Rauch AXIS EMC ISOBUS Bedienungsanleitung

AXIS EMC ISOBUS

Complementary instructions

Read carefully before

using the machine!

Keep for future reference.

This operator's manual/mounting manual

is to be considered as part of the

machine. Suppliers of new and second-

hand machines are required to document

in writing that the operator's manual/

mounting manual was delivered with the

machine and handed over to the

customer.. Version 4.11.00

5902180-h-en-0821

Original instructions

Dear customer,

By purchasing the AXIS EMC ISOBUS machine control unit for the AXIS EMC fertilizer spreader,

you have shown confidence in our product. Thank you very much! We want to justify this

confidence. You have purchased a powerful and reliable machine control unit.

However, in case unexpected problems arise, our customer service department is always there for

you.

Please read this operator's manual as well as the operator’s manual for the machine

carefully before using the machine, and follow the advice given.

This manual may also describe equipment that is not included in your machine control unit.

Note the serial number of the machine control unit and of the machine

The AXIS EMC ISOBUS machine control unit has been calibrated at the factory

for the mineral fertilizer spreader with which it was supplied. It cannot be

connected to another machine without recalibration.

Please enter the serial number of the machine control unit and of the machine

here. When connecting the machine control unit to the machine, these numbers

must be checked.

Serial number of electronic machine control unit:

Machine serial number:

Machine year of manufacture:

Technical improvements

We continuously strive to improve our products. For this reason, we reserve the right to make any

improvements and changes to our machine that we consider necessary without notice. We do not

accept any obligation to make such improvements or changes on machines that have already been

sold.

We will be pleased to answer any other questions that you might have.

Yours sincerely

RAUCH Landmaschinenfabrik GmbH

Table of contents

1 User instructions 7

1.1 About this operator’s manual 7

1.2 Meaning of warnings 7

1.3 Notes on text descriptions 8

1.3.1 Instructions and procedures 8

1.3.2 Lists 8

1.3.3 References 9

1.3.4 Menu hierarchy, keys and navigation 9

2 Layout and function 10

2.1 Overview of supported machines 10

2.2 Display 10

2.2.1 Description of the operating screen 11

2.2.2 Display fields 12

2.2.3 Display of the metering slide status 14

2.2.4 Display of sections 15

2.3 Library of icons used 16

2.3.1 Navigation 16

2.3.2 Menus 16

2.3.3 Operating screen icons 17

2.3.4 Other icons 20

2.4 Structural menu overview 21

3 Attachment and installation 23

3.1 Tractor requirements 23

3.2 Connections, sockets 23

3.2.1 Power supply 23

3.2.2 Connecting the machine control unit 23

3.2.3 Dosing slider preparation 27

4 Operation 28

4.1 Switching on the machine control unit 28

4.2 Navigation within the menus 29

4.3 Main menu 30

4.4 Fertilizer settings 31

Table of contents

AXIS EMC ISOBUS 5902180-h-gb- 3

4.4.1 Application rate 34

4.4.2 Set the working width 35

4.4.3 Flow factor 35

4.4.4 Drop point 37

4.4.5 Calibration 37

4.4.6 Disc type 40

4.4.7 RPM 41

4.4.8 Limited border spreading mode 42

4.4.9 Border spreading application rate 42

4.4.10 Calculate OptiPoint 43

4.4.11 GPS Control info 44

4.4.12 Fertilizer charts 45

4.5 Machine settings 49

4.5.1 AUTO/MAN mode 51

4.5.2 +/- quantity 52

4.6 Fast emptying 53

4.7 System/Test 55

4.7.1 Total data counter 56

4.7.2 Test/diagnosis 57

4.7.3 Service 60

4.8 Info 60

4.9 Weighing/Trip counter 60

4.9.1 Trip counter 61

4.9.2 Rest (ka, ha, m) 62

4.9.3 Zero scales 63

4.10 Operating lights (SpreadLight) 64

4.11 Hopper cover 65

4.12 Special functions 67

4.12.1 Changing the system of units 67

4.12.2 Using the joystick 68

4.12.3 WLAN module 71

5 Spreading operation 73

5.1 Requesting the remaining quantity during spreading 73

5.2 Refilling 73

5.3 TELIMAT border spreading unit 74

5.4 Electrical TELIMAT unit 75

5.5 Working with sections 76

5.5.1 Displaying the spreading type in the operating screen 76

5.5.2 Spreading with reduced sections: VariSpread V8 77

5.5.3 Spreading with reduced sections: VariSpread pro 79

5.5.4 Spreading operation with one section and in border spreading mode 82

5.6 Spreading with the automatic operating mode (AUTO km/h + AUTO kg) 83

5.7 Idle measurement 84

5.7.1 Automatic idle measurement 84

5.7.2 Manual idle measurement 86

5.8 Spreading with the AUTO km/h operating mode 86

Table of contents

45902180-h-gb- AXIS EMC ISOBUS

5.9 Spreading with the MAN km/h operating mode 87

5.10 Spreading in the MAN scale operating mode 88

5.11 GPS control 90

6 Alarm messages and possible causes 94

6.1 Meaning of the alarm messages 94

6.2 Fault/alarm 98

6.2.1 Acknowledging an alarm message 99

7 Special equipment 100

8 Guarantee and warranty 101

Table of contents

AXIS EMC ISOBUS 5902180-h-gb- 5

1 User instructions

1.1 About this operator’s manual

This operator's manual is an integral part of the machine control unit.

The operator’s manual contains important instructions for safe, proper, and economic use and

maintenance of the machine control unit. Compliance with its stipulations helps to avoid risks,

reduce repair costs and downtime, and to increase the reliability and service life of the machine

controlled with it.

The operator's manual must be kept in an easily accessible location close to where the control unit is

used (e.g., in the tractor).

The operator's manual does not replace your own responsibility as operator and operational staff of

the machine control unit.

1.2 Meaning of warnings

The warnings in the operator’s manual are classified according to the severeness of the risk and the

probability of its occurrence.

The warning symbols draw attention to the unavoidable residual risks inherent in the design to which

users of the machine are exposed. The warnings used are structured as follows:

Symbol + signal word

Explanation

Level of danger of warnings

The level of danger is indicated in the signal word. The levels of danger are classified as follows:

DANGER!

Type and source of danger

This warning warns of a danger posing an immediate threat to the health and life of people.

Ignoring these warnings will result in severe injury or death.

▶Always observe the measures described to prevent this danger.

WARNING!

Type and source of danger

This warning warns of a potentially dangerous situation for personal health.

Ignoring these warnings leads to severe injury.

▶Always observe the measures described to prevent this danger.

1. User instructions

AXIS EMC ISOBUS 5902180-h-gb- 7

CAUTION!

Type and source of danger

This warning warns of a potentially dangerous situation for personal health.

Ignoring these warnings leads to injury.

▶Always observe the measures described to prevent this danger.

NOTICE!

Type and source of danger

This warning warns of material and environmental damage.

Ignoring these warnings will result in damage to the machine and to the environment.

▶Always observe the measures described to prevent this danger.

Dies ist ein Hinweis:

Allgemeine Hinweise enthalten Anwendungstipps und besonders nützliche Informationen, jedoch

keine Warnungen vor Gefährdungen.

1.3 Notes on text descriptions

1.3.1 Instructions and procedures

Steps that the operator must carry out are shown as a numbered list.

uInstruction for action step 1

uInstruction for action step 2

Instructions involving only one step are not numbered. The same applies for actionsteps that do not

have a specific sequence.

A bullet is placed in front of these instructions:

• Handling instruction

1.3.2 Lists

Lists without a specific sequence are shown as lists with bullet points:

• Property A

• Property B

1. User instructions

85902180-h-gb- AXIS EMC ISOBUS

1.3.3 References

References to other sections in the document are shown with paragraph number, header text and/or

page number:

•Example: Please also note 2 Layout and function

References to other documents are shown as information or instructions without the exact chapter or

page number:

•Example: Follow the instructions in the operator’s manual of the universal drive shaft

manufacturer.

1.3.4 Menu hierarchy, keys and navigation

Menus are the entries listed in the main menu window.

The menus list submenus and/or menu items where settings can be made (selection lists, text or

number entries, starting a function).

The various menus and buttons of the machine control unit are illustrated in bold letters.

The hierarchy and the path to the requested menu item are marked with an > (arrow) between menu

and/or menu item(s):

• System / Test> System / Test > Test/diagnosis means that you can reach the menu item Voltage

via the menu item System / Test and the menu item Test/diagnosis.

○ The arrow > corresponds to the operation of the scroll wheel and/or the button at the screen

(touchscreen).

1. User instructions

AXIS EMC ISOBUS 5902180-h-gb- 9

2 Layout and function

Due to the great variety of different ISOBUS-compatible terminals, this chapter is limited to the

functions of the electronic machine control system without indicating a specific ISOBUS terminal.

• Please observe the instructions for the operation of your ISOBUS terminal in the

corresponding operator's manual.

2.1 Overview of supported machines

Some models are not available in all countries.

• AXIS H 30.2 EMC, AXIS H 30.2 EMC + W

• AXIS H 50.2 EMC + W

• AXIS M 20.2 EMC, AXIS M 20.2 EMC + W

• AXIS M 30.2 EMC, AXIS M 30.2 EMC + W

• AXIS-M 50.2 EMC + W

Supported functions

• Spreading depending on forward speed

• Electrical drop point setting

• RPM control

○ AXIS-M 20.2/30.2/50.2 EMC (+W): Drive shaft speed

○ AXIS-H 30.2/50.2 EMC (+W): Spreading disc speed

• EMC - mass flow control

• Continuous section control

2.2 Display

The display shows the current status information as well as the selection and input options for the

electronic machine control unit.

The most important information concerning the operation of the machine is displayed in the operating

screen.

2. Layout and function

10 5902180-h-gb- AXIS EMC ISOBUS

Inhaltsverzeichnis

Andere Rauch Landwirtschaftliche Geräte Handbücher

Rauch

Rauch UKS 150 Bedienungsanleitung

Rauch

Rauch Kuhn AXIS AXMAT Series Bedienungsanleitung

Rauch

Rauch RFZ 7 Bedienungsanleitung

Rauch

Rauch AERO GT 60.1 Bedienungsanleitung

Rauch

Rauch AXENT 90.1 Bedienungsanleitung

Rauch

Rauch AXIS-M 30.2 Bedienungsanleitung

Rauch

Rauch TELIMAT T 1 Bedienungsanleitung

Rauch

Rauch AXIS-H EMC Series Bedienungsanleitung

Rauch

Rauch KUHN AP 19 Bedienungsanleitung

Rauch

Rauch QUANTRON-I Bedienungsanleitung

Rauch

Rauch AXIS-M 20.2 EMC Bedienungsanleitung

Rauch

Rauch MDS 8.2 Bedienungsanleitung

Rauch

Rauch Kuhn RV 2M 1 Bedienungsanleitung

Rauch

Rauch TAXON 25.1 Bedienungsanleitung

Rauch

Rauch MDS.2 Q/W Bedienungsanleitung

Rauch

Rauch AERO 32.1 Bedienungsanleitung

Rauch

Rauch MDS Series Bedienungsanleitung

Rauch

Rauch Kuhn Axis AP-Drive Bedienungsanleitung

Rauch

Rauch AERO GT 60.1 Bedienungsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung