Raypak PROTÉGÉ RPAGP Betriebsanleitung

018225F

018226F

P/N 241841 Rev 2

E󰀨ective: 08-14-2020

Replaces: 1-6-2020

RAYPAK SERVICE INSTRUCTIONS

PROTÉGÉ SERIES PUMP AND FILTER RPAGP, RPSFP, RPCFP

KIT 018225F, LOCK RING, CLEAR LID AND O-RING

KIT 018226F, BASKET

Scope

These kits provide the parts required to replace the lock

ring assembly and basket for the Protégé Line of pumps

and lters.

Kit 018225F

Components

Lock Ring, Clear Lid, O-ring

Kit 018226F

Components

Basket

Required Tools

• None

Recommended Materials

• Any quality generic brand of appropriate lubricant

for application onto O-rings and threads of plastic

parts such as "Water Lube".

DANGER – SHOCK HAZARD: Make sure electrical power to attached pump and

heaters is disconnected to avoid damage to components, potential serious personal

injury or death.

WARNING: Make sure water & power have been turned OFF before making any re-

pairs or service to the unit.

IMPORTANT NOTICE: These instructions are for the use of qualied individuals

specially trained and experienced in the installation and maintenance of this type of

equipment and related system components. Installation and service personnel are re-

quired by some states to be licensed. Persons not qualied shall not attempt to install,

service, or maintain this equipment.

Replacing Lock Ring, Clear Lid,

and Basket

1. Turn off the electrical power at the Pump’s power

switch and/or unplug it at the receptacle.

2. Allow the pump motor to cool down before servicing

the unit.

3. Close the water valves, if installed, to isolate the

pump from the system.

4. Gently push the lock ring counter-clockwise to unlock

the clear pump lid as shown in Figure 1. Once the

clear ring is loose, remove the lock ring by lifting it

straight up. Set it aside as shown in Figure 2.

Figure 1. Lock Ring Removal Rotational Direction

Figure 2. Lock Ring Removal, Lift Up and Out

5. The clear lid is threaded to the pump lint pot. Turn the

lid counter-clockwise about two and a half times to

unlock. It will lift up and out as shown in Figure 3

Figure 3. Clear Lid Removal

6. Lift the Lint basket straight up and out as shown

in Figure 4. The basket is keyed. Later on, when

it's time to reassemble things using the new parts,

align the grooves with the guide ridges cast into the

housing as shown in Figure 5.

Figure 4. Lint Basket Removal

Figure 5. Lint Basket Guide Keys

Raypak, Inc., 2151 Eastman Avenue, Oxnard, CA 93030 1-800-260-2758 Fax (805) 278-5468

7. In order to reassemble these components properly,

use a generous amount of suitable lubricant for the

silicone rubber O-ring that is seated at the top of the

pump’s lint pot as shown in Figure 6.

Figure 6. Silicone Rubber O-Ring

8. Reverse steps 6 to 1 in order to assemble and

operate the pump using the new kit parts.

Dieses Handbuch passt für folgende Modelle

Andere Raypak Wasserpumpe Handbücher

Raypak

Raypak PS270VSP Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung