Raynor 8550WRGD Admiral II Bedienungsanleitung

CONTENTS

Preparation . . . . . . . . . . . . . . . .2-5

Assembly . . . . . . . . . . . . . . . . .6-7

Installation . . . . . . . . . . . . . . . 8-15

Install the Door Control. . . . . . 16-17

Install the Protector System®. . 18-21

Power. . . . . . . . . . . . . . . . . . 22-23

Adjustments . . . . . . . . . . . . . 24-26

Battery Backup. . . . . . . . . . . . 27-28

Operation . . . . . . . . . . . . . . . 29-35

Maintenance . . . . . . . . . . . . . . . 36

Troubleshooting. . . . . . . . . . . 37-38

Accessories. . . . . . . . . . . . . . . . 39

Warranty. . . . . . . . . . . . . . . . . . 40

Notes . . . . . . . . . . . . . . . . . . . . 41

Repair Parts . . . . . . . . . . . . . 42-43

WiFi®Garage

Door Opener

Raynor Garage Doors

1101 E. River Road

Dixon, Illinois 61021

■ Please read this manual and the enclosed safety materials carefully!

■ Fasten the manual near the garage door after installation.

■metsySrotcetorPehtsselnuESOLCTONLLIWroodehT ®is connected and properly

aligned.

■ Periodic checks of the garage door opener are required to ensure safe operation.

■QyMhtiwelbitapmocYLNOsireneporoodegaragsihT ®and Security+ 2.0™

accessories.

■roodegaragehtgnillatsnierauoyfierutaefesolC-ot-remiTehtelbaneTONOD

opener on a one-piece door. The Timer-to-Close is to be used ONLY with

sectional doors.

www.raynor.com

Model DGRW0558

DC Belt Drive with

Battery Backup

FOR RESIDENTIAL USE ONLY

SERIAL NUMBER:

Please write the MyQ Serial number in the box above. See page 2.

MyQ®Serial Number

Write down the following information for future reference:

MyQ®Serial Number:

MyQ®Serial Number

Accessory Setup Code Product S/N

Accessory Setup Code:

Product S/N:

Date of Purchase:

/ /

Safety Symbol and Signal Word Review

This garage door opener has been designed and tested to offer safe service provided it is installed,

operated, maintained and tested in strictaccordance with the instructions and warningscontained in this

manual.

When you see these Safety Symbols and Signal Words on the following pages,they will alertyou to the

possibility of serious injury or death if you do not comply with the warnings that accompany them. The

hazard may come from something mechanical or from electric shock. Read the warnings carefully.

Mechanical

Electrical

When you see thisSignal Word on the following pages, itwill alert you to the possibility ofdamage to

your garage door and/or the garage door opener ifyou do notcomplywith the cautionarystatementsthat

accompany it. Read them carefully.

Unattended Operation

The Timer-to-Close (TTC) feature, the MyQ®Smartphone Control app, and MyQ®Garage Door and

Gate Monitor are examples of unattended close and are to be used ONLY with sectional doors. Any

device or feature that allowsthe door to close without being in the line of sightof the door is considered

unattended close. The Timer-to-Close (TTC) feature, the MyQ®Smartphone Control,and anyother

MyQ®devices are to be used ONLY with sectional doors.

Preparation

Test the Wi-Fi®Signal Strength

Before You Begin

You will need:

lWi-Fi enabled smartphone, tablet or laptop

lBroadband Internet Connection

lWi-Fi®signal in the garage

lPassword for your home network

lMyQ Serial number (located on the garage door opener.)

Test the Wi-Fi®Signal Strength

Make sure your mobile device is connected to your Wi-Fi network.Hold your mobile device in the place

where your garage door opener will be installed and check the Wi-Fi signal strength.

Check Signal Strength. If you see:

Wi-Fi signal is strong.

The garage door opener will

connect to your Wi-Fi

network.

Wi-Fi signal is weak.

The garage door opener may connect

to your Wi-Fi network. If not, try one

of the options below to improve the

Wi-Fi signal:

No Wi-Fi signal.

The garage door opener will not be

able to connect to your Wi-Fi

network. Try one of the options

below to improve the Wi-Fi signal:

• Move your router closer to the garage

door opener to minimize interference from

walls and other objects

• Buy a Wi-Fi range extender

See page 31 to connect the garage door opener mobile device

Check the Door

To prevent possible SERIOUSINJURYor DEATH:

lALWAYS call a trained door systemstechnician if garage door binds, sticks, or is out of

balance.An unbalanced garage door mayNOT reverse when required.

lNEVER try to loosen, move or adjust garage door, door springs, cables, pulleys, brackets or

their hardware, ALLof which are under EXTREME tension.

lDisable ALLlocks and remove ALLropes connected to garage door BEFORE installation

and operating garage door opener to avoid entanglement.

To preventdamage to garage door and opener:

lALWAYS disable locks BEFORE installing and operating the opener.

lONLY operate garage door opener at120V,60Hz to avoid malfunction and damage.

1. Disable locks and remove any ropes connected to

the garage door.

2. Lift the door halfway up. Release the door. If

balanced, it should stay in place, supported entirely

by its springs.

3. Raise and lower the door to check for binding or

sticking. If your door binds, sticks, or is out of balance,

call a trained door systems technician.

4. Check the seal on the bottom ofthe door. Any gap

between the floor and the bottom of the door must not

exceed 1/4inch (6 mm). Otherwise, the safety

reversal system may not work properly.

5. The opener should be installed above the center of

the door.If there is a torsion spring or center bearing

plate in the wayof the header bracket, itmaybe

installed within 4feet (1.2m) to the leftor right ofthe

door center. See page9.

Torsion

Spring

Extension

Spring

Preparation

Tools Needed

3/16

5/32

5/16

7/16

1/2

5/8

9/16

1/4

7/16

Preparation

Carton Inventory

Accessorieswill vary depending on the garage door opener model purchased.Depending on your

specific model,other accessories may be included with your garage door opener.The instructions for

these accessorieswill be attached to the accessory and are not included in this manual. The images

throughout this manual are for reference and your product may look different.

A. Header bracket

B. Pulley and bracket

C. Door bracket

D. Curved door arm

E. Straight door arm

F. Trolley

G. Emergency release rope and handle

H. Rail

I. Garage door opener

J. Sprocket cover with hex screws

K. Belt

L. Door control (Smart Control Panel®41A3705)

M. White and red/white wire

N. The Protector System®

Safety reversing sensors with white and white/black wire attached: Sending senor

(1), receiving sensor (1), and safety sensor brackets (2)

O. Safety labels and literature

P. Rail grease

Q. Remote control model 893RGX

Assembly

Washered Bolt5/16"-18 x 1/2" (2) [mounted in the top of the garage door opener]

Installation

Hex Bolt 5/16"-18 x 7/8" (4) Lock Washer 5/16"-16 (4)

Lag Screw 5/16"-9 x 1-5/8" (2) Self-Threading Screw 1/4"-14 x 5/8" (2)

Clevis Pin 5/16" x 2-3/4" (1) Ring Fastener (3)

Clevis Pin 5/16" x 1-1/4" (1) Carriage Bolt 1/4"-20 x 1/2" (2)

Clevis Pin 5/16" x1" (1) Wing Nut 1/4"-20 (2)

Nut 5/16"-18 (4)

Door Control Hardware

Screw 6AB x 1-1/4" (2) Drywall Anchors (2)

Screw 6-32 x 1" (2) Insulated Staples

Not Provided

Not

Provided

Preparation

Assembly

1 Attach the Rail to the Garage Door Opener

To avoid possible SERIOUS INJURY to finger from moving garage door opener:

lALWAYS keep hand clear ofsprocket while operating opener.

lSecurely attach sprocket cover BEFORE operating.

To avoid SERIOUS damage to garage door opener,use ONLY those bolts/fasteners mounted in the

top of the opener.

NOTE: ONLY use the bolts removed fromthe garage door opener.Place the garage door opener on

the packing material to prevent scratching.

1. Remove the two boltsfromthe top ofthe garage door opener.

2. Align the rail and the styrofoam over the sprocket.Cutthe tape from the rail, belt, and

styrofoam.

3. Fasten the rail with the previouslyremoved bolts.

4. Position the beltaround the garage door opener sprocket.

5. Attach the sprocket cover over the garage door opener sprocket and attach with hex screws.

Model 8550W

Model 8557W

Washered Bolt

5/16"-18x1/2"

Hex Screw

#8x3/8"

Lock Nut

Washered Bolt 5/16"-18x1/2"

(Mounted in the garage

door opener)

Hex Screw

#8x3/8"

(Packed with the

sprocket cover)

Washered Bolt

5/16"-18x1/2"

Hex Screw

#8x3/8"

HARDWARE

Assembly

2 Tighten the Belt

1. By hand, thread the spring trolley nut on the threaded shaft until it isfinger tight againstthe

trolley. Do not use any tools.

2. Inserta flathead screwdriver tip into one ofthe nut ring slots and brace it firmlyagainst the

trolley.

3. Tighten the spring trolley nutwith an adjustable wrench or a 7/16" open end wrench about a

quarter turn until the spring releasesand snaps the nutring against the trolley.Thissets the

spring to optimum belt tension.

Spring Trolley Nut

(To motor unit)

Nut ring

slot

Nut Ring Nut Ring

AFTER RELEASE

1-1/4"

(3.18 cm)

BEFORE

(2.5 cm)

Installation

IMPORTANT INSTALLATION INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS.

2. Install garage door opener ONLY on properlybalanced and lubricated garage door. An

improperly balanced door may NOTreverse when required and could resultin SEVERE

INJURY or DEATH.

3. ALL repairs to cables, spring assemblies and other hardware MUST be made by a trained

door systems technician BEFORE installing opener.

4. Disable ALL locksand remove ALL ropesconnected to garage door BEFORE installing

opener to avoid entanglement.

5. Install garage door opener 7 feet(2.13 m) or more above floor.

6. Mount the emergency release within reach, but at least 6 feet (1.83 m) above the floor and

avoiding contact with vehicles to avoid accidental release.

7. NEVER connect garage door opener to power source until instructed to do so.

8. NEVERwear watches,rings or loose clothing while installing or servicing opener.They

could be caughtin garage door or opener mechanisms.

9. Install wall-mounted garage door control:

lwithin sight of the garage door.

lout of reach of children at minimum height of 5 feet (1.5 m).

laway from ALL moving parts of the door.

10. Place entrapment warning label on wall next to garage door control.

11. Place manual release/safety reverse test label in plain view on inside of garage door.

12. Upon completion of installation, test safety reversal system. Door MUST reverse on contact

with a 1-1/2" (3.8 cm) high object (or a 2x4 laid flat) on the floor.

13. To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution, disconnect ALL

electric and battery power BEFORE performing ANY service or maintenance.

14. DO NOT enable the Timer-to-Close functionality if operating either one-piece or swinging

garage doors.To be enabled ONLY when operating a sectional door.

Installation

1 Determine the Header Bracket Location

To prevent possible SERIOUS INJURY or DEATH:

lHeader bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling,

otherwise garage door might NOT reverse when required. DO NOT install header bracket

over drywall.

lConcrete anchors MUST be used ifmounting header bracket or 2x4 into masonry.

lNEVER try to loosen, move or adjust garage door, springs,cables,pulleys,brackets, or their

hardware, ALL of which are under EXTREME tension.

lALWAYS call a trained door systemstechnician if garage door binds, sticks,or is out of

balance. An unbalanced garage door mightNOT reverse when required.

lDO NOT enable the Timer-to-Close functionality if operating either one-piece or swinging

garage doors.To be enabled ONLY when operating a sectional door.

Close the door and mark the inside vertical centerline ofthe garage door.

Extend the line onto the header wall above the door. You can fasten the header bracketwithin 4 feet

(1.22 m) of the leftor right ofthe door center onlyif a torsion spring or center bearing plate isin the way;

or you can attach it to the ceiling when clearance is minimal.(Itmaybe mounted on the wall upside down

if necessary, to gain approximately 1/2" (1 cm). If you need to install the header bracket on a 2x4 (on wall

or ceiling),use lag screws(not provided) to securely fasten the 2x4 to structural supports.

Open your door to the highestpointof travel asshown. Draw an intersecting horizontal line on the

header wall 2" (5 cm) above the high point. This height will provide travel clearance for the top edge of

the door.

NOTE: If the total number of inches exceeds the height available in your garage, use the maximum

height possible, or refer to page 10 for ceiling installation.

Header Wall

Unfinished

Ceiling

Vertical Centerline

of Garage Door

2x4

Structural

Supports

Level

(Optional)

OPTIONAL

CEILING

MOUNT FOR

HEADER

BRACKET

Sectional door with curved track

Header Wall

Track

2" (5 cm)

Highest Point

of Travel

Door

Installation

2 Install the Header Bracket

You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the

instructions which will work best for your particular requirements. Do not install the header bracket over

drywall. If installing into masonry, use concrete anchors (not provided).

HARDWARE

Lag Screw 5/16"-9x1-5/8"

OPTION A WALL INSTALLATION

1. Center the bracket on the vertical centerline with the bottom edge of the bracket on the

horizontal line as shown (with the arrowpointing toward the ceiling).

2. Mark the vertical set of bracket holes (do not use the holes designated for ceiling mount). Drill

3/16" pilot holes and fasten the bracket securely to a structural supportwith lag screws.

Wall Mount

Optional

Mounting

Holes

Vertical

Centerline of

Garage Door

(Header Wall)

Header

Bracket

2x4 Structural

Support

Door Spring

(Garage Door)

Highest Point of

Garage Door

Travel

Horizontal

Line

Lag Screw

5/16" - 9 x 1-5/8"

OPTION B CEILING INSTALLATION

1. Extend the vertical centerline onto the ceiling as shown.

2. Center the bracket on the vertical mark, no more than 6" (15 cm) from the wall. Make sure the

arrow is pointing toward the wall. The bracket can be mounted flush against the ceiling when

clearance is minimal.

3. Mark the side holes. Drill 3/16" pilot holes and fasten bracket securely to a structural support

with lag screws.

(Header Wall)

Ceiling Mounting Holes

(Finished Ceiling)

Vertical

Centerline of

Garage Door

Header

Bracket

6" (15 cm)

Maximum

Door Spring

(Garage Door)

Lag Screw

5/16" - 9 x 1-5/8"

Inhaltsverzeichnis

Andere Raynor Garagentoröffner Handbücher

Raynor

Raynor 87504RGD-267 Bedienungsanleitung

Raynor

Raynor RapidCoil RC300 Series Bedienungsanleitung

Raynor

Raynor Ultra II 8587RGD Bedienungsanleitung

Raynor

Raynor 545RGD Safety Signal Bedienungsanleitung

Raynor

Raynor Commander II Safety Signal 3240RGD Bedienungsanleitung

Raynor

Raynor U:TRA II 8587WRGD Bedienungsanleitung

Raynor

Raynor COMMANDER 2000RGD Bedienungsanleitung

Raynor

Raynor Safety Signal 3800RGD Bedienungsanleitung

Raynor

Raynor 8500WRGD Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

Raynor

Raynor 8165RGD CONTRACTOR Series Corporal II Bedienungsanleitung

Raynor

Raynor PILOT 2265RGD Bedienungsanleitung

Raynor

Raynor FliteStar-7 Bedienungsanleitung

Raynor

Raynor Safety signal 3220RGD Bedienungsanleitung

Raynor

Raynor 2220RGD 1/2 HP Bedienungsanleitung

Raynor

Raynor 3595RGD 3/4 HP Bedienungsanleitung

Raynor

Raynor Sergeant II STANDARD Series Bedienungsanleitung

Raynor

Raynor ControlHoist ATS2113X-CX Bedienungsanleitung

Raynor

Raynor Pilot 1265RGD Bedienungsanleitung

Raynor

Raynor Navigator 2245RGD Bedienungsanleitung

Raynor

Raynor ULTRA 3595RGDS 3/4 HP Bedienungsanleitung

Raynor

Raynor Sergeant II Standard 8160WRGD Bedienungsanleitung

Raynor

Raynor Premium series 8500RGD Prodigy II Bedienungsanleitung

Raynor

Raynor Navigator 1245RGD Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Chamberlain

Chamberlain Elite 3575S Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Chamberlain

Chamberlain MyQ 940ESTD Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Chamberlain

Chamberlain HD520EVP Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Chamberlain

Chamberlain 8355 - 1/2 hp Bedienungsanleitung