Renishaw MP10 Bedienungsanleitung
Installation and user’s guide
H-2000-5059-05-A
MP10 probe system
© 2003 - 2005 Renishaw. All rights reserved.
This document may not be copied or
reproduced in whole or in part, or transferred
to any other media or language, by any
means, without the prior written permission
of Renishaw.
The publication of material within this
document does not imply freedom from
the patent rights of Renishaw plc.
Renishaw part no: H-2000-5059-05-A
Issued: 08.05
Disclaimer
Considerable effort has been made to ensure
that the contents of this document are free from
inaccuracies and omissions. However,
Renishaw makes no warranties with respect to
the contents of this document and specifically
disclaims any implied warranties. Renishaw
reserves the right to make changes to this
document and to the product described herein
without obligation to notify any person of such
changes.
Trademarks
Renishaw® and the probe emblem used in the
RENISHAW logo are registered trademarks of
Renishaw plc in the UK and other countries.
apply innovation is a trademark of
Renishaw plc.
All brand names and product names used in
this document are trade names, service marks,
trademarks, or registered trademarks of their
respective owners.
FCC DECLARATION (USA)
FCC Section 15.19
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired
operation.
FCC Section 15.105
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case
you will be required to correct the interference at your own expense.
FCC Section 15.21
The user is cautioned that any changes or modifications not expressly approved by Renishaw plc, or
authorised representative could void the user's authority to operate the equipment.
FCC Section 15.27
The user is also cautioned that any peripheral device installed with this equipment such as a
computer, must be connected with a high-quality shielded cable to insure compliance with FCC limits.
Installation and users guide - English
ASSOCIATED SYSTEM HANDBOOKS
Description Part No.
H-2000-5044
H-2000-5073
H-2000-5062
H-2000-5057
Optical module machine (OMM)
MI 12 interface unit
Optical machine interface (OMI)
PSU3 power supply unit
SAFETY
Before working inside machines, ensure
machine is in a safe condition
Switch off power before making electrical
connections, changing probe and receiver
settings and replacing components
WARRANTY
Equipment requiring attention under warranty
must be returned to your supplier. No claims
will be considered where Renishaw equipment
has been misused, or repairs or adjustments
have been attempted by unauthorised persons.
CHANGES TO EQUIPMENT
Renishaw reserves the right to change
specifications without notice.
CNC MACHINE
CNC machine tools must always be operated
by competent persons in accordance with
manufacturers instructions.
CARE OF THE PROBE
Keep system components clean and treat the
probe as a precision tool.
PROBE IP RATING X8
PATENT NOTICE
Features of MP10 probes and features of
similar probes are the subject of one or more of
the following patents and/or patent
applications:
EP 0337669
EP 0390342
EP 0695926
JP 2,945,709
JP 2,944,401 US 5,150,529
US 5,040,931
US 5,669,151
Contents 1-1
Software requirements ......................1-23
Typical probe cycles ..........................1-24
System flow charts.............................1-26
SERVICE and MAINTENANCE........1-29
Weak link for styli with steel shaft......1-29
Diaphragm inspection ........................1-30
Diaphragm replacement ....................1-31
SCREW TORQUE VALUES .............1-32
FAULT FINDING ...............................1-34
APPENDIX 1
ADAPTOR and EXTENSIONS ..........1-37
APPENDIX 2 PSU3 ..........................1-38
APPENDIX 3 OMM............................1-38
APPENDIX 4 MI 12 ...........................1-39
APPENDIX 5 OMI..............................1-40
PARTS LIST......................................1-42
SYSTEM INSTALLATION
Typical probe systems .......................1-2
Two OMMs and remote indicator ......1-3
Performance envelope ......................1-4
System performance..........................1-8
MP10 features ...................................1-9
MP10 dimensions ..............................1-10
Modes of operation ............................1-11
Options setting switch........................1-12
Enhanced trigger circuit .....................1-12
Battery covers and battery.................1-13
Stylus spring pressure adjustment ....1-15
Stylus on-centre adjustment ..............1-16
Probe/shank mounting.......................1-16
OPERATION
LEDs ..................................................1-2
Switch-on/switch-off...........................1-11
Probe moves......................................1-22
A workpiece set-up and inspection probe is in effect another
tool in the system. A probe cycle may be included at any
stage of the machining process.
Signals are transmitted between the probe and the machine
control, via the OMP and OMM + MI 12 or alternatively the
OMP and OMI.
TYPICAL PROBE SYSTEMS
1-2
Workpiece
Probe head
Stylus
Machine spindle
Typical tool
setting probe
CNC
machine
control
Cable
Battery cover
Shank (size 25 - 50)
Optional - PSU3
power supply unit
Optional - PSU3
power supply unit
OMP - LEDs
Mounting bracket
OMI (one only)
+ CNC control
Optional - PSU3
power supply unit
MP10
inspection
probe
3 x Receive diodes
6 x Transmit LEDs
1 x Probe status LED
MI 12 interface unit
or MI 12 board
OMM (one or two)
+ MI 12
+ CNC control
MI 5, MI 8 or
MI 8-4
interface
unit
SEE PAGES 1-38, 1-39 & 1-40
OMM - Optical module machine
OMP - Optical module probe
OMI - Optical machine interface
OMM TANDEM MOUNTING
Installations with exceptionally long
spindle travel, may require a
second OMM to cover signal
reception over the full working
envelope of the probe.
The reception cones of OMM 1
and OMM 2 overlap, so they
act as one receiver.
REMOTE INDICATOR
When the probe contacts a surface
an MI 12 LED changes state and a
bleep is emitted.
If the MI 12 is hidden from the
operator, a remote lamp or bleeper
may be placed in a position where
it is easily seen or heard.
OMM TWIN MOUNTING
Each spindle of a twin
spindle machine can
accept a probe.
Although both OMM 1
and OMM 2 are
switched on, only one
probe may be used at
any one time.
1-3
TWO OMMs AND REMOTE INDICATOR
CNC machine
control
MI 12
OMM 1
Spindle
travel
OMM 2
OMM 1
MI 12
Remote
indicator
CNC machine
control
OMM 2
MP10 35° OUTPUT PROBE + OMM
Probe and OMM diodes must be
mutually in each others field of view,
and within the performance envelope
shown.
OPERATING RANGE
The OMP must be within
6 m (19.6 ft) of the OMM.
PERFORMANCE ENVELOPE
1-4
SWITCH-ON/OFF RANGE
The OMP must be within
3 m (9.8 ft) of the OMM.
35° OMP
Optical
centre
line
OMM
60°
45°
60°
45°
15°
30°
30°
15°
0°
SWITCH ON/OFF
OPERATING
Range metres (feet)
2 (6.5)
1 (3.3)
3 (9.8)
4 (13.1)
5 (16.4)
6 (19.6)
45°
90°
15°
60°
15°
75°
45°
30°
30°
2 (6.5)
1
(3.3)
3 (9.8)
4 (13.1)
5 (16.4)
6 (19.6)
2 (6.5)
1 (3.3)
3 (9.8)
4 (13.1)
5 (16.4)
6 (19.6)
45°
90°
15°
60°
15°
75°
45°
30°
30°
60°
Probe and OMM diodes must be
mutually in each others field of view,
and within the performance
envelope shown.
SWITCH-ON/OFF RANGE
The OMP must be within
3 m (9.8 ft) of the OMM.
OPERATING RANGE
The OMP must be within
6 m (19.6 ft) of the OMM.
MP10 70° OUTPUT PROBE + OMM
PERFORMANCE ENVELOPE 1-5
SWITCH ON/OFF
OPERATING
Range metres (feet)
Optical
centre
line
2 (6.5)
3 (9.8)
4 (13.1)
5 (16.4)
6 (19.6)
OMM
60°
45°
60°
45°
15°
30°
30°
15°
1 (3.3)
70° OMP
0°
0°
1
(3.3)
3 (9.8)
OMI
60°
45°
60°
45°
15°
30°
30°
15°
2 (6.5)
1-6 PERFORMANCE ENVELOPE
MP10 35° OUTPUT PROBE + OMI
Probe and OMI diodes must be
mutually in each others field of view,
and within the performance envelope
shown.
SWITCH-ON/OFF RANGE
and OPERATING RANGE
The OMP must be within
3 m (9.8 ft) of the OMI.
Optical
centre
line
35° OMP
2 (6.5)
1 (3.3)
3 (9.8)
90°
15°
60°
15°
75° 30°
30°
SWITCH ON/OFF
OPERATING
Range metres (feet)
0°
45°
Inhaltsverzeichnis
Andere Renishaw Messgerät Handbücher
Renishaw
Renishaw TP7 Series Bedienungsanleitung
Renishaw
Renishaw SCP600 Bedienungsanleitung
Renishaw
Renishaw Equator 300 Bedienungsanleitung
Renishaw
Renishaw REVO Bedienungsanleitung
Renishaw
Renishaw P-GA01-0001 Bedienungsanleitung
Renishaw
Renishaw RENGAGE RMP400 Bedienungsanleitung
Renishaw
Renishaw OMP400 Bedienungsanleitung
Renishaw
Renishaw PH10 PLUS Series Bedienungsanleitung
Renishaw
Renishaw LP2 Bedienungsanleitung
Renishaw
Renishaw RENGAGE OMP600 Bedienungsanleitung
Renishaw
Renishaw OTS Bedienungsanleitung
Renishaw
Renishaw XK10 Bedienungsanleitung
Renishaw
Renishaw PH10 PLUS Series Bedienungsanleitung
Renishaw
Renishaw RMP40 Bedienungsanleitung
Renishaw
Renishaw OLP40 Bedienungsanleitung
Renishaw
Renishaw RMP40 Bedienungsanleitung
Renishaw
Renishaw MIH Bedienungsanleitung
Renishaw
Renishaw RP1 Bedienungsanleitung
Renishaw
Renishaw PH10M-iQ PLUS Bedienungsanleitung
Renishaw
Renishaw HCU2 Bedienungsanleitung
