Reiner P1-MP2-RD Bedienungsanleitung
GB
P1-MP2-RD
Operating Manual
7
1
Weld seam
2
Zip fastening
3
Clip
4
Print head
5
Clip arms
6
Print head nozzles
7
Print head contacts
AD
B
C
E
1
2
3
4
5
6
7
3
3
4
5
7
8
GB
For your safety
DANGER Warnings about risks where non-observance
of the measures may directly cause death or
serious injury.
WARNING Warnings about risks where non-observance
of the measures may cause death or serious
injury.
CAUTION Warnings about risks where non-observance of
the measures may cause injury.
PLEASE NOTE Warnings about risks where non-observance of
the measures may cause material damage.
Instructions and tips
Safety instructions for MP ink
WARNING
Special ink is highly flammable. Risk of burns!
„Store at 10 °C - 20 °C.
„Do not expose to direct sunlight.
WARNING
If in eyes.
„Rinse cautiously with water for several minutes.
„Remove contact lenses, if present and easy to do.
„Continue rinsing. Immediately call a POISON CENTER
or doctor/physician.
9
1. Making the print head ready for use
1.1. Opening the pack _Fig. A
The aluminium pouch has a resealable zip fastening
2
.
„With scissors, cut open the top of the pack between
the weld seam
1
and the zip fastening
2
.
„Unzip
2
the pack.
„Take out the print head
4
.
1.2. Releasing the clip _Fig. B+ C
The print head
4
is supplied with a reusable clip
3
.
„Place the print head
4
on a firm surface at an angle
of about 45° as shown in figure C.
„Hold the red clip
3
by the point with one hand.
„With the other hand, press the print head
4
down firmly. The
clip arms
5
will spring out and the print head
4
will slide
away from the clip
3
.
2. Printing material
For the best results, use material that is clean, non-greasy, dry
and at the same temperature as the print head.
Before carrying out a large print job, perform a test print.
10
GB
3. Storage _Fig. A+ D
MP ink is fast-drying. The time it takes the print head
nozzles
6
to dry up depends on the ambient temperature
and the humidity.
- If the printing break will probably take more than 5 minutes,
the print head
4
should be protected with the clip
3
.
- If the printing break will probably take more than 2 hours,
the print head
4
with the clip
3
should be stored in the
air-tight aluminium pouch.
„Remove the print head
4
out of the device.
„Place the print head
4
with the clip
3
on a smooth and solid
surface as shown in figure D.
„Press the print head
4
down until it snaps in the clip
3
.
„Place the print head
4
into the aluminium pouch and close
the zip fastening completely.
Use the print head within four weeks after opening.
11
4. Environmental Conditions
Temperature for storage 10°C to +20°C
Temperature for transport -20 °C to +40 °C (up to 24 hours)
5. Troubleshooting
Dried ink on the print head nozzles
6
may result in streaks
or reduced print quality.
5.1. Automatic cleaning
„Read the information about the cleaning of the print head
nozzles
6
in the manual for the electronic stamp.
5.2. Cleaning the print head nozzles manually
If the automatic cleaning of the nozzles
6
does not produce the
desired result, we recommend proceeding as follows:
„To remove dried ink, press a soft cloth, if necessary lightly
soaked in ethanol (spirits), against the print head nozzles
6
for about 3 seconds.
„Dab off the dissolved ink and wipe the nozzles dry.
12
GB
5.3. Reactivating the print head
If ink has dried inside the print head
4
it may be necessary
to reactivate it.
„Lay the print head down on a firm surface protected by
a lint-free cloth or piece of material.
„Place the syringe supplied firmly against the opening on top
of the print head
4
and carefully inject a small amount of air
(approx. 0.5 ml).
PLEASE NOTE
Risk of staining from discharged ink.
„Wipe up discharged ink with a lint-free cloth or piece of
material.
5.4. Cleaning the print head contacts
In rare cases, dirt on the print head contacts
7
may result in
inferior printing results.
„Clean the contacts on the print head
4
and in the device with
a soft cloth or cotton bud, if necessary lightly soaked
in ethanol (spirits).
Disposal
Directive 2002/96/EC (WEEE)
Electrical and electronic equipment and batteries
should not be disposed of along with domestic
or general waste. Dispose of equipment in an
environmentally friendly way.
37
Notes
Ernst Reiner GmbH & Co. KG
Baumannstr. 16
78120 Furtwangen
Phone +49(0)7723 657-0
Fax +49(0)7723 657-200
reiner@reiner.de
www.reiner.de
Award for
Operational
Excellence
|ZN-791061-001 F|02-2014
Danger
REINER MP2 RD
4 ml
Flammable liquid and vapour.
Causes serious eye damage.
H318H226
Acid Red 52Ethanol
Andere Handbücher für P1-MP2-RD
1
Inhaltsverzeichnis
Andere Reiner Drucker Handbücher
Reiner
Reiner speed-i-Jet 798 Bedienungsanleitung
Reiner
Reiner speed-i-Jet 798 Handbuch
Reiner
Reiner speed-i-Jet 798 Handbuch
Reiner
Reiner jetStamp 790 Handbuch
Reiner
Reiner jetStamp graphic 970 Bedienungsanleitung
Reiner
Reiner jetStamp 792 Bedienungsanleitung
Reiner
Reiner jetStamp 1025 Bedienungsanleitung
Reiner
Reiner 780 Bedienungsanleitung
Reiner
Reiner P3-MP Bedienungsanleitung
Reiner
Reiner speed-i-Jet 798 Bedienungsanleitung
Reiner
Reiner jetStamp 990 Bedienungsanleitung
Reiner
Reiner jetStamp 990 Bedienungsanleitung
Reiner
Reiner speed-i-Jet 798 Bedienungsanleitung
Reiner
Reiner speed-i-Marker 940 Bedienungsanleitung
Reiner
Reiner speed-i-Marker 940 Bedienungsanleitung
Reiner
Reiner speed-i-Jet 798 Bedienungsanleitung
Reiner
Reiner jetStamp graphic 970 Handbuch
Reiner
Reiner jetStamp 790 Bedienungsanleitung
Reiner
Reiner jetStamp 1025 Bedienungsanleitung
Reiner
Reiner speed-i-Marker 940 Bedienungsanleitung
