Rane Zonetech Bedienungsanleitung

UserGuide

English(3–25)

Appendix

English(26–27)

UserGuide(English)

Introduction

Thank you for purchasing the Zonetech. At Rane, performance and reliability mean as much to

us as they do to you. That’s why we design our equipment with only one thing in mind—to

make your performance the best it canbe.

BoxContents

Zonetech

(1) 6-pin 3.8 mm Euroblock inputs (green, for audio inputs)

(3) 6-pin 3.8 mm Euroblock outputs (orange, for zone outputs)

(1) 3-pin 3.8 mm Euroblock outputs (orange, for zone outputs)

(1) 3-pin 3.8 mm Euroblock inputs (black, for logic input)

Bluetooth® Antenna

Power Cable

Quickstart Guide

Safety & Warranty Manual

Support

For the latest information about this product (documentation, technical specifications, system

requirements, compatibility information, etc.) and product registration, visit rane.com.

For additional product support, visit rane.com/support.

Device

Paging

Remote

(e.g.,Rane

RAD16z)

Stereo Audio Inputs

(Receiver, DVD

Player,etc.)

MASTER

SOURCE

ZONE2 ZONE 2 ZONE 3 ZONE 3 INFO OPTION QUICK SELECT

ON/OFF SOURCE ON/OFF SOURCE STATUS

DIMMER 1CBL/SAT 2Blu-ra

3GAME 4NETW ORK

Power

Setup

Items not listed under Introduction >Box Contents are sold separately.

Use the included Euroblock connectors or stereo RCA cables to connect the inputs on

the rear panel to your audiosources.

Use the included Euroblock connectors to connect the outputs on the rear panel to your

zone amplifiers or poweredloudspeakers.

Use shielded Cat5e or Cat6 RJ45 cables to connect optional remotes or paging devices

(e.g., Rane DR6, Rane DRZH, Rane RAD devices) to the Master Remote Port, Zone

Remotes Ports, and Pager Port on the rearpanel.

Attach the Bluetooth antenna (included) to the Bluetooth antenna connector on the rear

panel. For best results, place Zonetech and the Bluetooth antenna so that it is not

obstructed by walls, furniture,etc.

Use an Ethernet cable to connect the Computer Ethernet Port on the rear panel to a

computer, router, or similar accesspoint.

Power on all of your audio sources (media players, stereos, microphones, amplifiers, etc.).

Use a standard IEC cable (included) to connect the power input to a poweroutlet.

Power on all of your audiooutputs.

Example

Bluetooth

Mono Audio Inputs

(Amplifier and Microphones)

Router Master

Remote

(e.g.,Rane

DR6)

Zone

Remote

(e.g.,Rane

DRZH)

Zone Amplifiers / Powered Speakers

Features

FrontPanel

Display: This display shows information about Zonetech’s current status andoptions.

Power Light: This light is on when Zonetech is poweredon.

Computer Link Light: This light is on when the Computer Ethernet port on the rear

panel is connected to a computer (powered on). You can then use the computer to

control Zonetech remotely using a web-basedinterace.

Bluetooth Light: This light will flash when Zonetech is in Pairing Mode. It will be lit solidly

when Zonetech is paired with an active Bluetooth device. When paired, you can then

send the device’s audio signal to Zonetechwirelessly.

Info: Turn this knob to navigate lists and menus in the display. Press this knob to cycle

through the Infopages shown in thedisplay.

Left/Right (/): Press each of these buttons to select the previous or next option

(respectively) shown in thedisplay.

Bluetooth: Press and hold this button for 5 seconds to enter Pairing Mode in which

Zonetech will search for a nearby Bluetooth device. Doing this will disconnect Zonetech

from a currently paired Bluetooth device.

Page: Press this button to show the Pager settings in thedisplay.

Input 1–6: Press each of these buttons to select the corresponding input. Its information

will appear in the display. You can then use the Info knob and Left/Right (/) buttons

to edit itssettings.

10.

Zone 1–6: Press each of these buttons to select the corresponding input. Its information

will appear in the display. You can then use the Info knob andr Left/Right (/) buttons

to edit itssettings.

9 7

6 5 4

823

4 3 3 3 3

7 6

5 5 5

RearPanel

Power Input (IEC): Use a standard IEC cable to connect this input to a poweroutlet.

Bluetooth Antenna Connector (SMA): Connect the included Bluetooth antennahere.

Inputs (stereo RCA): Connect audio sources to these stereo inputpairs.

Inputs(Euroblock):Connectbalancedorunbalancedaudiosourcestothesemonoinputs.

Outputs (Euroblock): Connect line-level (-10 dBV to +4 dBu) devices to these balanced

outputs. The outputs for Zones 1–5 are mono; the Zone 6 output is stereo. Alternatively,

you can configure the Zone 6 output for mono use with a subwoofer (connected to the

R(LO) output) and main loudspeaker (connected to the L(HI)output).

Logic Input (Euroblock): Connect normally open external control contacts (relay or

equivalent) to these terminals. When the terminals are connected to each other (i.e., when

the switch is closed), all outputs will be muted. This would typically be used with a fire

alarm system to silence audio output during anemergency.

Zone Remotes Ports (RJ45, shielded Cat5e or Cat6 cables): Connect optional Rane

DRZH devices to these ports, which will allow you to select sources and adjust levels for

the zonesremotely.

Master Remote Port (RJ45, shielded Cat5e or Cat6 cables): Connect an optional Rane

DR6 remote control to this port, which will allow you to select sources and adjust levels

for all zonesremotely.

Pager Port (RJ45, shielded Cat5e or Cat6 cables): Connect an optional Rane RAD device

(e.g., RAD16z, RAD26, etc.) to provide analog audio and logic inputs. Available functions

will depend on the RAD model. Please see rane.com/zonetech for additional information.

10.

Computer Ethernet Port (Ethernet): Connect a computer to this port during setup. After

Zonetech is properly configured, you can connect a router or similar access point to this

port, allowing you to use a web browser on your computer to access an interface to

control Zonetech. Alternatively, connect this port directly to a computer using an Ethernet

crossover cable.

Important: For compliance, you must use the included antenna only. No substitutions or

modifications to the antenna are permitted.

Note: When this mute function is active, all front-panel controls will be locked. Mute will

appear in the display with a red background.

Note: If you do not need the pager function, you can connect an optional Rane DR6 to

this port instead. This will provide the same functions as a DR6 connected to the Master

Remote port (see #8above).

Operation

Editing InputSettings

You can use Zonetech’s display, Info knob, and Left/Right (/) buttons to edit the settings

of eachinput.

To select an input to edit, press the corresponding Input button (1–6) or the Bluetooth

button. The display will indicate which input is selected: Input 1–6 or Stream.

To show the previous or next setting for the selected input, use the Left/Right (/)

buttons (respectively). Turn the Info knob to adjust the value of each setting.

These are the editable input settings. The abbreviated name (shown when the setting is not

selected) is in parentheses.

Input Level (Level)

This is the volume level at the input stage:

-88.0 to +12.0 dB.

Low Shelf Level (LS Level)

This is the amount of “boost” (increase) or

“cut” (decrease) of the low-frequency

shelving filter: -15.0 to +8.0 dB.

Tip: If you are unsure of what this level

should be, it is better to use a lower setting

toallowforheadroomandtoprevent

clipping/distortion.

Low Shelf Frequency (LS Freq)

This is the center frequency of the low-

frequency shelving filter: 40–630 Hz

(default: 630 Hz).

PEQ Level

This is the amount of “boost” (increase) or

“cut” (decrease) of the mid-range parametric

equalization band: -15.0 to +8.0 dB.

Tip: Higher values allow you to boost bass

frequencies more but also require more

amplifier power.

PEQ Frequency (PEQ Freq)

This is the center frequency of the mid-

range parametric equalization band: 40 Hz

– 16 kHz (default: 630 Hz).

PEQ Bandwidth (PEQ Band)

This is the width of the mid-range

parametric equalization band: 0.300–4.000

oct (octaves) (default: 0.500 oct).

High Shelf Level (HS Level)

This is the amount of “boost” (increase) or

“cut” (decrease) of the high-frequency

shelving filter: -15.0 to +8.0 dB.

High Shelf Frequency (HS Freq)

This is the center frequency of the high-

frequency shelving filter: 630 Hz – 16 kHz

(default: 630 Hz).

Tip: Lower values allow you to boost treble

frequencies more but increases the risk of

overdriving the tweeters.

Input Type (???) (Inputs 5 and 6 only)

This is the type of device connected to Input

5 and Input 6: Dynamic (microphone),

Condenser (Microphone), Unbalanced

Line+, Balanced Line (default: Balanced

Line).

Stream Source (???)

This is the source from which Zonetech will

play streamed audio: None (off),

Bluetooth, AirPlay, UPnP/DLNA.

Note: Phantom power is enabled only

when Condenser or selected.

Tip: Unbalanced Line+ allows you to

connect two signals to input (most

commonly left and right RCA lines wired to

a single input).

Tip: Balanced Line is a typical fully

balanced line-level input as used with

commercial audio equipment.

EditingOutput(Zone)Settings

You can use Zonetech’s display, Info knob, and Left/Right (/) buttons to edit the settings

of each output(zone):

To select a zone to edit, press the corresponding Zone button (1–6). The display will

indicate which zone is selected: Zone 1–6.

To show the previous or next setting for the selected zone, use the Left/Right (/)

buttons (respectively). Turn the Info knob to adjust the value of each setting.

These are the editable zone settings. The abbreviated name (shown when the setting is not

selected) is in parentheses.

Output Level (Level)

This is the output volume level: -30.0 to

+12.0 dB (default: 0.0 dB). This is the

master volume of the zone.

Input Source (In Source)

This is the audio source of the zone: Input

1–6 or Stream.

Priority Source (Pr Source)

This is the audio source that will play

automatically when an incoming signal is

detected: Input 1–6 or Stream.

Priority Hold Time (H Time)

This determines how long it will take (in

seconds) for the output to switch back to

the original audio source after the priority

source signal falls below the threshold: 1–

60 Sec (default: 3 Sec).

Tip: Enabling this feature is ideal for

switching between audio sources (e.g., a

jukebox and a television) without requiring

user intervention. Tip: Avoid setting this value too low, which

can cause unintended switching between

signals.

Low Shelf Level (LS Level)

This is the amount of “boost” (increase) or

“cut” (decrease) of the low-frequency

shelving filter: -15.0 to +8.0 dB.

Low Shelf Frequency (LS Freq)

This is the center frequency of the low-

frequency shelving filter: 40–630 Hz

(default: 630 Hz).

Tip: Higher values allow you to boost bass

frequencies more but also require more

amplifier power.

Note: To control the zone settings remotely, you can also use a web-based interface

on your computer (connected to the Computer Ethernet port), one Rane DRZH remote

control per zone (connected to the Zone Remotes ports), or up to two Rane DR6 master

remote controls (connected to the Master Remote and Paging port). See Controlling

Zonetech Remotely for moreinformation.

PEQ Level

This is the amount of “boost” (increase) or

“cut” (decrease) of the mid-range parametric

equalization band: -15.0 to +8.0 dB.

PEQ Frequency (PEQ Freq)

This is the center frequency of the mid-

range parametric equalization band: 40 Hz

– 16 kHz (default: 630 Hz).

PEQ Bandwidth (PEQ Band)

This is the width of the mid-range

parametric equalization band: 0.300–4.000

oct (octaves) (default: 0.500 oct).

High Shelf Level (HS Level)

This is the amount of “boost” (increase) or

“cut” (decrease) of the high-frequency

shelving filter: -15.0 to +8.0 dB.

High Shelf Frequency (HS Freq)

This is the center frequency of the high-

frequency shelving filter: 630 Hz – 16 kHz

(default: 630 Hz).

Page Enable (PG Enable)

This feature determines whether or not the

zone will receive an audio signal from the

pager: Enabled (on), Disabled (off).

Tip: Lower values allow you to boost treble

frequencies more but increases the risk of

overdriving the tweeters.

Note: If this feature is on, remember to set

the Output Paging Level, which is

independent of the normal Zone Output

Level.

Page Level (PG Level)

This is the output volume level of the pager:

-30.0 to +12.0 dB (default: 0.0 dB).

Page Ducker Depth (PG Duck)

This determines how much the pager, when

activated, will attenuate the normal output

signal: 0.0 to -85.0 dB (default: -12.0 dB).

Tip: Setting this to -85.0 dB will completely

mute the normal output signal when the

pager is on.

Andere Handbücher für Zonetech

Inhaltsverzeichnis

Sprachen:

Andere Rane Musikmixer Handbücher

Rane

Rane TTM 57SL Bedienungsanleitung

Rane

Rane MLM82S Bedienungsanleitung

Rane

Rane MP 2016A Bedienungsanleitung

Rane

Rane TTM 52I Bedienungsanleitung

Rane

Rane SM 82S Bedienungsanleitung

Rane

Rane MP 24X Bedienungsanleitung

Rane

Rane MP 22 Bedienungsanleitung

Rane

Rane TTM57mkII Bedienungsanleitung

Rane

Rane SIXTY-ONE Bedienungsanleitung

Rane

Rane TTM 57SL Bedienungsanleitung

Rane

Rane FLM 82 Service-Handbuch

Rane

Rane SIXTY-ONE Bedienungsanleitung

Rane

Rane MP26 Bedienungsanleitung

Rane

Rane MP 24 Bedienungsanleitung

Rane

Rane MP 44 Bedienungsanleitung

Rane

Rane CM 86 Service-Handbuch

Rane

Rane MLM82S Bedienungsanleitung

Rane

Rane MP 22X Bedienungsanleitung

Rane

Rane Empath Bedienungsanleitung

Rane

Rane SM 82 Bedienungsanleitung

Rane

Rane MP25 Bedienungsanleitung

Rane

Rane SIXTY-TWO Bedienungsanleitung

Rane

Rane SIXTY-ONE Bedienungsanleitung

Rane

Rane CM 86 Kurzanleitung

Beliebte Musikmixer Handbücher anderer Marken

Neve

Neve 8816 Bedienungsanleitung

Mackie

Mackie Onyx Analogue Mixer Bedienungsanleitung

Behringer

Behringer EUROPOWER PMP518M Bedienungsanleitung

Peavey

Peavey S-32 Sanctuary Series Bedienungsanleitung

True

True T9 Touchscreen Console Bedienungsanleitung

Studiomaster

Studiomaster Air Pro 24 Bedienungsanleitung

Pioneer

Pioneer SVM 1000 - Audio/Video Mixer Bedienungsanleitung

Roland

Roland M-160 Bedienungsanleitung

Yamaha

Yamaha MR1642 Bedienungsanleitung

Ecler

Ecler MAC40v Bedienungsanleitung

Pioneer

Pioneer DJM 909 - Battle Mixer W/Effects Bedienungsanleitung

Veeder-Root

Veeder-Root TLS-350 Series Bedienungsanleitung

Alto

Alto APM80.QUAD Bedienungsanleitung

Omnitronic

Omnitronic PM-211 Bedienungsanleitung

SoundCraft

SoundCraft B400 Bedienungsanleitung

Roland

Roland SoundCanvas SC-8820 Bedienungsanleitung

CARVIN

CARVIN RX 1200 Bedienungsanleitung

Roland

Roland M-16E Bedienungsanleitung