Raptor 9764491 Bedienungsanleitung
raptor-products.com 1
Prod. No. 9764491
raptor-products.com
ROTATIONS LASER
RED CLASS 2
Rotationslaser rød
Rotasjonslaser rød
Rotationslaser röd
Pyörivä laser, punainen
GB
2ROTATIONS LASER RED CLASS 2
Supplied with:
• Rotations Laser 9764491
• Receiver FR 45 with clamp for levelling staff
• Rechargeable battery and charger
• Padded bag
• User manual
Characteristics:
• Working range up to a diameter of 400 meters
• Dust / water protection IP 54
• Permanent 90° plumb-beam
• Automatic TILT alarm function
• Auto-shut-off when out of level
• Manual mode
Technical data
Self-levelling: horizontal / vertical
Self-levelling range: ± 5°
Laser class: 2
Accuracy horizontal: ± 1,0 mm / 10 m
Accuracy vertical: ± 1,5 mm / 10 m
Working range w/FR 45 (diameter): 400 m
Permanent 90° plumb beam: yes
raptor-products.com 3
GB
TILT mode: yes
Manual mode: yes
Rotating speed: 600 rpm
Power supply / operating time: 20 h (NiMH)
Temperature range: -20°C - +50°C
Dust / water protection: IP 54
Power supply:
NiMH battery pack.
Mount the rechargeable battery box into the rotations laser.
Charging the battery
Connect the charger with the charging plug of the instrument and the power
source. If the charging LED is red the battery is being charged; if the LED is
green the battery is fully charged.
Attention
The rechargeable battery can be charged if it is
in the instrument or if it is outside.
Battery status indication:
If the ON/OFF LED on the unit ashes,
the battery has to be recharged.
GB
4ROTATIONS LASER RED CLASS 2
Features:
1. Laser emitting window
2. Rotating head
3. Handle
4. Battery compartment
5. Keypad
6. Support for vertical use
7. 5/8“ thread hole vertical
8. 5/8“ thread hole horizontal
9. Charging plug
1.
2.
3.
4.
5.
9.
6.
7.
8.
Operation:
Horizontal use
Set up the instrument on an even surface or mount it onto a tripod.
Vertical use
Set up the instrument vertically (on the side with the vertical 5/8“ hole)
or mount it onto a tripod with its vertical 5/8“ thread.
raptor-products.com 5
GB
Horizontal use
After powering on the unit a ashing laser diode indicates that the automatic
self-levelling procedure is working. The laser starts rotating when it is self-
levelled. If not the laser was set up outside of its self-levelling range. In this
case set up the instrument on a more even surface.
1.
2.
3.
6. 4.
5.
1. ON/OFF button
2. ON/OFF LED
3. MANUAL button
4. MANUAL LED
5. TILT LED
6. TILT button
POWER ON/OFF (1)
Power the laser on/off with button (1). If the red ON/OFF LED (2) is illuminated
the laser is powered on. First the laser dot is ashing, then the self-levelling
procedure starts automatically; meanwhile the TILT LED (5) is ashing. When
the self-levelling procedure is completed the laser rotates with 600 rpm and
the TILT LED (5) is illuminated permanently (= TILT function activated).
If in normal use the ON/OFF LED (1) ashes the battery has to be recharged.
TILT MODE (6)
After completion of the self-levelling procedure the TILT mode is automatically
enabled. If the level is now disturbed the rotation stops and the TILT LED is
ashing.
Press the TILT button (6) once: The rotation of the laser starts - but the TILT
mode is disabled. Press the TILT button (6) twice: The rotation of the laser
starts, the self-levelling procedure is completed and the laser restarts working
with enabled TILT mode.
Press button (6) to disable the TILT mode after completion of the self-levelling
procedure.
GB
6ROTATIONS LASER RED CLASS 2
MANUAL MODE (3)
Power on the laser with button (1). After completion of the self-levelling
procedure press button (3). The TILT LED (5) will power off and the MANUAL
LED (4) will be illuminated permanently. Now the laser can be used in slope
position, i. e. it can be used with a grade mount without giving TILT alarm.
In vertical position a required alignment can be made quick and safe by
means of the MAN function. When the alignment has been made quit the
MAN function.
APPLICATION
raptor-products.com 7
GB
Receiver FR 45:
9.
1.
5.
2. 4.
3.
11.
1.
10.
6.
7.
8.
FEATURES
1. Vial
2. Display
3. Reference indicator
4. Receiving window
5. ON / OFF switch
6. Loudspeaker
7. Battery compartment (back side)
8. Sound on / off
9. Accuracy coarse / normal / ne
10. Light on / off
11. Magnets
12. 1/4“-thread for clamp (back side)
SUPPLIED WITH
Receiver FR 45, battery, clamp, user manual
Technical Data
Indication Front display
Accuracy coarse ± 10 mm
Accuracy normal ± 4 mm
Accuracy ne ± 2 mm
Tones 3
Operating time 400h
Power supply 1 x 9V
SYMBOLS
1. Power ON / OFF
2. Battery status indicator
3. Detection indicator
4. Sound ON / OFF
5. Detected position indicator
GB
8ROTATIONS LASER RED CLASS 2
ACCURACY COARSE / NORMAL / FINE
The FR 45 is equipped with three precision modes. They can be chosen by
pressing button (9):
Accuracy coarse: ± 10 mm
Symbol on display: without symbol
Accuracy normal: ± 4 mm
Symbol on display:
Accuracy ne: ± 2 mm
Symbol on display:
INSTALLATION OF THE BATTERIES
• Open the battery compartment cover (7).
• Insert 1 x 9 V AA battery according to the installation symbol
(ensure correct polarity!). Close the cover.
• In order to save battery power the receiver will automatically turn off if it
has not received laser scanning singal for 5 minutes.
USE OF RECEIVER
Press the button (5) to switch the unit on.
Move the receiver up and down carefully to detect the laser beam.
A: Move the receiver down
Acoustic signal : ultra-short requent beep
B: Move the receiver up
Acoustic signal: short requent beep
C: On level
Acoustic signal: continuous beep
A+B: The closer the distance to „on level“ (C) is, the shorter the arrows
become.
raptor-products.com 9
GB
CLAMP FOR LEVELLING STAFF
If required the FR 45 can be attached to laser poles or any other equipment
by means of the clamp supplied with.
Safety notes:
SPECIFIC REASONS FOR ERRONEOUS MEASURING RESULTS
Measurements through glass or plastic windows; dirty laser emitting
windows; after the instrument has been dropped or hit. Please check the
accuracy. Large uctuation of temperature: If the instrument will be used in
cold areas after it has been stored in warm areas (or the other way round)
please wait some minutes before carrying out measurements.
CARE AND CLEANING
Handle measuring instruments with care. Clean with soft cloth only, after
any use. If necessary damp the cloth with some water. If the instrument is
wet clean and dry it carefully. Pack it up only if it is perfectly dry. Transport in
original container / case only.
ELECTROMAGNETIC ACCEPTABILITY (EMC)
It cannot be completely excluded that this instrument will disturb other
instruments (e.g. navigation systems); will be disturbed by other instruments
(e.g. intensive electromagnetic radiation nearby industrial facilities or radio
transmitters).
CE-CONFORMITY
The instrument has the CE mark according to EN 61010-1:2001 + corrig. 1+2.
WARRANTY
This product is warranted by the manufacturer to the original purchaser to be
free from defects in material and workmanship under normal use for a period
of two (2) years from the date of purchase. During the warranty period, and
upon proof of purchase, the product will be repaired or replaced (with the
same or similar model at manufacturers option), without charge for either
parts or labour. In case of a defect please contact the dealer where you
originally purchased this product. The warranty will not apply to this product
if it has been misused, abused or altered. Without limiting the foregoing,
leakage of the battery, bending or dropping the unit are presumed to be
defects resulting from misuse or abuse.
GB
10 ROTATIONS LASER RED CLASS 2
EXCEPTIONS FROM RESPONSIBILITY
1. The user of this product is expected to follow the instructions given in
the user manual. Although all instruments left our warehouse in perfect
condition and adjustment the user is expected to carry out periodic
checks of the product’s accuracy and general performance.
2. The manufacturer, or its representatives, assumes no responsibility of
results of a faulty or intentional usage or misuse including any direct,
indirect, consequential damage, and loss of prots.
3. The manufacturer, or its representatives, assumes no responsibility for
consequential damage, and loss of prots by any disaster (earthquake,
storm, ood etc.), re, accident, or an act of a third party and/or a usage
in other than usual conditions.
4. The manufacturer, or its representatives, assumes no responsibility for any
damage, and loss of prots due to a change of data, loss of data and
interruption of business etc., caused by using the product or an unusable
product.
5. The manufacturer, or its representatives, assumes no responsibility for any
damage, and loss of prots caused by usage other than explained in the
user manual.
6. The manufacturer, or its representatives, assumes no responsibility for
damage caused by wrong movement or action due to connecting with
other products.
INTENDED USE OF INSTRUMENT
The instrument emits a visible laser beam in order to carry out the following
measuring tasks (depending on the instrument): Setting up heights, horizontal
and vertical planes, right angles.
SAFETY INSTRUCTIONS
• Follow up the instructions given in the user manual.
• Do not stare into the beam. The laser beam can lead to eye injury. Looking
directly into the beam (even from greater distance) can cause damage to
your eyes.
• Do not aim the laser beam at persons or animals.
• The laser plane should be set up above the eye level of persons.
• Use the instrument for measuring jobs only.
• Do not open the instrument housing. Repairs should be carried out by
authorized workshops only. Please contact your local dealer.
Inhaltsverzeichnis
Sprachen:
Andere Raptor Laser-Nivelliergerät Handbücher
Beliebte Laser-Nivelliergerät Handbücher anderer Marken
Nedo
Nedo ET-5 Bedienungsanleitung
geo-FENNEL
geo-FENNEL Maxi-Liner FL 65 HP Bedienungsanleitung
LaserLiner
LaserLiner X2-Laser Bedienungsanleitung
Spectra
Spectra LL300N Bedienungsanleitung
geo-FENNEL
geo-FENNEL Selection PRO FLG 40-PowerCross GREEN SP Bedienungsanleitung
Nedo
Nedo Crossliner 4 Bedienungsanleitung
