Renesas FP-144 Bedienungsanleitung
H8S/2643 Series
FP-144
User System Interface Cable
(HS2643ECH61H)
for E6000 Emulator
User’s Manual
HS2643ECH61HE(C)
Cautions
1. Renesas neither warrants nor grants licenses of any rights of Renesas’s or any third party’s
patent, copyright, trademark, or other intellectual property rights for information contained in
this document. Renesas bears no responsibility for problems that may arise with third party’s
rights, including intellectual propertyrights, in connection with use of the information contained
in this document.
2. Products and product specifications may be subject to change without notice. Confirm that you
have received the latest product standards or specifications before final design, purchase or use.
3. Renesas makes every attempt to ensure that its products are of high quality and reliability.
However, contact Renesas’s sales office before using the product in an application that demands
especially high quality and reliability or where its failure or malfunction may directly threaten
human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power,
combustion control, transportation, traffic, safety equipment or medical equipment for life
support.
4. Design your application so that the product is used within the ranges guaranteed by Renesas
particularly for maximum rating, operating supply voltage range, heat radiation characteristics,
installation conditions and other characteristics. Renesas bears no responsibility for failure or
damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider
normally foreseeable failure rates or failure modes in semiconductor devices and employ
systemic measures such as fail-safes, so that the equipment incorporating Renesas product does
not cause bodily injury, fire or other consequential damage due to operation of the Renesas
product.
5. This product is not designed to be radiation resistant.
6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document
without written approval from Renesas.
7. Contact Renesas’s sales office for any questions regarding this document or Renesas
semiconductor products.
i
Preface
Thank you for purchasing this user system interface cable (HS2643ECH61H) for the Renesas’s
original microcomputer H8S/2643 series.
The HS2643ECH61H is a user system interface cable that connects an H8S/2633 series E6000
emulator (HS2633EPI61H; hereinafter referred to as the emulator) to the IC socket for a FP-144
package for the H8S/2643 series MCU on the user system.
ii
Contents
Section 1 Configuration....................................................................................1
Section 2 Connection Procedures......................................................................3
2.1 Connecting User System Interface Cable to Emulator Station .........................................3
2.2 Connecting User System Interface Cable to User System................................................5
2.2.1 Installing IC Socket .............................................................................................5
2.2.2 Soldering IC Socket.............................................................................................6
2.2.3 Inserting Cable Head ...........................................................................................6
2.2.4 Fastening Cable Head..........................................................................................7
2.2.5 Fastening Cable Body..........................................................................................9
2.3 Recommended Dimensions for User System Mount Pad.................................................10
2.4 Dimensions for User System Interface Cable Head..........................................................11
2.5 Resulting Dimensions after Connecting User System Interface Cable.............................12
Section 3 Installing the MCU to the User System.............................................13
Section 4 Verifying Operation...........................................................................15
Section 5 Notice ................................................................................................16
Section 1 Configuration
CAUTION
Use an NQPACK144SD socket (manufactured by Tokyo
Eletech Corporation) for the FP-144 package IC socket
on the user system.
Figure 1 shows the configuration of the HS2643ECH61H user system interface cable for the
FP-144 package.
Figure 1 HS2643ECH61H User System Interface Cable
1
2
Table 1 lists the HS2643ECH61H components. Please make sure you have all of these components
when unpacking.
Table 1 HS2643ECH61H Components
No. Component Quantity Remarks
1 Cable body 1 Flat cable
2 Cable head 1
3 IC socket 1 For the FP-144 package
4 Socket cover 1 For installing a FP-144 packaged MCU
5 Screws (M2 x 10 mm) 4 For fastening cable head
6 Screws (M2 x 6 mm) 4 For installing a FP-144 packaged MCU
7 Guide pins (φ1 mm) 3 For determining the IC socket location
8 Screwdriver 1 For tightening screws
9 Documentation 1 User’s manual for HS2643ECH61H (this manual)
Section 2 Connection Procedures
2.1 Connecting User System Interface Cable to Emulator Station
WARNING
Observe the precautions listed below. Failure to do so
will result in a FIRE HAZARD and will damage the user
system and the emulator product or will result in
PERSONAL INJURY. The USER PROGRAM will be
LOST.
1. Always switch OFF the user system and the emulator
product before the USER SYSTEM INTERFACE CABLE
is connected to or removed from any part. Before
connecting, make sure that pin 1 on both sides are
correctly aligned.
2. The user system interface cable dedicated to the
emulator must be used.
To connect the cable body to the emulator station, follow the instructions below.
1. Make sure the user system and emulator station are turned off.
CAUTION
When connecting or removing the user system interface
cable, apply force only in the direction suitable for
connection or removal, while making sure not to bend or
twist the cable or connectors.
Otherwise, the connectors will be damaged.
2. After making sure the direction of the cable body connector is correct, firmly insert the cable
body connector into the emulator station socket (figure 2).
3
Emulator station
E6000
Cable body connector
User system interface cable
Figure 2 Connecting User System Interface Cable to Emulator Station
4
2.2 Connecting User System Interface Cable to User System
WARNING
Always switch OFF the user system and the emulator
product before the USER SYSTEM INTERFACE CABLE
is connected to or removed from any part. Before
connecting, make sure that pin 1 on both sides are correctly
aligned. Failure to do so will result in a FIRE HAZARD and
will damage the user system and the emulator product or
will result in PERSONAL INJURY. The USER PROGRAM will
be LOST.
To connect the cable head to the user system, follow the instructions below.
2.2.1 Installing IC Socket
After checking the location of pin 1 on the IC socket fasten it to the user system before soldering.
CAUTION
After confirming the location of pin 1 on the IC socket,
apply epoxy resin adhesive to the end of the four projections
at the bottom of the IC socket, and fasten it to the user
system.
Use the guide pins provided to determine where to install the IC socket, as shown in figure 3.
5
IC socket
(NQPACK144SD manufactured
by Tokyo Eletech Corporation)
User system
Guide pins
4 projections to apply
epoxy resin adhesive to
Bottom view of IC soket
Pin 1
Figure 3 Location Setting of IC Socket
2.2.2 Soldering IC Socket
After fastening, solder the IC socket for a FP-144 package to the user system.
CAUTION
Be sure to completely solder the leads so that the solder
slops gently over the leads and forms solder fillets. (Use
slightly more solder than the MCU.)
2.2.3 Inserting Cable Head
CAUTION
Check the location of pin 1 before inserting.
Align pin 1 on the IC socket for a FP-144 package on the user system with pin 1 on the user system
interface cable head, and insert the user system interface cable head into the IC socket on the user
system, as shown in figure 4.
6
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Renesas Computerhardware Handbücher
Renesas
Renesas Converter Board M30290T-80FPD Bedienungsanleitung
Renesas
Renesas HD49335HNP Bedienungsanleitung
Renesas
Renesas H8S/2655 Series Bedienungsanleitung
Renesas
Renesas R8C/13 Bedienungsanleitung
Renesas
Renesas HD74HCT1G04 Bedienungsanleitung
Renesas
Renesas R-IN32M4-CL2 TESSERA Montage- und Bedienungsanleitung
Renesas
Renesas H8S/2214 Series Bedienungsanleitung
Renesas
Renesas RL78 Series Montage- und Bedienungsanleitung
Renesas
Renesas RSKM16C6NK Bedienungsanleitung
Renesas
Renesas ASSP EASY Bedienungsanleitung
Renesas
Renesas RZ/A1H Series Bedienungsanleitung
Renesas
Renesas MCU Board for 4513/4514 Group MCUs... Bedienungsanleitung
Renesas
Renesas M3T-FLX100-R Bedienungsanleitung
Renesas
Renesas RA4 Series Bedienungsanleitung
Renesas
Renesas TFP-100G Bedienungsanleitung
Renesas
Renesas SuperH RISC Series Bedienungsanleitung
Renesas
Renesas 8V19N850 Bedienungsanleitung
Renesas
Renesas RH850/F1 Series Bedienungsanleitung
Renesas
Renesas F-ZTAT Series Bedienungsanleitung
Renesas
Renesas Compact Emulator M30620T-CPE Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
