RDM EC6000i Series Bedienungsanleitung
EC6000i®, EC7000i®, and EC7500i®
Series Installation Guide
This manual, the EC6000i , EC7000i, and EC7500i Series Installation Guide, is intended for all units
belonging to the EC6000i, EC7000i, and EC7500i family of products.
EC6000i, EC7000i, EC7500i, ITMS, RDM, and the RDM logo are all registered trademarks of RDM
Corporation. All other brand names and trademarks appearing in this guide are the property of their
respective holders.
Copyright© RDM Corporation, 2012
All rights reserved. No part of this document may be reproduced in any form without the written consent of RDM Corporation.
Part Number: 302665
Revision: D
1
Contents
Compliance Statements ..................................................................2
Introduction .....................................................................................4
Requirements ..................................................................................5
Setting Up the EC6000i, EC7000i, or EC7500i ...............................6
Operating the Scanner ..................................................................15
Maintaining the EC6000i, EC7000i, or EC7500i ...........................20
Troubleshooting ............................................................................22
Specifications ................................................................................25
Warranty Information .....................................................................28
2
Compliance Statements
FCC Compliance Statement
NOTE for EC6000i , EC7000i, and EC7500i Series Scanners: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her
own expense.
Models with internal modem: This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the
bottom of this equipment is a label that contains, among other information, a product identifier in the format “US: AAAEQ##TXXX”. If
requested, this number must be provided to the telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68
rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. See installation instructions for details.
The Ringer Equivalence Number (or REN) is used to determine the number of devices that may be connected to a telephone line. Excessive
RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs
should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact
the local telephone company. For products approved after July 23, 2001, the REN for the product is part of the product identifier that has the
format “US: AAAEQ##TXXX”. The digits represented by ## are the REN without a decimal point (e.g. 03 is a REN of 0.3; 00 is a REN of 0.0).
For earlier products, the REN is separately shown on the label.
If this equipment causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of the
service may be required. But if advance notice isn’t practical the telephone company will notify the customer as soon as possible. Also, you will
be advised of your right to file a complaint with the FCC if you believe it is necessary.
3
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of this
equipment. If this happens the telephone company will provide advanced notice in order for you to make necessary modification to maintain
uninterrupted service.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation
commission for information.
If your home has specially wired alarm equipment connected to the telephone line ensure the installation of this scanner does not disable oyour
alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
CAUTION: Changes or modifications not expresssly approved by RDM Corporation could void the user’s authority to operate the
equipment.
All units covered by this manual have no user-serviceable parts inside. In the event repairs are ever needed to any RDM product, they should be
performed by RDM Corporation or an authorized representative of RDM Corporation. For information please contact RDM Corporation,
4-608 Weber Street North, Waterloo, Ontario, Canada N2V 1K4, at 1-800-567-6227, or RDM’s US service agent below.
US Service Agent
William Buser
(703) 286-5734
bbuser@rdmcorp.com
Industry Canada Compliance Statement
This product meets the applicable Industry Canada technical specifications/Le présent materiel est conforme aux specifications techniques
applicables d’Industrie Canada.
The Ringer Equivalence Number is an indication of the maximum number of devices allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices
does not exceed five/L’indice d’équivalence de la sonnerie (IES) sert à indiquer le nombre maximal de terminaux qui peuvent être raccordés à
une interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que
la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.
For information contact: RDM Corporation, 4-608 Weber Street North, Waterloo, Ontario, Canada N2V 1K4
4
Introduction
The EC6000i®, the EC7000i®, and the EC7500i®Series Scanners are cost effective, feature rich, imaging
solutions. Using RDM’s industry leading progressive MICR method and imaging technology, the EC6000i,
the EC7000i, and the EC7500i Series Scanners are ideal for Check Electronification, Check Cashing, and
Walk-in Bill Payment applications.
5
Requirements
• The EC6000i, the EC7000i, and the EC7500i units are for indoor use only. Keep the EC6000i, the
EC7000i, and the EC7500i dry; avoid areas of high humidity.
•Do not remove any cabinetry other than the areas specified in this guide. Removing cabinetry other
than the areas specified in this guide will void the warranty.
Recommendations
• This unit may be installed and programmed by a distributor (reseller) other than the original
manufacturer. Record all distributor contact information for future reference.
•Save the original box and packing material. Reuse them if the unit must be shipped to a new location.
•Position the unit so that the operator has easy access to the check path and a clear view of the LED. Do
not put the unit close to a heat source, in direct sunlight, or close to any device that can emit
electromagnetic interference, such as a computer monitor or power adapter.
6
Setting Up the EC6000i, EC7000i, or EC7500i
To set up the EC6000i, the EC7000i, and the EC7500i,
follow steps A – H.
A. Choose a Location
Locate your scanner in a place that:
• has a flat surface, such as a countertop or table
• is convenient for the scanner operator
• offers adequate ventilation and protection from
elements such as heat, dust, oil, or moisture
• is close to a telephone line or network connection
(depending on your unit) and power connections.
B. Unpack the Shipping Box
1. Open the top of the box.
2. Remove and unwrap the items.
3. Save the box and wrapping for future use.
NOTE: Before unpacking the box, examine
it for damage received during shipping. If
the scanner, or any component, appears
damaged, do not use it. File a claim with the
shipping company and contact your
distributor.
Your EC6000i, EC7000i, or EC7500i
product package includes the following:
• The EC6000i, the EC7000i, or the
EC7500i scanner
• Power adapter
• Telephone line (optional with modem) -
EC6000i or EC7000i only
• Franking Acknowledgement Printer
Cartridge (optional) -
Reorder P/N 6000-6050
• USB cable
7
C. Inspect the Unit’s Features
The illustrations below show a basic scanner (Model A), and an EC7500i scanner with a Magnetic Stripe
Reader (MSR) and printer (Model B). Scanner Model A will be graphically represented throughout this
manual for consistency. All other features of the EC6000i, the EC7000i, and the EC7500i are available as
standard or optional. All EC7500i series models are franker-enabled. Specific EC6000i and EC7000i series
models have franking capability.
Model A Model B
Check
Insertion
Slot
Printer
Scanner Status
LED
(Light)
Magnetic Stripe
Reader
Scanner Status
LED
(Light)
Check
Insertion
Slot
8
Inside Components
Cover Latch
Image Frame in raised position
Outside Cover in raised position
Image Sensor
Document Feed Plate comes out to reveal optional
Franking Acknowledgement Printer Assembly
(EC6000i shown)
Document Sensors
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere RDM Scanner Handbücher
