Richmond GTR058 Bedienungsanleitung
GTR058 Installation Manual: Rev 22 1
Double Swing Gate Opener
User Manual GTR058
Instructions must be read before beginning installation. Please follow these instructions carefully,
incorrect installation could aect gate operation. If you require more information, please contact
your local Richmond Wheel & Castor Co branch.
AU: 1300 474 246 NZ: 0800 61 71 81 International: +613 9551 2233
For installation or troubleshooting assistance visit richmondau.com/gate-motor-support/
For accessories: please refer to the relevant accessory manuals for instructions on wiring them to the GTR058 motor.
Before starting we recommend watching the installation video that can be found at:
richmondau.com/product/gtr058-double-swing-gate-opener/
This video will give a detailed overview of the installation process and will serves as a useful aid during installation.
GTR058 Installation Manual: Rev 22 2
GTR058 Installation Manual: Rev 22 3
Contents:
General Safety 4
Parts List 5
Technical Specications 6
Features 7
Gate Arm Installation: Pull to Open (Standard)
Before you start/Tools Required 9
Gate Preparation 10
Step 1 – Post Bracket Assembly 11
Step 2 - Set the Motor to Manual Mode 13
Step 3 – Positioning the Gate Bracket & Opener 13
Step 4 – Setting the Minimum Clearances 15
Step 5 – Axing the Gate & Post Brackets 16
Step 6 – Mounting the Control Box 17
Step 7 – Running the Motor Cable 17
Step 8 – Connecting the Gate Arm 18
Step 9 – Adjusting the Travel Limit Switches 19
Programming and Wiring
Programming Features 20
Pairing Remote Controls 24
Control Board Wiring Diagram 25
Optional Installation: Setting the Gate as Push to Open
Push to Open Installation Instructions & Wiring 27-30
Troubleshooting 31
For accessories: please refer to the relevant accessory manuals for
instructions on wiring them to the GTR058 opener.
GTR058 Installation Manual: Rev 22 4
Thank you for choosing this swing gate opener. Please read the manual carefully before assembling and using it. Do
not leave out the manual if you send this product to a third party. This product complies with the recognised technical
standards and safety regulations. Our company has the right to change the instruction without prior notice.
General Safety:
Warning: Incorrect or improper use of this product can cause damage to persons,
animals or properties.
• Please ensure that the input voltage to the low voltage power supply used matches with the supply voltage of
gate opener (AC240V 50Hz).
• To avoid damaging gas, power or other underground utility lines, contact the relevant authority BEFORE
digging.
• All potential hazards and exposed pinch points of the gate must be eliminated or guarded prior to installation
of this gate motor.
• Never mount any device that operates the gate motor where the user can reach over, under, around or
through the gate to operate the controls. These must be placed at least 1.8m from any moving part of the
moving gate.
• Ensure power plug is disconnected from the power socket during installation or maintenance.
• Keep remote control and other control devices out of children’s reach, in order to avoid unintentional
activation.
• Never allow anyone to hang onto the gate while moving.
• Please ensure a warning sign provided is tted to the gate.
• If required, install infrared photocells (sold separately) to detect obstructions and prevent injury or damage.
• Instruct all users about the control systems provided and the manual opening operation in case of
emergency.
• Ensure that the power cable is connected to a RCD protected power outlet that has been installed by a
qualied electrician.
• Do not install the product in an explosive atmosphere or where there is any danger of ooding.
• This product was exclusively designed and manufactured for the use specied in the present documentation.
Any other use not specied in this documentation could damage the product and be dangerous.
• Only use original parts for any maintenance or repair operation. Richmond Wheel & Castor Co declines all
responsibility with respect to the automation safety and correct operation when other supplier’s components
are used.
• Do not modify the automation components, unless explicitly authorised by Richmond Wheel & Castor Co.
• The user must avoid any attempt to carry out any works or repairs on the motor, and should always request
the assistance of qualied personnel.
• This motor is suitable for use on one swing gates only.
• Anything which is not expressly provided for in these instructions is not allowed and will void warranty.
• Dispose of all packing materials (plastic, cardboard, polystyrene etc.) according to current guidelines.
Keep plastic bags and polystyrene out of children’s reach.
Please save these instructions for future use.
GTR058 Installation Manual: Rev 22 5
Parts List:
No. Picture Name Quantity
1Gate Opener
(1 with 1.5m cable, and
1 with 6m cable) 2
2Control Box 1
3Remote Controls
(Additional remotes can be purchased
separately. Part no: GTR058) 2
4Manual release key
(These keys are needed during power outage,
keep on hand) 2
5Post Bracket 4
6Post Pivot Bracket 2
7Gate Bracket 2
8Gate Warning Signage
(must be tted to gate) 4
Hardware
ø10 Washer
(14 pcs) ø8 Washer
(2 pcs) ø10 lock Washer
(14 pcs)
M10 Nut
(14 pcs) M8 Nut
(2 pcs)
M10x200 Bolt (8 pcs)
M10x75 Bolt
(4 pcs) M10x30 Bolt
(2 pcs) M8x30 Washer
(2 pcs)
12x40 Clevis Pin
(2 pcs) 12x30 Clevis Pin
(2 pcs) Hairpin Clip
(4 pcs)
GTR058 Installation Manual: Rev 22 6
Technical Specications:
Dual Arm - 2 gate openers used on a heavier single gate
Single Arm - 1 gate opener used per gate
Gate Length (m)
Gate Length (m)
Gate Weight (kg)Gate Weight (kg)
Weight of Gate by Length
Weight of Gate by Length
* Refer to table 1
Model GTR058
Input 240V/50Hz
Motor Voltage 24VDC
Power 80W each Gate Opener
Current 3A
Actuator Speed 16mm/s
Max. Actuator Travel 385mm
Max. Weight of Gate 400kgs per gate* (refer to table 1 below)
Max. Width of Gate 5mtrs per gate For dual gates longer than 4mtrs an extension cable is
required. 3m (GTR158) and 6m (GTR159) extension cables to suit available.
Ambient Temperature -20°C~ +50°C (-4°F to 122°F)
Noise ≤60dB
IP Protection Class IP44
Remote Control Frequency 433.92MHz
Package Weight 18kg
Table 1
Table 2
750
700
650
600
4 4.5 5 5.5
400
350
300
250
200
1.8 2.8 3.2 4 5
GTR058 Installation Manual: Rev 22 7
Features:
• Soft start and soft stop
• Emergency release key in case of power failure
• Dual/Single gate running mode
• Adjustable opening/closing interval between the Primary and Secondary gate.
• Stop/Reverse in case of obstruction during gate opening/closing.
• Built in adjustable auto-close (0-99 seconds)
• Built in max. Motor running time (MRT) adjustable for multiple safety protection (1-50 seconds)
• Digital display indicates the running situation and setting menu
• Reliable electromagnetism limit for easy adjustment
• Comes with 2x pre-programmed remotes. Additional remotes can be purchased separately.
• Can be equipped with a wide range of accessories, visit our website to see the full range of
accessories available: richmondau.com/automatic-gate-openers-hardware/
GTR058 Installation Manual: Rev 22 8
Gate Arm Installation:
Before you start:
The GTR058 Swing Gate Automation Kits are suitable for gates up to 400kg per arm not exceeding 5m in length. Refer
to Table 1 (page 6) to verify that your gate will be suitable. The motor arm uses a worm gear actuator to move your gate.
The swing gate openers must be installed on the inside of the property.
The control box comes with a 1.5m 10 amp 3 pin power cable. This should be plugged into an appropriate weatherproof
power outlet, which must be installed by a qualied electrician. Do not extend the power cable. Make sure the power
cord is protected from ooding, tripping and any other damage. If in any doubt, we recommend shielding all cables with
electrical conduit.
Please Note: This gate kit is FACTORY set to be a PULL to OPEN.
If you require a PUSH to OPEN setting please refer to Page 27 for PUSH to OPEN instructions
Inside
Outside
Inside
Outside
Is the gate being installed as Pull to Open or Push to Open?
Pull to Open Default Setting
Gate opens inwards towards the property
Refer to page 11 for pull to open instructions Refer to page 27 for push to open instructions
Please note: your gate must never open into public spaces
Push to Open Optional Setting
Gate opens outwards from the property
GTR058 Installation Manual: Rev 22 9
Tools Required for Installation:
• Power Drill & Drill Set
• Tape Measure
• Open End Wrenches – #14 & #17 orAdjustable Wrenches
• C-Clamps: Small, medium, and large
• Level
• Hacksaw or Heavy Duty Bolt Cutters
• Phillips Head Screwdriver
• ø40mm or ø20mm Electrical Conduit (enough to cover the width of your gate opening)
If using ø20mm conduit the motor plug for gate motor 2 will need to be cut and wired back into the control
box. Refer to the control board wiring diagram on page 25 (for pull to open) or page 27 (for push to open)
We recommend getting an extra person to help with installation if possible
GTR058 Installation Manual: Rev 22 10
Gate Preparation:
Check that the swing gate is correctly installed and level, and that the gate hinges/bearings are greased and in good
condition. Any misalignment or binding in the setup of the gate may cause problems with the gate opener or diculties
opening the gate.
This gate arm is to suit Pull-to-Open installation, in which the gate opens into the property. The gate arm can also be
used for Push-to-Open installation, see Page 27 of this manual for more details.
Ensure that the gate does not open into public areas.
The gate opener connects to the gate and to the gate post. The Post Brackets can be tted to a round or square post.
When mounting the Post Brackets, use bolts long enough to pass through the entire post.
M10 x 200m bolts are included. Concrete anchors are not provided.
When mounting the Post Brackets to wooden posts, a larger-size washer or metal plate should be used between the
bolts and the wooden post to ensure the stability of the fastening hardware. If the post is smaller than 6" diameter
or square, it should be made of metal and set in cement.
Fig 1
Andere Handbücher für GTR058
2
Inhaltsverzeichnis
Andere Richmond Toröffner Handbücher
Richmond
Richmond GTR062 Bedienungsanleitung
Richmond
Richmond GTR064 Bedienungsanleitung
Richmond
Richmond GTR500 Bedienungsanleitung
Richmond
Richmond GTR502 Bedienungsanleitung
Richmond
Richmond GTR058 Bedienungsanleitung
Richmond
Richmond GTR064 Bedienungsanleitung
Richmond
Richmond GTR207 Bedienungsanleitung
Richmond
Richmond GTR181 Bedienungsanleitung
Richmond
Richmond GTR064 Bedienungsanleitung
Richmond
Richmond GTR099 Bedienungsanleitung
