use a forklift.
During transport, installation or repair, wear appropriate protective clothing that com-
plies with your local rules and regulations. If you are unsure of which equipment to use,
ask your safety inspector.
We recommend to wear:
●Safety shoes with toe cap and ESD protection.
●Protective gloves
ESD protected shoes and gloves also protect the hardware from being damaged.
Safety Instructions
R&S®QPS201
6Getting Started 1179.3438.02 ─ 02
Installing cables
A R&S QPS installation consisting of the scanner, operator touchscreen and monitors
requires cable connections (power cables, LAN cables etc.). Make sure to secure all
cables on the floor and cover them up.
Loose cables are a tripping hazard. Tripping on cables can cause physical injuries.
Properly covered cables also minimize the risk of cable damage.
Choosing the operating site
Use the R&S QPS only indoors. The R&S QPS is not waterproof and water that enters
can electrically connect the casing with live parts. This can lead to electric shock, seri-
ous personal injury or death if you touch the casing.
For more information on environmental operating conditions, such as ambient temper-
ature, and humidity, see the data sheet.
Supplying the R&S QPS with power
You can connect the R&S QPS to the power distribution system normally used to sup-
ply energy-consuming equipment, such as household appliances and similar loads.
Electrically powered products have risks, such as electric shock, fire, personal injury or
even death.
Take the following measures for your safety:
●Only use the power cable delivered with the R&S QPS. It complies with country-
specific safety requirements. Only insert the plug into an approved grounded outlet.
●For components that need an external AC adapter, only use the one that is deliv-
ered with the components.
●Only use intact cables and route them carefully so that they cannot be damaged.
Check the power cables regularly to ensure that they are undamaged.
●If the voltage or frequency is higher than 230 V or 50 Hz, the leakage current of the
R&S QPS can be above the limits. In that case, a protective ground connection
must be established for each panel before connecting them to the mains supply.
●Only connect the R&S QPS to supply networks with a fuse protection of maximum
20 A.
●Ensure that you can disconnect the product from the mains supply at any time. Pull
the power plug to disconnect the product. The power plug must be easily accessi-
ble.
Calibrating the R&S QPS
The calibration cylinder is heavy and can cause physical injury.
Install the calibration cylinder exactly as described in the installation manual.
At least two people are required to carry or lift the calibration cylinder.
Installing the calibration cylinder requires a ladder. At least two people are therefore
required to install the calibration cylinder - one person must secure the cylinder and
ladder while the second person assembles the calibration setup.
Safety Instructions
R&S®QPS201
7Getting Started 1179.3438.02 ─ 02
Meaning of safety labels
Safety labels on the product warn against potential risks.
Potential hazard
Indicates a potential risk like personal injury or product damage. Read the product documenta-
tion for more information.
Electric hazard
Indicates live parts. Risk of electric shock, fire, personal injury or even death.
Protective ground terminal
Connect this terminal to a grounded external conductor or to protective ground. This protects
you against electric shock if an electric problem occurs.
Pinched fingers
Indicates a potential risk of pinching your hands or fingers.
Protective clothing
Indicates that you must wear protective clothing when you use the device to avoid physical
injuries.
Read manual
Indicates that you must read the product manual before using the device. The manual contains
instructions on how to use the device correctly.
Regulatory Information
R&S®QPS201
8Getting Started 1179.3438.02 ─ 02
2 Regulatory Information
The R&S QPS complies with the following regulations.
2.1 Regulations for Canada
This device contains licence-exempt transmitter(s) / receiver(s) that comply with Inno-
vation, Science and Economic Development Canada's licence-exempt RSS(s). Opera-
tion is subject to the following three conditions:
●This device may not cause interference.
●This device must accept any interference, including interference that may cause
undesired operation of the device.
●This device shall be used indoors only.
Cet appareil contient un (des) émetteur(s) / récepteur(s) exempts de licence, con-
forme(s) aux normes CNR d’Innovation, Sciences et Développement économique Can-
ada (ISDE). L’opération est soumise aux trois conditions suivantes:
●Cet appareil ne doit pas provoquer d'interférences.
●Cet appareil doit accepter toute interférence, y compris les interférences suscepti-
bles de provoquer un fonctionnement indésirable de l'appareil.
●Cet appareil doit être utilisé à l'intérieur uniquement.
2.2 Regulations for the USA
Changes or modifications not expressly approved by the party responsible for compli-
ance could void the user's authority to operate the equipment.
The R&S QPS is currently restricted to indoor operations (as of October 2020).
The R&S QPS may only be operated on a non-interference basis to existing and future
services with frequency allocations in the 70 GHz to 80 GHz frequency band, and
operators will be required to mitigate any instances of harmful interference that may
occur.
This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-
ing two conditions:
●This device may not cause interference.
●This device must accept any interference, including interference that may cause
undesired operation of the device.
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference when the equipment is oper-
ated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
Regulations for the USA
Regulatory Information
R&S®QPS201
9Getting Started 1179.3438.02 ─ 02
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Regulations for the USA
Key Features
R&S®QPS201
10Getting Started 1179.3438.02 ─ 02
3 Key Features
The R&S QPS Quick Personnel Security Scanner is a system that allows the detection
of hidden metallic and non-metallic objects that a person might carry in or underneath
their clothing.
Possible threats like weapons or explosives can be detected and measures taken
against them.
The objects are recognized by an evaluation of the reflected (backscattered) micro-
wave signal. The microwaves are of very low intensity. The signal level is several
orders of magnitude below the signal level of mobile phones. Therefore, the system
presents no health hazards for the scanned persons.
A person is scanned, front and back. The data is analyzed and evaluated by an auto-
matic detection software (algorithm).
After the evaluation, the scanned person either is cleared, or has to undergo further
investigation in the form of a manual screening. The manual screening can be per-
formed by the screener or by additional inspectors in a separate resolution station.
In case of an inadequate scan, the scan can be repeated or followed by manual
screening.
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere R&S Scanner Handbücher
