Reliable F1-42 Series Handbuch
F1-42 Series Sprinklers Summary
Sprinkler
Model
K-Factor gpm/psi1/2
(lpm/bar1/2)Orientation Listings & Approvals Max. Working Pressure
psi (bar)
Sprinkler
Identication
Number (SIN)
F1-42 4.2 (60)
Upright
cULus
175 (12) RA1323
Pendent 175 (12) RA1313
Table A
Model F1-42 Pendent
Model F1-42 Upright
Features
• Standard coverage standard-response sprinklers
• Upright and pendent deflectors
• Low prole, compact design
• Available in a wide variety of nishes
Product Description
Reliable Model F1 series sprinklers are standard-response
standard spray automatic re sprinklers utilizing a 5.0 mm glass
bulb thermal element.
Pendent and horizontal sidewall sprinklers may be installed
exposed or surface mounted using escutcheons such as the
Reliable Models B, C, or HB (reference Technical Bulletin 204).
When installed recessed, the Model F1-42 series sprinklers
are specically listed with and may only be installed with listed
Reliable escutcheons. Refer to the technical information on the
following pages for specic listings for recessed installations and
refer to Figure 3 for dimensional information.
When tted with an approved water shield, these sprinklers may
considered intermediate sprinklers for use in racks, below grated
walkways, and other areas where intermediate level sprinklers are
required.
Table A provides a summary of the approvals and availability of
specic Model F1-42 series sprinkler congurations. Additional
technical information for each sprinkler model is provided on the
following pages.
Note: This bulletin may contain information on New and Legacy
sprinklers that reflects a dimensional change only. Sprinkler
Identication Number (SIN), application, performance, and
listings/approval are not otherwise affected. Sprinklers with new
frames can be identied by a rotoclip indent on one side of the
wrench boss and in some cases an installed rotoclip. Sprinklers
with new frames will include the sufx “N” in the order. For
reference only, legacy version of this sprinkler can be found on
Technical Bulletin 014.
www.reliablesprinkler.com
K-factor 4.2 (60)
F1-42 Series
Standard-Response Sprinklers
Bulletin 067 April 2021
Model F1-42 Upright Sprinkler SIN RA1323
Technical Specications
Style: Upright
Threads: 1/2” NPT or ISO 7-R1/2
Nominal K-Factor: 4.2 (60)
Max. Working Pressure: 175 psi (12 bar)
Material Specications
Thermal Sensor: 5.0mm Glass Bulb
Sprinkler Frame: Brass Alloy
Cap: Bronze Alloy
Sealing Washer: Nickel with PTFE
Load Screw: Copper Alloy
Deflector: Brass Alloy
Sprinkler Finishes
(See Table B)
Sensitivity
Standard Response
Temperature Ratings
135°F (57°C)
155°F (68°C)
175°F (79°C)
200°F (93°C)
286°F (141°C)*
360°F (182°C)
500°F (260°C)
Guards & Shields (New Frames)
F-1 Guard Kit
F-3 Guard/Shield Kit
Guards & Shields (Legacy Frames)
D-1 Guard
Sprinkler Wrenches
Model W2
Model J (New frame with guard installed)
Model JD (Legacy frame with guard
installed)
Listings and Approvals
cULus
Model F1-42 Upright Sprinkler Components and Dimensions Figure 1
Bulletin 067
April 2021
Page 2 of 6
www.reliablesprinkler.com
Model F1-42 Pendent Sprinkler SIN RA1313
Technical Specications
Style:
Pendent
Recessed Pendent
Threads: 3/4” NPT or ISO 7-R3/4
Nominal K-Factor: 4.2 (60)
Max. Working Pressure: 175 psi (12 bar)
Material Specications
Thermal Sensor: 5.0mm Glass Bulb
Sprinkler Frame: Brass Alloy
Cap: Bronze Alloy
Sealing Washer: Nickel with PTFE
Load Screw: Copper Alloy
Deflector: Brass Alloy
Sprinkler Finishes
(See Table B)
Sensitivity
Standard Response
Temperature Ratings(1)
135°F (57°C)
155°F (68°C)
175°F (79°C)
200°F (93°C)
286°F (141°C)
360°F (182°C)
500°F (260°C)
Recessed Escutcheons
Model F1
Model F2
Model FP
Guards & Shields (New Frames)(2)
F-7 Guard Kit
F-8 Guard/Shield Kit
Guards & Shields (Legacy Frames)(2)
D-1 Guard
Sprinkler Wrenches
Model W2 (pendent)
Model W4 (recessed)
Model J (New frame with guard installed)
Model JD (Legacy frame with guard
installed)
Listings and Approvals
cULus
Notes:
1. 286°F (141°C) and higher temperature rated sprinklers not listed for recessed use.
2. Not suitable for recessed pendent installations.
Model F1-42 Pendent Sprinkler Components and Dimensions Figure 2
Bulletin 067
April 2021
Page 3 of 6
www.reliablesprinkler.com
Note: Please refer to Figure 3 for recessed installation.
Recessed Installation: Pendent Sprinklers Figure 3
FP Escutcheon
F1 Escutcheon
(F2 similar)
Bulletin 067
April 2021
Page 4 of 6
www.reliablesprinkler.com
Installation
Model F1 Series sprinklers must be installed in accordance with
NFPA13 and the requirements of all applicable authorities having
jurisdiction. Model F1 Series sprinklers must be installed with the
Reliable sprinkler installation wrench identied in this Bulletin. Any
other wrench may damage the sprinkler. A leak tight sprinkler joint
can be obtained with a torque of 8 to 18 lb-ft (11 to 24 N-m). Do
not tighten sprinklers over the maximum recommended installation
torque. Exceeding the maximum recommended installation torque
may cause leakage or impairment of the sprinkler.
Glass bulb sprinklers have orange bulb protectors or protective
caps to minimize bulb damage during shipping, handling and
installation. Reliable sprinkler installation wrenches are designed
to install sprinklers with bulb protectors in place. Remove the bulb
protector at the time when the sprinkler system is placed in service
for re protection. Removal of the bulb protector before this time
may leave the bulb vulnerable to damage. Remove bulb protectors
by undoing the clasp by hand. Do not use tools to remove bulb
protectors.
Standard Finishes Special Application Finishes
Sprinkler F1, F2 and FP(3)
Escutcheons Sprinkler F1, F2 and FP(3)
Escutcheons
Bronze Brass Electroless Nickel PTFE(4) Bright Brass
Chrome Plated Chrome Plated Bright Brass(5) Black Plated
White Polyester(4) White Polyester Black Plated Black Paint
Black Paint Off White
Off White Chrome Dull
Chrome Dull
Notes:
1. Other nishes and colors are available on special order. Consult your Reliable sales representative for details.
2. Paint or any other coating applied over the factory nish will void all approvals and warranties.
3. The Model FP assembly consists of a sprinkler mounted in a galvanized steel cup with a nished trim ring or cover plate.
4. cULus Listed as corrosion resistant.
5. For 200°F (93°C) maximum temperature rated sprinklers only.
Finishes(1)(2) Table B
Wrenches
Model W2 (upright, pendent) Model W4 (recessed pendent)
Model J (New frame with guard installed)
Maintenance
Reliable Model F1 series sprinklers should be inspected and the
sprinkler system maintained in accordance with NFPA 25, as well
as the requirements of any Authorities Having Jurisdiction.
Prior to installation, sprinklers should remain in the original
cartons and packaging until used. This will minimize the potential
for damage to sprinklers that could cause improper operation or
non-operation.
Do not clean sprinklers with soap and water, ammonia liquid or
any other cleaning fluids. Remove dust by gentle vacuuming
without touching the sprinkler.
Replace any sprinkler which has been painted (other than factory
applied). A stock of spare sprinklers should be maintained to
allow quick replacement of damaged or operated sprinklers.
Failure to properly maintain sprinklers may result in inadvertent
operation or non-operation during a re event.
Model JD (Legacy frame with guard installed)
Bulletin 067
April 2021
Page 5 of 6
www.reliablesprinkler.com
Bulletin 067
April 2021
Page 6 of 6
www.reliablesprinkler.com
Guarantee
For the guarantee, terms, and conditions, visit www.
reliablesprinkler.com.
Ordering Information
Specify the following when ordering:
Model
• F1-42
Deflector/Orientation
• Upright
• Pendent
• Pendent - FP
Temperature Rating
• See sprinkler technical specications
Sprinkler Finish
• See Table B
Recessed Escutcheon*
• F1
• F2
• FP
Escutcheon Finish
• See Table B
Sprinkler Wrench
• Model W2 (upright and pendent)
• Model W4 (recessed)
• Model J (New frame with guard installed)
• Model JD (Legacy frame with guard installed)
*Note: 286°F (141°C) and higher temperature rated sprinklers
are not listed to be used recessed.
P/N 9999970619
Dieses Handbuch passt für folgende Modelle
9
Inhaltsverzeichnis
Andere Reliable Bewässerungssystem Handbücher
Reliable
Reliable F1FR QREC Handbuch
Reliable
Reliable RFC30 Bedienungsanleitung
Reliable
Reliable F3-80 Series Handbuch
Reliable
Reliable F1FR80VdS Series Handbuch
Reliable
Reliable N25 ESFR Bedienungsanleitung
Reliable
Reliable G6-80 K8.0 Bedienungsanleitung
Reliable
Reliable RFC56 Bedienungsanleitung
Reliable
Reliable DH56 Dry Bedienungsanleitung
Reliable
Reliable RFC Series Handbuch
Reliable
Reliable G4 Bedienungsanleitung
Reliable
Reliable G5-56 Dry Bedienungsanleitung
Reliable
Reliable F156 EC Series Bedienungsanleitung
Reliable
Reliable G5-56 Dry Bedienungsanleitung
Reliable
Reliable F3-56 Series Bedienungsanleitung
Reliable
Reliable RFC43 Bedienungsanleitung
Reliable
Reliable LT56 Series Bedienungsanleitung
Reliable
Reliable N252 EC Pendent Bedienungsanleitung
Reliable
Reliable GFR Bedienungsanleitung
Reliable
Reliable F1FR56 Bedienungsanleitung
Reliable
Reliable F156 Series Bedienungsanleitung
Beliebte Bewässerungssystem Handbücher anderer Marken
Hunter
Hunter Institutional Series Bedienungsanleitung
Cellfast
Cellfast 52-305 Bedienungsanleitung
Tyco Fire Product
Tyco Fire Product Star Galaxy SGQR Bedienungsanleitung
Tyco Fire Product
Tyco Fire Product CENTRAL A Bedienungsanleitung
Oral Care Technologies
Oral Care Technologies Hydro Floss Bedienungsanleitung
Tyco Fire Product
Tyco Fire Product Gem F892 Bedienungsanleitung
Toro
Toro 730 Series Kurzanleitung
Eden
Eden 97063-EDAMZ Bedienungsanleitung
Tyco
Tyco TY-L Series Bedienungsanleitung
Tyco Fire Product
Tyco Fire Product CENTRAL ELO-231 Bedienungsanleitung
Johnson Controls
Johnson Controls tyco ESFR-17 Bedienungsanleitung
Victaulic
Victaulic VicFlex I-VICFLEX.AQC-U Bedienungsanleitung