Ricoh PRIPORT VT2130 Bedienungsanleitung

I{IIGOM

PRIPORTVT2130

OPERATINGINSTRUCTIONS

Ill

p’

RICOH COMPANY, LTD.

Note to users in the United States of America

This equipment has been tested and found to comply with the limits for a

Class Adigital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in acommercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in aresidential area is

likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Note to users in Canada

This digital Apparatus does not exceed the Class Alimits for Radio

Frequency noise from Digital Apparatus set out in the Radio Interference

Regulations of the Canadian Department of Communications.

Remarque concernant Ies utilisateurs au Canada

Le present appareil numerique n’emet pas de bruits radioelectriques

depassant Ies Iimites applicable aux appareiis numeriques de la classe

Aprescribes clans Ie R&glement sur Ie brouillage radioelectrique edicte

par Ie ministere des Communications du Canada.

INTRODUCTION

The Ricoh Priport VT2130 is astencil duplicator which is carefully

manufactured to exacting standards of high performance.

This manual contains detailed instructions on the operation and care of the

Priport VT21 30. To get the maximum versatility from this machine, all

operators should read and follow the instructions in this manual. Please keep

this manual in ahandy place near the machine.

1. Wide range of reproduction ratios:

4fixed reproduction ratios (100% plus 3reduction ratios).

2. 2single originals can be printed on one sheet of paper.

3. 5mono color printing with optional drum units.

TABLE OF CONTENTS

GUIDE TO COMPONENTS

1. Machine Exterior ........................2

2. Machine Interior ..........................4

3. Operation Panel ..........................6

INSTALLATION REQUIREMENTS

1. Machine Environment .................8

2. Access to Machine .....................9

3. Power Connection ......................9

DO’S AND DON’TS ............................... 10

ORIGINALS ......................................0.... 11

PRINTING PAPER ................................ 13

OPERATION

10.

11.

Preparation for Printing ............14

Setting the Originals ................. 16

Printing ..................................... 17

Restoring Paper Feed and

Paper Delivery Tables ............... 18

Adjusting the Image Position ...19

Changing the Paper Size ..........21

Printing on Thick or Thin

Paper .........................................22

Printing on Postcard Size

Paper .........................................23

Various Originals ......................24

Changing the Printing Speed ...25

To Stop the Machine During a

Printing Run ..............................26

12. Changing the Drum Unit for

Color Printing ............................27

13. Printing in Two Colors ..............29

SPECIAL FUNCTIONS

1. Group Printing from the Same

Original ....................................30

2. Combine 2Originals .................32

3. Various Run Lengths Using

the Same Master .......................34

4. Photo Mode Printing .................35

REPLENISHING SUPPLIES

1. Loading Paper ...........................36

2. Supplying Ink ............................37

3. Master Roll Replacement ..........38

MAINTENANCE

1. Thermal Head Cleaning ...........40

2. Platen Cover/Exposure Glass ..41

TROUBLESHOOTING

1. Indicators ..................................42

2. When the Misfeed (8%) Indicator

.-.

Lights ........................................43

When the Supply/Exchange ~)

Indicator Lights ........................49

Other Indicators Light ...............51

Poor Printing .............................52

MISCELLANEOUS ................................54

1. Operating Cautions ........----- 54

SPECIFICATION ...................................56

GUIDE TO COMPONENTS

1. Machine Exterior

1111

b‘%Q

12 3

1’5

p–

1.Top Unit

2.Original Guides

3.Original Table

4. Original Table Release

Lever

5.Feed Roller Pressure

Lever

6.Separation Roller

Pressure Lever

7. Paper Feed Side Plate

8.Paper Feed Table

9. Side Plate Fine

Adjusting Dial

10. Front Door

11. Paper Delivery Table

12.Operation Panel

13.Original Tray

Open to remove the misfed original.

Adjust these guides to position the originals

correctly.

Place the originals on this table.

Use to open the original table unit to the left

for master installation.

Use to adjust the contact pressure of the

paper feed roller according to paper thickness.

Use to adjust the separation roller pressure to

prevent double feed.

Use to prevent paper skew.

Set the paper on this table.

Use to shift the paper feed table sideways.

Open for access to the inside of the machine.

Completed prints are delivered here.

Operator controls and indicators are located

here.

Originals used to make amaster are delivered

to this tray.

2. Machine Interior

19‘

24 25 14 15

Ii= \’18

14. Master Cut Button Press this button to cut the master paper lead-

15. Pressure Release Lever

16. Drum Rotation Button

17.Drum Unit

18. Ink Holder

19.Main Switch

20. Small Size Paper

Delivery End Plate

(for smaller than

81/2”x 1l“)

21. Paper Delivery End

Plate

(for larger than

81/2” x1l“)

22. Paper Delivery Side

Plate

23. Master Eject Container

Cover

24.Printing Density Select

Switch

25.Master Eject Unit Open

Button

ing edge after installing anew master roll.

Use to install the master roll, or to clean the

thermal head.

Press to replace the drum or to remove misfed

paper.

The master paper is wrapped around this unit.

Set the ink cartridge in this holder.

Use to turn the power on or off.

Use to align the leading edge of small-sized

(less than 81/2” x11”) prints.

Use to align the leading edge of prints larger

than 81/2” x1l“.

Use to align the prints on the paper delivery

table.

Open when removing the master eject box.

Use to select the printing density according to

the type and quality of the original.

Press to remove misfed paper or amisfed

master.

3. Operation Panel

1234

t11

Auto Cycle

Lower Cornblne 2originals

Q%=%

IO(I 93 75 64

(0000)

1. Reset Key

2. Indicators

3. Auto Cycle Key

4. Reduction Key

5. Image Position

Keys

6. Number Keys

7. Counter

8. Memory Display

9. Print Start Key

10. Master Making Key

11. Proof Key

18 17 16

Press to reset error indicators.

Light or blink when anon-standard condition

occurs within the machine. (See page 42.)

Use to automatically process masters and

make prints.

Press to reduce the image.

Press to shift the image forwards or back-

wards on the print paper.

Press to enter the number of prints.

Displays the number of prints entered. While

printing, it shows the number of uncompleted

prints.

Displays the number of the memory location

that will be used to store the number of

copies. The print number for up to 10 jobs

can be stored at once.

Press to start printing.

Press to make amaster.

Press to make trial prints or extra prints.

567 8

15 14 13 12 11 10 9

12. Stop Key Press to stop the machine operation. The

machine will continue operation when the Print

Start key or Master Making key is pressed.

13. Memory Key Use to select memory location number. (1 -10)

14. Clear Key Press to change the number set in the

counter. This key can be used only after the

machine stops operation.

15. Speed Keys Press to adjust the rotation speed of the

machine according to the type of image and

printing paper.

16. Image Mode Key Press to select line mode or photo mode ac-

cording to the type and quality of the original.

17. Combine 2Press to

Originals Key image.

18. Lower Paper Feed Press to

Table Key

combine two originals onto

lower the paper feed table.

one print

Inhaltsverzeichnis

Andere Ricoh Multifunktionsdrucker Handbücher

Ricoh

Ricoh BizWorkz 106 Bedienungsanleitung

Ricoh

Ricoh 3045 - Aficio B/W Laser Bedienungsanleitung

Ricoh

Ricoh Aficio MP 1100 Bedienungsanleitung

Ricoh

Ricoh Aficio MP 4000 Bedienungsanleitung

Ricoh

Ricoh FT6655 Bedienungsanleitung

Ricoh

Ricoh Priport JP750 Bedienungsanleitung

Ricoh

Ricoh C275 Bedienungsanleitung

Ricoh

Ricoh SP 112 Bedienungsanleitung

Ricoh

Ricoh B234 Bedienungsanleitung

Ricoh

Ricoh C3828 Bedienungsanleitung

Ricoh

Ricoh Priport 1250 Bedienungsanleitung

Ricoh

Ricoh D104 Montageanleitung

Ricoh

Ricoh B022 Bedienungsanleitung

Ricoh

Ricoh DX 3443 Bedienungsanleitung

Ricoh

Ricoh 2018 Bedienungsanleitung

Ricoh

Ricoh Aficio MP C3500 Bedienungsanleitung

Ricoh

Ricoh Aficio 220 Bedienungsanleitung

Ricoh

Ricoh Aficio MP C3500 Bedienungsanleitung

Ricoh

Ricoh Aficio MP C3500 Bedienungsanleitung

Ricoh

Ricoh FAX3310LE Bedienungsanleitung

Ricoh

Ricoh Pro C900 Stücklistenhandbuch

Ricoh

Ricoh Aficio SP 1200SF Bedienungsanleitung

Ricoh

Ricoh Aficio 850 Bedienungsanleitung

Ricoh

Ricoh C222DN - Aficio SP Color Laser Printer Kurzanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung

Oce

Oce VarioLink 5022 Bedienungsanleitung