Remington G2 Graphite Series Bedienungsanleitung

G2 GRAPHITE SERIES

MULTI GROOM KIT

3 YEAR WARRANTY PG2000AU

To register your product go to

www.remington-products.com.au

www.remington.co.nz

USE & CARE

MANUAL

PLEASE READ

PRIOR TO USE

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic precautions should

always be observed, including the following.

READ ALL INSTRUCTIONS BEFORE USING

DANGER: As with most electrical appliances, electrical parts are

electrically live even when the switch is off.

For additional protection, the installation of a residual current

device (rcd) having a rated residual operating current not

exceeding 30 mA is advisable in the electrical circuit supplying

the bathroom. Ask your installer for advice.

KEEP AWAY FROM WATER

WARNING: TO REDUCE THE RISK OF BURNS, ELECTROCUTION AND

FIRE OR INJURY TO PERSONS

• Do not place or store the appliance or charging adaptor where it can

fall or be knocked into a sink or bath.

• Do not place in or drop into water or any other liquid.

• If an appliance falls into water, “unplug it” immediately. Do not reach

into the water.

• Unplug the charging adaptor from the electrical outlet immediately after

fully charging.

• Do not use while bathing or in the shower.

• Unplug and switch off this appliance before cleaning it.

• Use this appliance only for its intended use as described in this

manual.

• Do not use attachments not recommended by Remington.

• Never drop or insert any object into any opening of this appliance.

• Keep the cord away from heated surfaces.

• Do not use this appliance with a damaged or broken trimming

attachments as injury may occur.

• Always store the charging adaptor in a moisture-free location.

• For household use only.

• This appliance should not be used by children or other persons with

reduced physical, sensory or mental capabilities or lack of experience

and knowledge unless they have been given supervision or instruction

concerning use of the appliance in a safe way and understand the

hazards involved.

• This appliance is not a toy. Children shall be supervised to ensure they

do not play with the appliance. Cleaning, use, and maintenance shall

not be made by children without supervision.

• Keep the appliance and the power cord away from edge of tables or

countertops and out of reach of children and persons with reduced

physical, sensory or mental capabilities.

• Do not use on people who are asleep.

• Never operate this appliance if it has a damaged cord or plug, if it is

not working correctly, if the charging adaptor has been damaged or

dropped into water.

• Do not use an extension cord or a voltage converter with this

appliance.

• Do not wrap the cord around the appliance.

• WARNING: For recharging the battery, only use the adaptor supplied

with the appliance.

• Always replace the adaptor with one of the original type.

WARNING - KEEP THE APPLIANCE DRY

SAVE THESE INSTRUCTIONS

PG2000AU G2 GRAPHITE SERIES MULTI GROOM KIT

USE & CARE INSTRUCTION MANUAL

Thank you for purchasing your Remington®G2 Graphite Series Multi-

Grooming Kit. Inside this manual you will find tips on using and caring for

your groomer.

KEY PARTS

1. 30mm Trimmer Head

2. Groomer Handle

3. On/Off Switch

4. Charging Indicator Light

5. 1.5mm & 3mm Fixed Comb

6. Nose, Ear, Eyebrow Trimmer

Head

7. Adjustable Comb

Attachment (2-20mm)

Also Includes:

• Power Adaptor

• Pouch

Note: The Adjustable Comb Attachment has various length settings. When

first becoming familiar with your groomer, begin with a higher numbered

setting. Adjust cutting length, as desired.

ABOUT YOUR GROOMER

PG2000AU SPECIFICATIONS

Power System Cordless (Rechargeable)

Full Charge Time 16 Hours

Run Time 40 Minutes

Indicators LED

Voltage Type Worldwide

Voltage Type: Worldwide Voltage - groomer automatically adapts to and

outlet voltage between 100V and 240V.

Note: Some countries will require the use of a plug adaptor that is not

included with your groomer.

CHARGING

Before using your trimmer for the first time, charge for 16 hours.

1. Ensure the product is switched off.

2. Connect the charging adaptor to the product and then to the mains.

• When charging, the charge indicator light will light up.

• Your trimmer cannot be overcharged. However, if it is not going to be

used for an extended period of time (2-3 months), unplug it from the

mains and store.

• To preserve the life of your batteries, let them run out every 6 months

then recharge for 16 hours.

• On a full charge, your beard trimmer will run for up to 40 minutes of

cordless usage.

ATTACHING AND REMOVING THE GROOMING HEADS

• Ensure that the groomer is switched off before fitting or removing

heads.

• To remove, rotate the head anti-clockwise until it unlocks and then lift

off.

• To fit, place the desired head on top of the groomer and rotate head

clockwise to lock into place.

ATTACHING AND REMOVING ADJUSTABLE COMB ATTACHMENT

• The Adjustable Comb attachment has 10 Length settings: 2-20mm

(in increments of 2mm). Begin with a higher numbered setting. Adjust

cutting length as desired once you are familiar with using the groomer,

it is better to select a longer hair length setting in order not to trim too

much hair.

• To fit, line up the rails on the comb with the slots on the sides of the

groomer and slide the comb downwards onto the groomer.

• To adjust, press and hold the adjustment button on the back of the

comb and slide the comb up or down. Release the button to lock the

comb at that position. The length of cut is indicated by the scale on the

side of the groomer.

• To remove, press and hold the adjustment button and push the comb

up and off the groomer.

ATTACHING AND REMOVING FIXED COMBS

• To fit, hook the front of the fixed comb over the teeth of the 30mm

trimmer head.

• Press the back of the fixed comb down until it clicks into place.

• To remove, lift the tab on the back of the fixed comb upwards until it

comes free from the 30mm trimmer head.

GROOMING TIPS

Hair Clipping: 30mm Trimmer Head With Adjustable Comb (2-20mm)

• Hair should be dry and free of lotions or other liquids.

• Comb outward to obtain maximum height / length and facing in the

same direction.

Step 1: Nape of the neck

1. Using a hand-held mirror is necessary if self-trimming.

2. Fit the 30mm trimmer head and adjustable comb.

3. Set the adjustable comb to 4 mm or 6 mm.

4. Hold the groomer with the blade teeth pointing upwards. Begin

starting at the centre of the head at the base of the neck.

5. Slowly lift the groomer, working upwards and outwards through the

hair, trimming just a little at a time.

Step 2: Back of the head

• With the adjustable comb set at 12 mm or 18 mm, cut the hair at the

back of the head.

Step 3: Side of the head

1. Adjust the comb to a shorter length setting for the areas around the

ears.

2. Increase the length setting on the adjustable comb to gradually

transition the length of hair on the side of the head to the longer hair

on the top of the head.

Step 4: Top of the head

1. Adjust the comb to the longer length settings (up to 20 mm) then cut

the hair on top of the head against the direction in which the hair

normally grows.

2. Always work from the back of the head.

Trim the sideburns

• To trim sideburns, adjust the comb to the desired length setting, or use

one of the clips on comb.

3-Day Stubble, and Body Hair Maintenance; 30mm Trimmer Head With

1.5mm or 3mm Fixed Comb

Let your stubble grow to a length that is slightly longer than the look you

are trying to achieve.

1. Fit the 1.5 mm fixed comb to the wide trimmer attachment.

2. Run your trimmer through your beard against the direction of hair

growth.

• For more control over the length of your stubble, you can use the

adjustable comb and trim your stubble down in increments starting at

a longer length setting until you get the desired look.

Beard / Moustache: 30mm Trimmer Head With Adjustable Comb

(2-20mm)

1. Use a small comb to straighten hairs for trimming.

2. Fit the 30mm trimmer head and adjustable comb.

3. Set the adjustable comb to the desired length.

4. Start trimming under the chin following the line of the jaw.

5. Work upwards towards the ear and upper beard line.

Contour Edging: 30mm Trimmer Head

1. Hold the groomer with the cutting blade (teeth) facing you and at 90

degrees to the skin.

2. Start with the edge of the beard/moustache line and, with the blade

resting lightly against the skin, use slow controlled movements to

create contoured lines.

Close Hair Cutting: 30mm Trimmer Head

1. Use the fingers of one hand to lift the hair at the base of your head up

off your neck.

2. Your index finger should be covering the roots of the hairs you are

lifting to prevent them from being accidentally cut.

3. Hold the groomer to the base of your neck with the blade facing up.

Move the groomer up the neck until it touches your index finger which

is protecting the hair roots.

4. Move your groomer slowly and keep the hair roots at the base of your

head out of the way of the groomer.

Ears: Nose, Ear, Eyebrow Trimmer Head

1. Fit the nose, ear, eyebrow trimmer head onto the groomer handle.

2. When trimming inner ears, avoid inserting the groomer more than

6mm into ear canal.

3. Turn the groomer on.

4. Insert the groomer’s cutting unit gently into the ear canal.

5. Rotate the groomer in a circular motion while gently moving in and out

of ear canal.

Eyebrows: Nose, Ear, Eyebrow Trimmer Head

1. Carefully guide the head to remove any stray or longer hairs from the

eyebrow.

2. For best results, do not use the groomer to define entire eyebrow.

Nose: Nose, Ear, Eyebrow Trimmer Head

1. Turn the groomer on.

2. Carefully insert the groomer’s cutting unit no more than 6mm into

nostril.

3. Rotate the groomer in a circular motion while gently moving in and out

of nose.

CLEANING, CARE & MAINTENANCE

Note: Always clean the groomer heads and attachment immediately after

use to ensure maximum performance and a proper operating life.

Clean Combs and Trimmer Heads With a Soft Brush (not included)

• With the head removed from the handle, gently brush out hair clippings

from the cutting system and top of groomer handle.

Clean Heads With Water

• With the head removed from the handle, rinse ONLY under warm

running water. Do NOT use hot water as this might cause damage.

Note: The groomer handle should not be rinsed.

This product is not suitable for bath or shower.

This product conforms to radio frequency interference requirements

Any product purchased and used commercially carries a limited 90 Day Warranty.

Oiling Blades & Cautions

• Rinsing attachments under water will require a re-lubrication of the

cutting blades once per month. Using only light grade oils (e.g. sewing

machine oil), simply place one or two drops lightly over cutters with

fingertip. Wipe away all excess

Note: Do not lubricate the foil shaver with oil as it is permanently lubricated.

BATTERY DISPOSAL

Note: The battery is not intended to be removed or replaced under normal

use.

• The PG2000AU contains a nickel metal hydride battery. Once the

trimmer has reached the end of its life, to ensure proper disposal of

the product, please take the appliance to a recycling centre, where the

internal rechargeable battery should be removed by a professional and

recycled separately.

• For more information about recycling of electrical and battery operated

appliances, please contact your local council office or your household

waste disposal service.

Caution: Do not put in the fire or mutilate your batteries when disposing as

they may burst and release toxic materials. Do not short circuit as it may

cause burns.

We suggest you use local waste management centres to recycle this

product at end of life.

Andere Handbücher für G2 Graphite Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Remington Pflegeset Handbücher

Remington

Remington PG6135 Bedienungsanleitung

Remington

Remington Smooth & Silky WPG-4050 Bedienungsanleitung

Remington

Remington Trim & Shape WPG4021AU Bedienungsanleitung

Remington

Remington PG6060 Bedienungsanleitung

Remington

Remington Smooth & Silky WPG2000 Bedienungsanleitung

Remington

Remington WETech PG6250 Bedienungsanleitung

Remington

Remington PG6030 Bedienungsanleitung

Remington

Remington Omniblade Face & Body Bedienungsanleitung

Remington

Remington Titanium PG-350 Bedienungsanleitung

Remington

Remington PG6125 Bedienungsanleitung

Remington

Remington PG025AU Bedienungsanleitung

Remington

Remington Titanium PG-350 Bedienungsanleitung

Remington

Remington HC9000 Bedienungsanleitung

Remington

Remington Trim & Shape WPG-150 Bedienungsanleitung

Remington

Remington Vacuum 5 in 1 Grooming Kit PG6070 Bedienungsanleitung

Remington

Remington MB4200 Bedienungsanleitung

Remington

Remington PG-525 Bedienungsanleitung

Remington

Remington MB4200 Bedienungsanleitung

Remington

Remington Groom Kit Plus PG6150 Bedienungsanleitung

Remington

Remington NE8000 Bedienungsanleitung

Remington

Remington PG6130 Bedienungsanleitung

Remington

Remington QuickGroom BHT6450 Bedienungsanleitung

Remington

Remington Nano Groom Essentials Series Bedienungsanleitung

Remington

Remington PG6025 Bedienungsanleitung

Beliebte Pflegeset Handbücher anderer Marken

Conair

Conair STUBBLE TRIM GMT265CSC Bedienungsanleitung

Philips

Philips Norelco G370/65 Bedienungsanleitung

Wahl

Wahl 9854L 9860L, 9876L Bedienungsanleitung

Zoofari

Zoofari ZTPS 6 C1 Produktinformationsblatt

Philips

Philips QG3270/32 Betriebsanleitung

HOFFEN

HOFFEN SHR-H024 Bedienungsanleitung

BaByliss for MEN

BaByliss for MEN G890E Bedienungsanleitung

Sinbo

Sinbo SHC 4348 Bedienungsanleitung

Philips

Philips QG3050/20 Bedienungsanleitung

BARB'XPERT

BARB'XPERT FPH-005 Bedienungsanleitung

anko

anko RFC-568 Bedienungsanleitung

Philips

Philips QG3280/41 Betriebsanleitung

Arzum

Arzum TRACE AR5200 Bedienungsanleitung

Philips

Philips QG3260/41 Betriebsanleitung

HICOZY

HICOZY HS-CW01-B Bedienungsanleitung

Philips

Philips Multigroom series 5000 QG3347/15 Bedienungsanleitung

decakila

decakila KMHR016W Bedienungsanleitung

Memorism

Memorism GS5 Bedienungsanleitung