RDM Connect EC9001 Bedienungsanleitung
RDM Connect™ Installation Guide
Revision B
RDM Connect™ Installation Guide Rev. B
Revised: November 30, 2012
© 2012 RDM Corporation
This manual, the RDM Connect™ Installation Guide, is intended for all units belonging to the Connect family of products.
Trad em ar ks
RDM Connect is a trademark of RDM Corporation. RDM and the RDM logo are registered trademarks of RDM Corporation. All other brand names and trademarks appearing in this
guide are the property of their respective holders.
All rights reserved. No part of this document may be reproduced in any form without the written consent of RDM Corporation.
Part Number
302935
RDM Corporation
www.rdmcorp.com
i
Contents
Compliance Statements .................................................................................................................................. 1
Introduction ...................................................................................................................................................... 3
RDM Connect Models and Features ............................................................................................................... 4
Setting Up the RDM Connect Scanner ............................................................................................................ 5
Operating the Scanner .................................................................................................................................. 17
Maintaining the RDM Connect Scanner ........................................................................................................ 22
Troubleshooting ............................................................................................................................................. 24
Specifications ................................................................................................................................................ 25
Warranty Information ..................................................................................................................................... 27
ii
1
Compliance Statements
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Warning: Changes or modifications not expressly approved by RDM could void the user’s authority to operate the equipment.
All units covered by this manual have no user-serviceable parts inside. In the event repairs are ever needed to any RDM product, they should be
performed by RDM Corporation or an authorized representative of RDM Corporation. For information please contact RDM Corporation,
4-608 Weber Street North, Waterloo, Ontario, Canada N2V 1K4, at 1-800-567-6227, or RDM’s US service agent below.
US Service Agent
William Buser
(703) 286-5734
2
3
Introduction
The RDM Connect™ scanner is a cost-effective, feature-rich, source item image and card processing solution. Using RDM’s
industry leading progressive MICR method and imaging technology, the RDM Connect scanner is ideal for Check
Electronification, Check Cashing, and Walk-in Bill Payment applications. The RDM Connect scanner provides Remote Deposit
Capture features as well as features that are suitable for card-based processing.
Requirements
• The RDM Connect unit is for indoor use only. Keep the RDM Connect dry; avoid areas of high humidity.
•Do not remove any cabinetry other than the areas specified in this guide. Removing cabinetry other than the areas specified in
this guide will void the warranty.
Recommendations
• This unit may be installed and configured by a distributor (reseller) other than the original manufacturer. Record all distributor
contact information for future reference.
•Save the original box and packing material. Reuse them if the unit must be shipped to a new location.
•Position the unit so that the operator has easy access to the document path and a clear view of the LED. Do not put the unit
close to a heat source, in direct sunlight, or close to any device that can emit electromagnetic interference, such as a computer
monitor or power adapter.
4
RDM Connect Models and Features
The RDM Connect scanner comes in several different models. Each model includes a certain set of features. Compare your model
to the following list to determine which features are included with your scanner.
RDM Connect Launch Button
The RDM Connect scanner launch button is a hotkey that can be set to open a
document or Web site, or start an application. Your RDM Connect launch button has
been configured according to the requirements of your application.
Developers can find information about programming the launch button in the Help
File that is included with the ADK.
In addition, the launch button indicates the status of the scanner with its illuminated
LED. For more information, see “Status Signals” on page 20.
The launch button is labelled with the RDM Connect logo. If you want your own logo
applied to the launch button, contact your solution provider or reseller for details.
Model Description
EC9001 Auto-Feed scanner (Franker and Card Scan Enabled
EC9002 Auto-Feed scanner (Franker and Card Scan Enabled) with MSR
EC9003 Auto-Feed scanner (Franker and Card Scan Enabled) with Endorser
EC9004 Auto-Feed scanner (Franker and Card Scan Enabled) with Endorser and MSR
EC9011 Single Feed scanner (Franker and Card Scan Enabled
EC9012 Single Feed scanner (Franker and Card Scan Enabled) with MSR
EC9013 Single Feed scanner (Franker and Card Scan Enabled) with Endorser
EC9014 Single Feed scanner (Franker and Card Scan Enabled) with Endorser and MSR
5
Setting Up the RDM Connect Scanner
To set up the RDM Connect scanner, do the following:
• Choose a Location
• Unpack the Shipping Box
• Inspect the Unit’s Features
• Insert the Franking Acknowledgement Printer and Endorser
Inkjet Printer Cartridges, if they are included on your scanner.
Choose a Location
Locate your scanner in a place that:
• Has a flat surface, such as a counter top or table.
• Is convenient for the scanner operator.
• Offers adequate ventilation and protection from elements such as heat, dust, oil, or moisture.
• Is close to the hosting PC (USB 2.0 high speed connection required).
• Is close to a power supply.
Unpack the Shipping Box
1. Open the top of the box.
2. Remove and unwrap the items.
3. Save the box and packing material for future use.
Check List
Your shipping box should include the following items:
• RDM Connect scanner
• USB cable
• Power supply
• (Optional) Franking and acknowledgement printer
• (Optional) Inkjet cartridge
6
Inspect the Unit’s Features
Driver’s License or
ID Card Entry
Imaging Slot
Insertion Hopper
Exit Pocket
Application Launch
Button and Scanner
Status LED
3-Track Bi-directional
Magnetic Stripe Reader
Insertion Extension
Exit Extension
Dieses Handbuch passt für folgende Modelle
7
Inhaltsverzeichnis
