Reiner P3-MP Bedienungsanleitung

P3-MP

Instructions

Foil pouch

Print cartridge

Dust cover

Safety band

Latching wings

Rubber seal

Print nozzles

Printing contacts

For your safety

DANGER Warnings about risks where non-observance

of the measures may directly cause death or

serious injury.

WARNING Warnings about risks where non-observance

of the measures may cause death or serious

injury.

CAUTION Warnings about risks where non-observance of

the measures may cause injury.

PLEASE NOTE Warnings about risks where non-observance of

the measures may cause material damage.

Instructions and tips

Safety instructions for MP ink

WARNING

Special ink is highly flammable. Risk of burns!

„ Store at 10 ° C - 20 ° C.

„ Do not expose to direct sunlight.

WARNING

If in eyes.

„ Rinse cautiously with water for several minutes.

„ Remove contact lenses, if present and easy to do.

„ Continue rinsing. Immediately call a POISON CENTER

or doctor/physician.

1. Making the print head ready for use

1.1. Opening the pack _Fig. A

„ Cut open foil pouch

with shears.

„ Remove printing cartridge

1.2. Releasing the clip _Fig. B+ C

The print cartridge

is supplied with a reusable dust cover

„ Slightly push apart the latching wings

„ Remove safety band

„ Remove printing cartridge.

„ Use the printing cartridge according to the operating

instructions for the device.

2. Printing material

For the best results, use material that is clean, non-greasy, dry

and at the same temperature as the print head.

Polar or polarised surfaces are better suitable on plastics to be

printed on than surfaces with unpolar properties.

Before carrying out a large print job, perform a test print.

3. Storage _Fig. A+ B

MP ink is fast-drying. The time it takes the print nozzles

to dry up depends on the ambient temperature

and the humidity.

Put the device into the station during short print breaks or

close the nozzle cover.

Observe acoustic signals of the device.

Where the device is not equipped with a nozzle cover, protect

the printing cartridge

against drying out with the dust

cover

when interrupting work.

To securely close the nozzles

of the printing cartridge

keep the seal at the dust cover

free from dirt and dust.

„ Remove the printing cartridge

out of the device.

„ Guide the printing cartridge into the dust cover

„ Push the printing cartridge down until the

latching wings

click.

„ Fasten the latching wings with the safety band

Use the print head within four weeks after opening.

4. Environmental Conditions

Temperature for storage +10° C to +20° C

Temperature for transport -20 ° C to +40 ° C (up to 24

hours)

5. Troubleshooting _Fig. D

Dried ink on the print nozzles may result in streaks or reduced

print quality.

5.1. Cleaning mechanism

„ Observe notes on cleaning of the print nozzles

in the

operating instructions for the device.

5.2. Cleaning the print head nozzles manually

We recommend the following measure if the cleaning mechanism

does not lead to the desired success:

„ To remove dried ink, press a soft cloth, if necessary lightly

soaked in ethanol (spirits), against the print nozzles

for about 3 seconds.

„ Dab off the dissolved ink and wipe the print nozzles dry.

5.3. Cleaning the print head contacts

In rare cases, dirt on the print head contacts may result in inferior

printing results.

„ Clean the contacts

on the print head

and in the device

with a soft cloth or cotton bud, if necessary lightly soaked

in ethanol (spirits).

Disposal

Directive 2002/96/EC (WEEE)

Old devices must not be disposed of in the common

household waste but in a specified acceptance point

for recycling of electrical and electronic devices.

Notes

Award for

Operational

Excellence

Ernst Reiner GmbH & Co. KG

Baumannstr. 16

78120 Furtwangen

Phone +49 7723 657-0

Fax +49 7723 657-200

reiner@reiner.de

|PC-947101-100-1-E|11-2013

Andere Handbücher für P3-MP

Inhaltsverzeichnis

Andere Reiner Drucker Handbücher

Reiner

Reiner jetStamp 1025 Bedienungsanleitung

Reiner

Reiner P1-MP2-RD Bedienungsanleitung

Reiner

Reiner jetStamp 990 Bedienungsanleitung

Reiner

Reiner jetStamp graphic 970 Bedienungsanleitung

Reiner

Reiner speed-i-Marker 940 Bedienungsanleitung

Reiner

Reiner jetStamp 1025 Bedienungsanleitung

Reiner

Reiner 780 Bedienungsanleitung

Reiner

Reiner speed-i-Jet 798 Bedienungsanleitung

Reiner

Reiner jetStamp 790 Bedienungsanleitung

Reiner

Reiner jetStamp 790 Handbuch

Reiner

Reiner speed-i-Marker 940 Bedienungsanleitung

Reiner

Reiner jetStamp graphic 970 Handbuch

Reiner

Reiner speed-i-Jet 798 Handbuch

Reiner

Reiner speed-i-Jet 798 Bedienungsanleitung

Reiner

Reiner speed-i-Jet 798 Handbuch

Reiner

Reiner speed-i-Jet 798 Bedienungsanleitung

Reiner

Reiner jetStamp 792 Bedienungsanleitung

Reiner

Reiner speed-i-Marker 940 Bedienungsanleitung

Reiner

Reiner jetStamp 990 Bedienungsanleitung

Reiner

Reiner speed-i-Jet 798 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung