Record DFA 127 Einrichtungshandbuch

DFA 127 Basic quick set up

This Quick Guide is intended to be used in conjunction with a full installation

manual.

Once you have mechanically fitted your Swing unit follow this guide:

Fitting a pair? –Wire in the CAN Isolator before starting –(25 to 25, 26 to 26 etc..)

1. Using jumper J14 on the STG 127, one operator is set as Master and the other as

Slave. The operator of the active door leaf must always be selected as the Master

2. Select The rotation (Push or pull) on the Switch on the Control unit

A = PULL DIRECTION B = PUSH DIRECTION

3. Select English on the BDE

4. Press blue button for 6 flashes to select the spring type( the spring will go back and

forth –wait for it to stop) –On both operators if a pair

5. Press blue button for 4 flashes to enter programming mode - Master

6. Select configure system, then select Door type

7. Select either UK or UK LOW E depending on your risk assessment (on door safety or

not.

8. Put arm on with the door closed approx. 0 deg only finger tight

9. Press blue button for 3 flashes (–On both operators if a pair) and step back from the

door. The door should start to open slowly.

10.Stop the door-s at approx. 100 deg and the door will then close.

11.Select hold open on the BDED (top left)

12.Slacken the arm and close the door approx. 10 deg, tighten the arm finger tight. –

This Provides pre-tension on the springs.

13.Select manual operation on the BDED Top middle (snowflake) and the door will close.

14.Press the RECORD reset symbol until reset appears and then select reset. The door

will then evaluate the closed position and remember this as “Home”.

15.Tighten the arm (not overtight)

16.Press the blue button and the door should then open and close.

Now It Is time to set up Your Speeds & Basic Parameters

17.On the BDE Press then then

This will get you into the quick menu where you can adjust basic speeds

18.First Thing you will Notice is the Door open angle is not full.

Adjust the Open angle, open speed, close speed and Collision sensitivities according

to site conditions and BS 16005.

Fitting Activations

Wire your activation as per:

Test door in all operating Modes to confirm Activations

are working correctly

Fitting on Door Safety

1. If Fitting RC SWING Fast Install Sensors –PLUG & PLAY –See separate Quick Guide.

2. If Fitting others –Please refer to Diagram below :

If you are using Standard sensors –you need to turn the Test contacts on. (Aux Input –See

manual)

RECORD DFA 127 ABREVIATIONS

ABS - PULSE GENERATOR

AKA - EXTERNAL ACTIVATION

AKG - ACTIVATION COMMON CONTACT

AKI - INTERNAL ACTIVATION

AS - MASTER CIRCUIT

ASK - TERMINALS INSIDE THE HEADER

ATE - DRIVE UNIT

BDE-D - ELECTRONIC PROGRAMME SELECTOR

BDI - 3 POSITION ROCKER SWITCH

BDI-M –CIRCUIT BOARD FOR MECHANICAL PROGRAMME SELECTOR

BKL- PROCESSOR LED

CAN-H SERIAL DATA INTERFACE

CAN-L SERIAL DATA INTERFACE

CPU –MAIN MICRO PROCESSOR

DFA –AUTOMATIC SWING DOOR OPERATOR

EPROM - PROGRAMMABLE MEMORY CHIP

ES - CIRCUIT DIAGRAMME

FV - MANUFACTURING REGULATIONS

GTR - GEARING

HS - MAIN SWITCH 2 POLE

IKG - ENCODER

LED - LIGHT EMITTING DIODE

LD - LIGHT EMITTING DIODE

LS - CABLE PLAN

MF –MULTI FUNCTION SWITCH

MOT- MOTOR

MP - MAIN ASSEMBLY DIAGRAMME

NA - EMERGENCY STOP

NET - POWER SUPPLY UNIT

NS - MAIN POWER SWITCH

NSA - MAINS FAILURE

RAD - RADAR

SI - FUSE

SIO - OPENING FACE ON DOOR SAFETY –Written above Wiring Terminal

SIS - CLOSING FACE ON DOOR SAFETY –Written above Wiring Terminal

SSK - MORNING ENTRY KEY SWITCH

STG - CONTROL UNIT

STP - CONTROL UNIT PCB

TOE - DOOR LOCKING

TOW - DOOR OPENING WIDTH

TOZ - DOOR HOLD OPEN TIME

P - MICROPROCESSOR

VAK - LOCK CONTACT

VL - WIRING LIST

VMA - INSTRUCTIONS FOR WIRING AND ASSEMBLY

VVR –Electric Lock

Quick View of BDE Parameters

Guide to Blue Button – Multiple Use (MF)

No of Flashes

Level

Single Impulse –Opens Door

Tests the battery unit on STA16 & initialises the PHC for the first learn

Learns door parameters (Calibration Run)

Programming mode

tests the battery on STA 20

Spring Calibration run on the DFA 127 –Before connecting Arm

Not used

Factory standards reset

Full Reset -9 flash and then pull the emergency stop OUT then IN

Soft reset the same as the Record Logo

BDE – Control Switch

To both Lock and Unlock the Keypad operation:

Hold Open

Manual Operation

No Entry

2-Way Automatic

Locked / Closed

With this symbol

showing it represents

the key lock is ON

To reset the door:

Press and hold the Record logo for 10-13sec. The message “DFA127 Software Version “will flash up, followed by the

option to reset yes / No. Upon selecting Yes the doors will come to the closed position and reset. After 3sec

activate the doors to open so they may go through one learn cycle of open / close (moves slowly) and complete their

reset cycle.

BDI-M Set up

To Get the Door to lock on electric mags when the closed position is selected on the

Key switch you need to change the setting (In control panel Menu) to LOCK-A

Option 1 - MANUAL

Option 2 - LOCK-A

RED 24v Common

RED 24V Common

No Connection

AUTO

No Connection

LOCKED

Red / Green

MANUAL

Red / Green

AUTO

Red / Blue

HOLD

OPEN

Red / Blue

HOLD

OPEN

Terminal Connections on BDI-M

Red 3 - ......

AUTO

Red 3 - ......

LOCKED

Green 3 - 2

MANUAL

Green 3 - 2

AUTO

Blue 3 - 1

HOLD

OPEN

Blue 3 - 1

HOLD

OPEN

Reset Operator

Yes

For final exit of the building, place the program

selector into the locked function and when you are

ready to leave press the lock symbol once to give a

single open/close exit.

Once outside, stand clear of the sensors and after

the doors are closed, then set your manual locks.

Remember to unlock manual locks prior to using the

first entry key switch on the outside of the building.

ELECTRIC LOCK

Andere Handbücher für DFA 127

Inhaltsverzeichnis

Andere Record Türöffnungssystem Handbücher

Record

Record system 20 Reparaturanleitung

Record

Record R62 Bedienungsanleitung

Record

Record C 127 SU S Bedienungsanleitung

Record

Record system 20 RED Series Bedienungsanleitung

Record

Record K 32 M Bedienungsanleitung

Record

Record DFA 127 Bedienungsanleitung

Record

Record STA20 Bedienungsanleitung

Record

Record KEANE MONROE 2000 Series Bedienungsanleitung

Record

Record DFA 127 Bedienungsanleitung

Record

Record K32 ST Bedienungsanleitung

Record

Record PROTECT RC 2 Bedienungsanleitung

Record

Record 5100 Series Bedienungsanleitung

Record

Record 102-020.110.805 Betriebsanleitung

Record

Record C 127 SU H Bedienungsanleitung

Record

Record K21 Bedienungsanleitung

Record

Record 5100 Series Bedienungsanleitung

Record

Record DFA 70 Bedienungsanleitung

Record

Record FlipFlow TWIN Bedienungsanleitung

Record

Record K 32 Z Bedienungsanleitung

Record

Record BDE-D Bedienungsanleitung

Record

Record STM 20 RED/DUO Bedienungsanleitung

Record

Record C 127 SU OFFSET Bedienungsanleitung

Record

Record C 127 X SU H-B OFFSET Bedienungsanleitung

Record

Record HA8-SP Service-Handbuch

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Label

Label NEPTIS/LE Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Series Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Olide

Olide 120B Bedienungsanleitung

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung