Raynor 8165RGD CONTRACTOR Series Corporal II Bedienungsanleitung

CONTENTS

Preparation . . . . . . . . . . . . . . . .1-2

Assembly . . . . . . . . . . . . . . . . . . 3

Installation . . . . . . . . . . . . . . . 4-11

Install the Door Control. . . . . . 12-13

Install the Protector System®. . 14-17

Power. . . . . . . . . . . . . . . . . . 18-19

Adjustments . . . . . . . . . . . . . 20-22

Operation . . . . . . . . . . . . . . . 23-28

Maintenance . . . . . . . . . . . . . . . 29

Troubleshooting. . . . . . . . . . . 30-31

Accessories. . . . . . . . . . . . . . . . 32

Warranty. . . . . . . . . . . . . . . . . . 33

Repair Parts . . . . . . . . . . . . . 34-35

CONTRACTOR Series

1/2 hp Chain Drive

Garage Door Opener

Raynor Garage Doors

1101 E. River Rd.

Dixon, Illinois 61021

■ Please read this manual and the enclosed safety materials carefully!

■ Fasten the manual near the garage door after installation.

■The door WILL NOT CLOSE unless the Protector System®is connected and properly

aligned.

■ Periodic checks of the garage door opener are required to ensure safe operation.

■The model number label is located on the front panel of your garage door opener.

■This garage door opener is ONLY compatible with MyQ®Security+ 2.0™

accessories.

■ONLY enable the Timer-to-Close or MyQ®remote operation feature when the

garage door opener is installed on a sectional door.

NOTE: If you are installing the garage door opener on a one-piece door, visit

www.raynor.com for installation instructions.

www.raynor.com

Serial Number:

Date of Purchase:

Model 8165RGD

FOR RESIDENTIAL USE ONLY

Write down the following information for

future reference:

Safety Symbol and Signal Word

Review

Thisgarage door opener hasbeen designed and

tested to offer safe service provided itis installed,

operated,maintained and tested in strict

accordance with the instructionsand warnings

contained in this manual.

When you see these Safety Symbols and Signal

Words on the following pages, they will alertyou to

the possibility of serious injury or death if you do

not comply with the warnings that accompany them.

The hazard maycome from something mechanical

or from electricshock.Read the warnings carefully.

Mechanical

Electrical

When you see thisSignal Word on the following

pages, it will alert you to the possibility of damage to

your garage door and/or the garage door opener if

you do not comply with the cautionary statements

that accompany it. Read them carefully.

Check the Door

To prevent possible SERIOUSINJURYor

DEATH:

lALWAYS call a trained door systems

technician if garage door binds,sticks,

or isoutofbalance.An unbalanced

garage door mayNOTreverse when

required.

lNEVER tryto loosen,move or adjust

garage door,door springs,cables,

pulleys,bracketsor their hardware,

ALLof which are under EXTREME

tension.

lDisable ALLlocks and remove

ALLropesconnected to garage door

BEFORE installation and operating

garage door opener to avoid

entanglement.

To preventdamage to garage door and opener:

lALWAYS disable locks BEFORE

installing and operating the opener.

lONLY operate garage door opener at

120V, 60 Hz to avoid malfunction and

damage.

1. Disable locks and remove any ropes

connected to the garage door.

2. Lift the door halfway up. Release the

door. If balanced, it should stay in place,

supported entirely by its springs.

3. Raise and lower the door to check for

binding or sticking. Ifyour door binds,

sticks, or is out of balance, call a trained

door systems technician.

4. Check the seal on the bottom ofthe door.

Any gap between the floor and the

bottom of the door must not exceed

1/4inch (6 mm). Otherwise, the safety

reversal system may not work properly.

5. The opener should be installed above

the center ofthe door. Ifthere isa torsion

spring or center bearing plate in the way

of the header bracket, it may be installed

within 4 feet(1.2 m) to the left or right of

the door center.See page 5.

Torsion

Spring

Extension

Spring

Tools Needed

3/16

7/16

1/2

5/32

5/16

5/8

9/16

1/4

7/16

Preparation

Carton Inventory

Accessorieswill varydepending on the garage door opener model purchased.Depending on your

specificmodel, other accessoriesmay be included with your garage door opener. The instructions for

these accessories will be attached to the accessory and are not included in this manual. The images

throughout this manual are for reference and your product may look different.

A. Header bracket

B. Pulley and bracket

C. Door bracket

D. Curved door arm

E. Straight door arm

F. Trolley

G. Emergencyrelease rope and handle

H. Rail

I. Garage door opener

J. Sprocket cover

K. Chain

L. Door control

M. White and red/white wire

N. The Protector System®

Safety reversing sensors with white and white/blackwire attached: Sending Sensor (1)

Receiving Sensor (1) and SafetySensor Brackets (2)

O. Safety labels and literature

P. Rail grease

Security+ 2.0™ Accessories

041A7185-2

Multi-Function Door Control

891RGD

Remote Control

Hardware

Installation Door Control Hardware

Hex bolt 5/16"-18 x 7/8" (4) Screw 6AB x 1" (2)

Lag screw 5/16"-9 x 1-5/8" (2) Screw 6-32 x 1" (2)

Clevis Pin 5/16" x 2-3/4" (1) Drywall anchors (2)

Clevis Pin 5/16" x 1-1/4" (1) Insulated staples

Clevis Pin 5/16" x 1" (1)

Nut 5/16"-18 (4)

Lock washer 5/16" (4)

Self-threading screw 1/4"-14 x 5/8" (2)

Ring fastener (3)

Carriage bolt 1/4"-20 x 1/2" (2)

Wing nut 1/4"-20 (2)

Not Provided

Not

Provided

Preparation

Assembly

1 Attach the Rail to the Garage Door Opener

To avoid possible SERIOUS INJURY to finger from moving garage door opener:

lALWAYS keep hand clear of sprocket while operating opener.

lSecurely attach sprocket cover BEFORE operating.

To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the

top ofthe opener.

NOTE: ONLY use the boltsremoved from the garage door opener.Place the garage door opener on

the packing material to prevent scratching.

1. Remove the two boltsfrom the top ofthe garage door opener.

2. Align the rail and the styrofoam over the sprocket.Cutthe tape from the rail, chain,and

styrofoam.

3. Fasten the rail with the previously removed bolts.

4. Position the chain around the garage door opener sprocket.

5. Install the sprocket cover by squeezing the sides and inserting the tabs into the slots on the

garage door opener.

Washered Bolt 5/16"-18x1/2"

(Mounted in the garage door opener)

2 Tighten the Chain

1. Loosen the inner nut and lockwasher on the trolleythreaded shaft.

2. Tighten the outer nut until the chain is a 1/2 inch above the base of the rail at the midpointof

the rail.

3. Re-tighten the inner nut.

Slack in the chain is normal when the door is closed. No readjustment isnecessary.

NOTE: Sprocket noise can result if the chain is too loose. During future maintenance, ALWAYS pull the

emergency release handle to disconnect the trolley before adjusting the chain.

1/2"

Installation

IMPORTANT INSTALLATION INSTRUCTIONS

WARNING

To reduce the risk of SEVERE INJURY or DEATH:

1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS.

2. Install garage door opener ONLY on properlybalanced and lubricated garage door.An

improperly balanced door may NOT reverse when required and could resultin SEVERE

INJURY or DEATH.

3. ALL repairsto cables,spring assemblies and other hardware MUSTbe made by a trained

door systemstechnician BEFORE installing opener.

4. Disable ALL locks and remove ALL ropesconnected to garage door BEFORE installing

opener to avoid entanglement.

5. Install garage door opener 7 feet (2.13 m) or more above floor.

6. Mount the emergency release within reach, butat least6 feet (1.83 m) above the floor and

avoiding contact with vehicles to avoid accidental release.

7. NEVER connect garage door opener to power source until instructed to do so.

8. NEVERwear watches,rings or loose clothing while installing or servicing opener. They could

be caughtin garage door or opener mechanisms.

9. Install wall-mounted garage door control:

lwithin sight of the garage door.

lout of reach of children at minimum height of 5 feet (1.5 m).

laway from ALL moving parts of the door.

10. Place entrapment warning label on wall nextto garage door control.

11. Place manual release/safetyreverse testlabel in plain view on inside ofgarage door.

12. Upon completion of installation, test safety reversal system. Door MUST reverse on contact

with a 1-1/2" (3.8 cm) high object(or a 2x4 laid flat) on the floor.

13. To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution, disconnectALL

electric power BEFORE performing ANY service or maintenance.

14. DO NOT enable the Timer-to-Close functionalityif operating either one-piece or swinging

garage doors.To be enabled ONLY when operating a sectional door.

NOTE: If you are installing the garage door opener on a one-piece door, visit www.raynor.com for installation instructions.

Installation

1 Determine the Header Bracket Location

To prevent possible SERIOUS INJURY or DEATH:

lHeader bracketMUSTbe RIGIDLY fastened to structural support on header wall or ceiling,

otherwise garage door might NOT reverse when required. DO NOT install header bracket

over drywall.

lConcrete anchors MUST be used if mounting header bracketor 2x4 into masonry.

lNEVER try to loosen, move or adjust garage door, springs, cables, pulleys, brackets, or their

hardware, ALL of which are under EXTREME tension.

lALWAYS call a trained door systems technician if garage door binds,sticks, or is outof

balance. An unbalanced garage door mightNOT reverse when required.

lDO NOT enable the Timer-to-Close functionalityifoperating either one-piece or swinging

garage doors. To be enabled ONLY when operating a sectional door.

NOTE: If you are installing the garage door opener on a one-piece door, visit www.raynor.com for

installation instructions.

Close the door and mark the inside vertical centerline of the garage door.

Extend the line onto the header wall above the door.You can fasten the header bracket within 4 feet

(1.22 m) of the left or right ofthe door center only if a torsion spring or center bearing plate is in the way;

or you can attach it to the ceiling when clearance is minimal. (Itmay be mounted on the wall upside down

if necessary,to gain approximately 1/2" (1 cm).Ifyou need to install the header bracket on a 2x4 (on wall

or ceiling),use lag screws (not provided) to securely fasten the 2x4 to structural supports.

Open your door to the highest point of travel as shown.Draw an intersecting horizontal line on the

header wall 2" (5 cm) above the high point. This heightwill provide travel clearance for the top edge of

the door.

NOTE: If the total number of inches exceeds the height available in your garage, use the maximum

height possible, or refer to page 6 for ceiling installation.

Header Wall

Unfinished

Ceiling

Vertical Centerline

of Garage Door

2x4

Structural

Supports

Level

(Optional)

OPTIONAL

CEILING

MOUNT FOR

HEADER

BRACKET

Sectional door with curved track

Header Wall

Track

2" (5 cm)

Highest Point

of Travel

Door

Installation

2 Install the Header Bracket

You can attach the header bracketeither to the wall above the garage door,or to the ceiling. Follow the

instructions which will workbestfor your particular requirements. Do not install the header bracket over

drywall. If installing into masonry, use concrete anchors (not provided).

HARDWARE

Lag Screw 5/16"-9x1-5/8"

OPTION A WALL INSTALLATION

1. Center the bracket on the vertical centerline with the bottom edge of the bracket on the

horizontal line as shown (with the arrow pointing toward the ceiling).

2. Mark the vertical setofbracket holes (do not use the holes designated for ceiling mount).Drill

3/16" pilot holes and fasten the bracketsecurely to a structural support with lag screws.

Wall Mount

Optional

Mounting

Holes

Vertical

Centerline of

Garage Door

(Header Wall)

Header

Bracket

2x4 Structural

Support

Door Spring

(Garage Door)

Highest Point of

Garage Door

Travel

Horizontal

Line

Lag Screw

5/16" - 9 x 1-5/8"

OPTION B CEILING INSTALLATION

1. Extend the vertical centerline onto the ceiling as shown.

2. Center the bracket on the vertical mark,no more than 6" (15 cm) from the wall. Make sure the

arrow is pointing toward the wall. The bracketcan be mounted flush againstthe ceiling when

clearance is minimal.

3. Mark the side holes.Drill 3/16" pilot holes and fasten bracketsecurely to a structural support

with lag screws.

(Header Wall)

Ceiling Mounting Holes

(Finished Ceiling)

Vertical

Centerline of

Garage Door

Header

Bracket

6" (15 cm)

Maximum

Door Spring

(Garage Door)

Lag Screw

5/16" - 9 x 1-5/8"

Installation

3 Attach the Rail to the Header Bracket

1. Align the rail with the header bracket. Insert the clevispin through the holes in the header

bracket and rail. Secure with the ring fastener.

NOTE: Use the packing material as a protective base for the garage door opener.

HARDWARE

Clevis Pin 5/16" x 2-3/4" Ring Fastener

Ring

Fastener

Clevis Pin

5/16" X 2-3/4"

4 Position the Garage Door Opener

To preventdamage to garage door,restgarage door opener rail on 2x4 placed on top section of

door.

1. Remove the packing material and lift the garage door opener onto a ladder.

2. Fully open the door and place a 2x4 (laid flat) under the rail.

A 2x4 isideal for setting the distance between the rail and the door. Ifthe ladder is not tall enough you

will need help at this point.Ifthe door hits the trolley when it israised, pull the trolley release arm down to

disconnect the inner and outer trolley.Slide the outer trolley toward the garage door opener. The trolley

can remain disconnected until instructed.

Connected Disconnected

Installation

5 Hang the Garage Door Opener

To avoid possible SERIOUS INJURY from a falling garage door opener,fasten it SECURELY to

structural supportsofthe garage.Concrete anchors MUST be used if installing ANY bracketsinto

masonry.

Hanging your garage door opener will vary depending on your garage. Two representative installations

are shown.Yours may be different.Hanging bracketsshould be angled (Figure 1) to provide rigid

support.On finished ceilings (Figure 2),attach a sturdy metal bracketto structural supports before

installing the opener. This bracket and fastening hardware are not provided.

1. Measure the distance from each side ofthe motor unit to the structural support.

2. Cutboth pieces ofthe hanging bracket to required lengths.

3. Drill 3/16" pilotholes in the structural supports.

4. Attach one end of each bracketto a support with 5/16"-18x1-7/8" lag screws(notprovided).

5. Fasten the opener to the hanging bracketswith 5/16"-18x7/8" hex bolts,lock washers and

nuts.

6. Check to make sure the rail is centered over the door (or in line with the header bracket ifthe

bracket isnot centered above the door).

7. Remove the 2x4.Operate the door manually. Ifthe door hits the rail, raise the header bracket.

NOTE: DO NOT connect power to opener at this time.

FIGURE 1 FIGURE 2

(Not Provided)

Lag Screws

5/16"- 18x1-7/8"

Measure

Distance

Hex Bolt 5/16"- 18x7/8", Lock Washer 5/16", Nut 5/16"-18

FIGURE 3

Not Provided

Finished Ceiling

Unﬁnished Ceiling

Hex Bolt 5/16"- 18x7/8" Nut 5/16"-18Lock Washer 5/16"

HARDWARE

Installation

6 Install the Light Bulbs

To prevent possible OVERHEATING of the endpanel or light socket:

lDO NOT use short neck or specialty light bulbs.

lDO NOT use halogen bulbs.Use ONLY incandescent.

To preventdamage to the opener:

lDO NOT use bulbslarger than 100W.

lONLY use A19 size bulbs.

1. Press the release tabs on both sides of lens.Gently rotate lens back and downward until the

lens hinge isin the fully open position.Do not remove the lens.

2. Install a 100 watt maximum light bulb in each socket.Light bulb size should be A19,standard

neckonly. The lights will turn ON and remain lit for approximately 4-1/2 minuteswhen power is

connected. Then the lightswill turn OFF.

3. Reverse the procedure to close the lens.

4. If the bulbsburn out prematurely due to vibration, replace with a Garage Door Opener bulb.

5. Use A19, standard neckgarage door opener bulbsfor replacement.

NOTE: Use only standard light bulbs. The use of short neck or specialty light bulbs may overheat the

endpanel or light socket.

100 Watt (Max)

Standard Light Bulb

Release Tab

Lens Hinge

7 Attach the Emergency Release Rope and Handle

To preventpossible SERIOUS INJURY or DEATH froma falling garage door:

lIf possible, use emergency release handle to disengage trolley ONLY when garage door is

CLOSED. Weak or broken springs or unbalanced door could result in an open door falling

rapidlyand/or unexpectedly.

lNEVER use emergency release handle unless garage doorway is clear of persons and

obstructions.

lNEVER use handle to pull door open or closed. Ifrope knotbecomesuntied, you could fall.

1. Insert one end ofthe emergency release rope through the handle.Make sure that “NOTICE” is

rightside up. Tie a knotatleast 1 inch (2.5 cm) from the end of the emergency release rope.

2. Insert the other end of the emergencyrelease rope through the hole in the trolley release arm.

Mount the emergency release within reach, butat least6 feet (1.83 m) above the floor,

avoiding contact with vehicles to prevent accidental release and secure with a knot.

NOTE: If it is necessary to cut the emergency release rope, seal the cut end with a match or lighter to

prevent unraveling. Ensure the emergency release rope and handle are above the top of all vehicles to

avoid entanglement.

Trolley

Release Arm

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Raynor Garagentoröffner Handbücher

Raynor

Raynor Sergeant II Standard 8160WRGD Bedienungsanleitung

Raynor

Raynor ULTRA SAFETY SIGNAL 2595RGD Bedienungsanleitung

Raynor

Raynor 3595RGD 3/4 HP Bedienungsanleitung

Raynor

Raynor 8550WRGD Admiral II Bedienungsanleitung

Raynor

Raynor RapidCoil RC300 Series Bedienungsanleitung

Raynor

Raynor FliteStar-7 Bedienungsanleitung

Raynor

Raynor Airman II 8155RGD Bedienungsanleitung

Raynor

Raynor Navigator 2245RGD Bedienungsanleitung

Raynor

Raynor SENTINEL III 84505RRGD Bedienungsanleitung

Raynor

Raynor MT5011UCHB Bedienungsanleitung

Raynor

Raynor U:TRA II 8587WRGD Bedienungsanleitung

Raynor

Raynor ULTRA 3595RGDS 3/4 HP Bedienungsanleitung

Raynor

Raynor MJ5011UCHB Bedienungsanleitung

Raynor

Raynor COMMANDER 2000RGD Bedienungsanleitung

Raynor

Raynor ControlHoist ATS2113X-CX Bedienungsanleitung

Raynor

Raynor 545RGD Safety Signal Bedienungsanleitung

Raynor

Raynor 2220RGD 1/2 HP Bedienungsanleitung

Raynor

Raynor Navigator 1245RGD Bedienungsanleitung

Raynor

Raynor 8500WRGD Bedienungsanleitung

Raynor

Raynor Aviator II PREMIUM Series Gebrauchs- und Pflegehandbuch

Raynor

Raynor CORPORAL II STANDARD Series Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

Raynor

Raynor 3265RGDM 1/2 HP Bedienungsanleitung

Raynor

Raynor Safety signal 3220RGD Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Chamberlain

Chamberlain Elite 3575S Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Chamberlain

Chamberlain MyQ 940ESTD Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Chamberlain

Chamberlain HD520EVP Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Chamberlain

Chamberlain 8355 - 1/2 hp Bedienungsanleitung