Raycus RFL-P20QB Bedienungsanleitung

编号

RFL-P20QB～P30QB

密级

阶段标记

页数

名称

RFL-P20QB～P30QB

脉冲光纤激光器英文使用说明书

会签

单位

第二事业部

编写

李科

校对

朱军

审核

施建宏

标审

李其军

批准

黄保

武汉锐科光纤激光技术股份有限公司

User’s guide Ytterbium Pulsed Fiber Laser RFL-P20QB～P30QB Ver.: 2.0

Ytterbium Pulsed Fiber Laser

User’s Guide

RFL-P20QB～P30QB

Wuhan Raycus Fiber Laser Technologies Co., Ltd.,2018

Issued 19 October 2018

User’s guide Ytterbium Pulsed Fiber Laser RFL-P20QB～P30QB Ver.: 2.0

Safety Information

Please read this instruction carefully and familiarize yourself with the information we have

provided before you use the product. In this brochure, important operation procedures, safety and

other information are provided for you and all future users. In order to ensure operatingsafely

and optimal performance of the product, please do according to following warnings, cautions and

other information.

Raycus pulsed fiber laser is classified as a high power Class IV laser device. Before supplying

the power to the device, please make sure that the correct voltage of 24VDC power source is

connected and the anode and cathode are right. Failure to connect power source correctly will

cause damage to the device.

The device emits invisible 1060~1085nm wavelength light with average power 20W/30W. Do

not expose your eyes or skin to the radiation of the laser.

Do not take apart the device, because there are no replaceable accessories available for users

to use. Any maintenance can only be proceeded in Raycus.

Do not look into the light output end directly. Use appropriate laser safety eyewear when

operating the device.

Safety labels and locations

The two labels above are located on the top of the cover of the device, representing laser

radicalization.

User’s guide Ytterbium Pulsed Fiber Laser RFL-P20QB～P30QB Ver.: 2.0

Content

1. Description......................................................................................................1

1.1. Product description........................................................................................................1

1.2. Actual configuration list ................................................................................................1

1.3. Environmental requirements and cautions.....................................................................1

1.4. Specifications.................................................................................................................2

2. Mounting.........................................................................................................3

2.1 Mounting dimensions ....................................................................................................3

2.2 Method of installation....................................................................................................3

3. Control Interface............................................................................................5

4. Operation Regulations...................................................................................8

4.1 Pre-inspection ................................................................................................................8

4.2 Operation procedures.....................................................................................................8

4.3 Cautions.........................................................................................................................8

5. Instructions for warranty, return and maintenance ..................................9

5.1 General warranty ...........................................................................................................9

5.2 Limitations of warranty .................................................................................................9

5.3 Service and repairs.........................................................................................................9

User’s guide Ytterbium Pulsed Fiber Laser RFL-P20QB～P30QB Ver.: 2.0

1.Description

1.1. Product description

Raycus P20QB/P30QB pulsed fiber laser is an ideal high power laser source with high speed

and high efficiency. It is specially designed for industrial laser making system and other

applications.

Compared with traditional lasers, pulsed laser has some unique advantages in increasing the

conversion efficiency of the pump light 10 times higher. Its low power consumption and

automotive design make it appropriate for operating both in and outside the lab. Besides, it is

exquisite and convenient for its independence in placement, free time in using and facility in

connecting to equipment directly.

The device can emit 1060~1085nm wavelength pulsed light under the control of industrial

laser’s standard interface driven by 24VDC power source.

1.2. Actual configuration list

Table 1. Configuration list

Items

Quantity

Remark

Fiber Lasermodule

1.3. Environmental requirements and cautions

Pulsed laser should be driven by 24VDC±1V power source.

(1) Caution: Make sure the corresponding wires of the device are properly grounded.

(2) All the maintenance to the device should only be done by Raycus, because there is no

replacement or accessory provided with the device. Please do not try to damage the labels or

open the cover in order to prevent against electric shock, or the warranty will be invalid.

(3) The output head of the product is connected with an optical cable. Please be careful handling

the output head. Avoid dirt and any other contaminations. Please use the specialized lens

paper when cleaning the lens. Please lid the laser with protective cover of the light isolator to

be against dirt only when the laser is not installed in the device or not in working.

(4) If the operating the device fails to follow this instruction, the protective function will be

User’s guide Ytterbium Pulsed Fiber Laser RFL-P20QB～P30QB Ver.: 2.0

weakened. Therefore, it should be used under normal conditions.

(5) Do not install the collimating device into the output head when the laser device is in working.

(6) The device has three cooling fans at the rear panel to dissipate heat. In order to guarantee

enough airflow to help giving heat off, there must be a space of at least 10cm’s width for

airflow in front and rear side of the device. As the cooling fans are working at blow condition,

if laser is mounted in a cabinet with fans, the direction should be same as laser’s fans.

(7) Do not look into the output head of the device directly. Please do wear appropriate laser

safety eyewear during the time when operating the device.

(8) Make sure the pulse repetition rate higher than 20 kHz.

(9) For the longest time without pulse is only 100 us. If there is no pulse output, please stop

marking at once, to avoid further damage of the device.

(10) Power source sudden interruption will do great harm to the laser device. Please make sure

the power supply works continuously.

1.4. Specifications

Table 2. P20QB/P30QB pulsed fiber laser specifications

Pulsed fiber laser

P20QB

P30QB

Wavelength(nm)

1060~1085

Polarization

Random

Optical isolator

Yes

Nominal average output power (W)

≥20

≥30

Single pulse energy (mJ)

1@20kHz

1@30kHz

Beam quality(M2)

<1.5

Beam Diameter(mm)

7±1

Pulse duration(ns)

<120@20kHz

<120@30kHz

Pulse repetition rate(kHz)

20 - 60

30 - 60

Output Power Tunability(%)

10-100

Output Fiber Cable length(m)

2.0

Working voltage(VDC)

24±1

Power consumption(W)

200@20℃300@20℃

Cooling

Forced Air Cooled

Dimension W×D×H(mm)

215×286×95

Operating temperature(℃) 0～40

Store temperature(℃) -20～60

Operating Humidity(%) ≤80%

User’s guide Ytterbium Pulsed Fiber Laser RFL-P20QB～P30QB Ver.: 2.0

2.Mounting

2.1 Mounting dimensions

(1) Fiber Laser module dimensions (As shown in Fig. 1).

Figure 1. Dimension drawing of laser module (Unit: mm).

(2) Isolated output isolator (As shown in Fig. 2).

Figure 2. Dimension drawing of output isolator (Unit: mm).

2.2 Method of installation

(1) The laser output fiber is the key but very sensitive component. During the package,

transport and operation, the bending radius of output fiber must not exceed 15 cm, or

the laser may be damaged. The leading and tail parts of the output fiber must not be

excessively bended, in case of damaging. When returning the laser for warranty, it

suggests using the original package. If the original package is not accessible, the laser

User’s guide Ytterbium Pulsed Fiber Laser RFL-P20QB～P30QB Ver.: 2.0

device and output isolator must be packed with suitable soft materials in case of

damaging due to vibration during the transportation.

(2) Fix the laser device steady on the holder and ensure good ventilation.

(3) The power connector of this high performance small volume laser device is DB7 dual

power supply. Connect the power line to the 24V DC power supply and ensure

sufficient output power. Notice the polarity of the power line.

Figure 3. Schematic of DB7 power supply connector.

Table 3. Definition of small volume laser power connector.

Definition

Color

Function

A1 P24V+ Red

24 V laser driver power supply

positive input

A2 P24V- Black

24 V power supply negative

input for both laser driver

and control board

1,3,4

2 C24V+ Red

24 V control board power

supply positive input

Yellow-green

GND

(4) Pin A1 & A2 are the positive and negative power line connector to the control board.

Pin 2 & A2 are the positive and negative power line connector to the laser driver.

During the operation, all the power connectors must be correctly connected, or laser

wouldn’t operate. Depending on the specific requirements in actual operation, the

control board and laser drive can be powered together or separately.

(5) During the operation, disconnection of any connect wire will lead the disable of laser

emission

(6) Make sure the control connector of external controller is compatible with the laser

device. Fix the control wire steady onto the laser control connector.

3 4 5 A2

User’s guide Ytterbium Pulsed Fiber Laser RFL-P20QB～P30QB Ver.: 2.0

3.Control Interface

There are DB9 and DB25 interfaces at the rear of the laser. The DB9 is a RS232 interface

only used for debugging, no needs to connect. And DB25 is the joint interface connecting control

system to the laser system, please make sure the connection is reliable before operation. Feet of

the DB25 are defined as follows in Fig. 5.

Figure 5. Connect port of controller.

Table 4 Definition of connect ports of controller.

PIN No.

Name

Description

1-8 (D0-D7) Power Setting

8 bits parallel port, D0 is minimum bit and

D7 is maximum bit;

Range: 0-255 (hexadecimal: 0x00-0xFF);

10,13-15,24-25

Ground

Digital GND.

11,12,16,21

Laser alarms status

See alarm codes in Table 4

17 VCC

+5VDC power supply input for independent

operation of the guide laser and PCB,

Maximum current consumption is 0.1A.

18 EE

Emission Enable (EE) signal.

HIGH: Emission Enable;

LOW or disconnected: Emission Disable.

19 EM

Emission Modulation (EM) input.

HIGH (>3V): Emission ON;

LOW or disconnected (<1V): Emission

OFF.

20 Sync

Pulse Repetition Rate (Synchronization)

input, square wave.

Guide Laser signal

Guide Laser (red diode) ON/OFF input.

User’s guide Ytterbium Pulsed Fiber Laser RFL-P20QB～P30QB Ver.: 2.0

9,23

Obligate PIN

Reserved.

(1) The pump current of diode laser and the laser output power are controlled by setting the

value of PIN1-PIN8 (TTL level). PIN1-PIN8 can be set from 0～255，corresponding to the

laser output power from 0～100％( the actual laser power may not be strictly linear with the

setting value). The relationship between PIN value and output power is shown in Table 4:

Table 5. Definition of power control PIN value.

Setting 1

Setting 2

Setting 3

Setting 4

PIN 1

PIN 2

PIN 3

PIN 4

PIN 5

PIN 6

PIN 7

PIN 8

Current

~50 %

~75 %

~87.5 %

~93.75 %

(2) PIN 17 is the external 5V input, providing power supply for alarm signal: input current＞

20mA.

(3) The external input signals (Pin 1-8, 18-20, 22) are connected to the optical coupler inside the

system. Input voltage 3V-5V are defined as digital High, below 1V are defined as digital

Low.

(4) Alarm setting: Pins 11, 12, 16 and 21 are the alarm and status outputs which driven by +5V

power from Pin 17. Pin 12 is reserved (always be high). These pins indicate the following

device states.

Table 6. Definition of alarm states.

PIN 12

PIN 11

PIN 16

PIN 21

Alarm item

×Low Low Low Temperature alarm

×Low Low High Normal

Low

High

Low

Obligate alarm

Low

High

System alarm

High

Low

Supply voltage

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Raycus Messgerät Handbücher

Raycus

Raycus RFL-C1000 Bedienungsanleitung

Raycus

Raycus RFL-C100 Bedienungsanleitung

Raycus

Raycus RFL-C1500H Bedienungsanleitung

Raycus

Raycus XZ Series Bedienungsanleitung

Raycus

Raycus RFL-A1000D Bedienungsanleitung

Raycus

Raycus RFL-P200 Bedienungsanleitung

Raycus

Raycus RFL-30QB Bedienungsanleitung

Raycus

Raycus RFL-C30000XZ Bedienungsanleitung

Raycus

Raycus RFL-A4000D Bedienungsanleitung

Raycus

Raycus RFL-C Series Bedienungsanleitung

Raycus

Raycus RFL-C4000XZ Bedienungsanleitung

Raycus

Raycus RFL-A500D Bedienungsanleitung

Raycus

Raycus RFL-C20000XZ Bedienungsanleitung

Raycus

Raycus RFL-A1500D Bedienungsanleitung

Raycus

Raycus RFL-A2000D Bedienungsanleitung

Raycus

Raycus ABP Series Bedienungsanleitung

Raycus

Raycus RFL-P20QS+ Montageanleitung

Raycus

Raycus RFL-P200S+ Montageanleitung

Raycus

Raycus A6000D Bedienungsanleitung

Raycus

Raycus RFL-A1000D Bedienungsanleitung

Raycus

Raycus RFL-C3000S Bedienungsanleitung

Raycus

Raycus RFL-P200MX Montageanleitung

Raycus

Raycus RFL-P70QA Montageanleitung

Raycus

Raycus RFL-P100MX Montageanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung