Remote Control MARANTEC D343 Betriebsanleitung

http://www.remotecontrol-

express.com

Connection of the receiver to the motor:

1. Unplug your motor.

Check that your receiver is supplied with a 12 or 24 power

by the circuit board of your motor is greater (for example, 220 ), you will have to install a

transformer.

Make the following connections with the electric

-Connect channel 1

betwee

the hole under the screws and then screw them to lock the wire).

Connect channel 2 between terminals 7 and 8 on the receiver

connection of this channel is not displa

Connect the terminal + of the motor (or terminal with a tension indication) to terminal 5 on

the receiver.

-Connect the terminal –

or GMD of the motor to

Your receiver is connected.

Receiver already in use and to be kept

(example of configuration)

Main receiver card

Programming Manual

express.com

- TEL : 44 (0) 207 399 7782 - FAX :

44 (0) 207 927 3151

MARANTEC D343 – D344

Connection of the receiver to the motor:

Check that your receiver is supplied with a 12 or 24 power

supply.

If the voltage delivered

by the circuit board of your motor is greater (for example, 220 ), you will have to install a

Make the following connections with the electric

al wires as

indicated in the diagram above

betwee

n terminals 2 and 3 on the receiver

(you have to insert the wire in

the hole under the screws and then screw them to lock the wire).

Connect channel 2 between terminals 7 and 8 on the receiver

(

for more clarity, the

connection of this channel is not displa

yed in the diagram above).

Connect the terminal + of the motor (or terminal with a tension indication) to terminal 5 on

or GMD of the motor to

terminal 4

on the receiver

Your receiver is connected.

Receiver already in use and to be kept

(example of configuration)

Main receiver card

44 (0) 207 927 3151

If the voltage delivered

by the circuit board of your motor is greater (for example, 220 ), you will have to install a

indicated in the diagram above

(you have to insert the wire in

for more clarity, the

Connect the terminal + of the motor (or terminal with a tension indication) to terminal 5 on

on the receiver

http://www.remotecontrol-

express.com

Programming of the

first remote control with

Open the casing of your receiver.

On the receiver circuit board, press the button

Press a button on your new remote control. Keep it pressed down. The LED light L1

illuminates fixedly. Let the button on your new remote control go.

4. Wait 10 seconds.

Your new remote control is programmed.

Programming of the following remotes:

Connect the old and the new remote control with the supplied broach (diagram above).

2. Press a

button on your old (or already

The LED light on your old remote control illuminates.

While keeping the button on your already

the button you wish to program on

light on

your new remote control blinks and then illuminates fixedly. Let the buttons go.

Repeat this procedure for each button you wish to program.

5. Wait 10 seconds.

Your new remote control is programm

Programming Manual

express.com

- TEL : 44 (0) 207 399 7782 - FAX :

44 (0) 207 927 3151

first remote control with

the receiver:

Open the casing of your receiver.

On the receiver circuit board, press the button

CH1

. Let it go. The LED light L1 blinks.

Press a button on your new remote control. Keep it pressed down. The LED light L1

illuminates fixedly. Let the button on your new remote control go.

Your new remote control is programmed.

Programming of the following remotes:

Connect the old and the new remote control with the supplied broach (diagram above).

button on your old (or already

programmed) remote control. Keep it pressed down.

The LED light on your old remote control illuminates.

While keeping the button on your already

-programmed remote control

the button you wish to program on

your new remote control. Keep i

t pressed down. The LED

your new remote control blinks and then illuminates fixedly. Let the buttons go.

Repeat this procedure for each button you wish to program.

Your new remote control is programm

ed.

44 (0) 207 927 3151

. Let it go. The LED light L1 blinks.

Press a button on your new remote control. Keep it pressed down. The LED light L1

Connect the old and the new remote control with the supplied broach (diagram above).

programmed) remote control. Keep it pressed down.

pressed down, press

t pressed down. The LED

your new remote control blinks and then illuminates fixedly. Let the buttons go.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Remote Control Empfänger Handbücher

Remote Control

Remote Control RCS433-BR2 Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung