Ricoh Pro C5300 Series Bedienungsanleitung

2Throughput

CIP Training

Pro C5300 series

1. Auto Document Feeder (ADF)

Lower the ADF over originals placed on the exposure glass.

If you load a stack of originals in the ADF, the ADF will automatically feed the originals one by one.

The ADF scans both sides of an original simultaneously.

2. Exposure glass

Place originals face down here.

CIP Training Pro C5300 series

Throughput

Startup and Shutdown.

Front and left view

3. Control panel

See “Control Panel” module for detailed information.

4. Front cover

Open to replace the toner cartridge.

5. Drawer

Pull out the drawer when a paper jam occurs.

6. Paper trays (Trays 1–3)

Load paper here. Tray 1 is a tandem tray where paper on the left side automatically moves to the

right when paper there has run out.

7. Front lower left cover

Open to replace the waste toner bottle.

8. Main power switch

To turn the power on and off, open the cover of the main power switch and press the main power

switch.

•

To turn the machine on and off, press the main power switch on the left side of the machine.

Turning On the Main Power

1. Make sure the power cord is ﬁrmly plugged into the wall outlet.

2. Open the cover of the main power switch on the left side of the machine,

and push the switch.

Do not push the main power switch repeatedly.

When you push the main power switch, wait at least 10 seconds after it is conﬁrmed that the main

power indicator has lit up or gone out.

If the main power indicator does not light up or go out in 5 minutes after you push the main power

switch, contact your service representative.

CIP Training Pro C5300 series

Throughput

Turning On/Off the Power

The main power indicator on the right side of the control panel turns on.

•When the power is turned on, the screen may show that the machine is performing an

auto restart. Do not turn off the main power while the machine is processing. It takes

about 7 minutes until the machine restarts.

•If a file was deleted from memory, a Power Failure report is automatically printed as

soon as the power is restored. This report can be used to identify lost files.

Turning Off the Main Power

• When disconnecting the power cord from the wall outlet, always pull the plug, not the cord.

Pulling the cord can damage the power cord. Use of damaged power cords could result in ﬁre

or electric shock.

1. Open the cover of the main power switch on the left side of the machine, and push the switch.

The main power indicator on the right side of the control panel turns off. The main power turns off

automatically after the machine has shut down properly.

Saving Energy

When the machine is not operated for a specified period of time, the machine enters the "Energy

Saving mode" automatically. There are the following two steps of Energy Saving mode:

1. Fusing Unit Off Mode or Low Power Mode

2. Sleep Mode

Fusing Unit Off mode and Low Power mode cannot be used at the same time.

By default, the machine first switches to Low Power mode and then to Sleep mode after a lapse of

time.

•Do not turn off the power while the machine is in operation. To turn the power off, confirm that the

operation is finished.

•Do not hold down the main power switch while turning off the main power. Doing so forcibly turns off

the machine's power and may damage the hard disk or memory and cause malfunctions.

•Do not press the main power switch soon after pressing the main power switch on the machine. When

you turn the power on or off, wait at least 10 seconds after confirming that the main power indicator on

the control panel has turned on or off.

•The fan inside the machine near the vents may continue running to cool the machine after a large print

job. While the fan is running, do not turn off the main power nor disconnect the power cord from the

wall outlet.

CIP Training Pro C5300 series

Throughput

Sleep Mode

Low Power Mode

In this mode, the control panel display turns off and the main power indicator remains lit. If the

machine is left idle for a specific time, it switches to Low Power mode.

•Low Power mode cannot be used if Fusing Off mode is enabled.

•You can change the amount of time that the machine waits before switching to Low Power

mode under [Low Power Mode Timer].

•If you touch the control panel in Low Power mode, the machine exits the mode and the control

panel display turns on.

In this mode, the main power indicator is lit. Because the heater of the fusing unit is turned off but

the screen of the control panel is still displayed, the power consumption decreases, but you can start

operation promptly. If you do not operate the machine for a specified period of time, the machine

emits a clicking sound and enters Fusing Unit Off mode.

•You can specify whether to enable the Fusing Unit Off mode and the time to wait before the

machine enters Fusing Unit Off mode under [Fusing Unit Off Mode (Energy Saving) On/Off].

•In this mode, you can scan documents, send faxes, receive faxes into memory, change the

machine settings on the control panel, and perform other operations that do not require

printing.

CIP Training Pro C5300 series

Throughput

Fusing Unit Off Mode

In this mode, the display of the control panel turns off and the main power indicator blinks slowly.

Power consumption is minimized. When you do not operate the machine for a specified period of

time or press [Energy Save], the machine enters Sleep mode.

1. You can specify the amount of time that the machine waits before entering Sleep mode under

[Sleep Mode Timer].

2. The machine recovers from Sleep mode when you perform one of the following:

•Lift the ADF.

•Place an original in the ADF.

•Touch the display of the control panel.

The energy saving functions are disabled when an error occurs or while an operation is in progress.

The energy saving functions will not operate in the following cases:

•When fixed warm-up is in progress

•When operations are suspended during printing

•When a warning message appears (The machine enters Fusing Unit Off mode unless the cover is

open.)

•When paper is jammed (The machine enters Fusing Unit Off mode except when the cover is

open.)

CIP Training Pro C5300 series

Throughput

Adding/Replacing Toner bottles

•Replace the toner after the message prompting replacement is displayed on the control panel.

•The machine may become damaged if you use toner of a different type.

•Do not turn off the power of the machine when replacing the toner. If you turn off the power

when replenishing the toner, the specified settings are canceled, and printing will not resume

afterwards.

•Store the toner in a dry environment away from direct sunlight and generally under the

temperature below 35°C.

•Keep the toner horizontal when storing it.

•After removing the print cartridge from the machine, do not shake it while its opening is facing

downward. The remaining toner may spill out.

•After removing the toner cartridge, do not touch the interior of the machine.

•Do not pull out and put back the toner cartridge repeatedly. The remaining toner may leak.

•Follow the procedure displayed on the screen to replenish the toner.

•Keep the Waste Toner Bottle that is provided with the toner kit for replacement.

You can view the procedure to replace the toner by watching a movie that is displayed on the

control panel.

1. Press [Watch Video].

Press [Check Status] and then press [Check] under "Mach. Status" on the [Mach./Applic. Stat] tab.

2. Press the play ( ) key.

3. Replace the toner by following the procedure shown in the video.

If appears when there is a lot of toner, hold the cartridge with the opening upward, shake

it well, and then reinstall it.

31,000 sheets per bottle of black toner

26,000 sheets per bottle of cyan toner

26,000 sheets per bottle of magenta toner

26,000 sheets per bottle of yellow toner

Coverage 8.75%, A4

Note: The toner yield targets are based on the average coverage given at standard conditions on

uncoated A4 paper recommended for the Ricoh C5300s Series. Actual yields may vary depending on

individual conditions.

Supply Yields

https://www.ricoh.com.au/support/my-device/recycle

Recycle: Ricoh consumable recycling

Our consumable recycling program is free to our customers as part of our goal to reach zero

waste-to-landll. Setting the industry benchmark, the program has recycled over 1,104 tonnes

of toner cartridges. The program includes a free pickup service for qualifying customers and

a Reply Paid return service.

CIP Training Pro C5300 series

Throughput

Adding/Replacing Toner bottles

Precautions When Storing Toner

•Do not store toner (new or used) or toner containers while toner is inside in a place with

an open flame. The toner can ignite and result in burns or fire.

Do not leave the following items in a place where children can reach them:

•Toner (new or used)

•Toner containers while toner is inside

•Toner-attached parts

When Paper or an Original Is Jammed

Remove the jammed sheet by following the procedure described in the animated illustration

displayed on the control panel. If paper jams occur frequently, check that the actual paper size in the

tray, the paper size dial and the [Tray/Paper Settings] displayed on the control panel are the same.

Be careful not to rip the jammed paper and leave small pieces inside the machine when removing.

Hold on the left and right edges of the paper firmly and apply force evenly to pull out the paper.

•There are highly-heated parts inside the machine. When removing misfed paper, do not touch

areas other than those specified in this manual. Touching those areas can result in burns.

•When replacing paper or removing jammed paper, make sure not to trap or injure your fingers.

•When operating the machine, do not put your hand inside the booklet finisher tray of the

finisher's staple unit. You may trap your fingers in the machine's gap and injury can result.

CIP Training Pro C5300 series

Throughput

•When clearing misfeeds, do not turn off the power. If you do, your copy settings will be lost.

•To prevent misfeeds, do not leave any torn scraps of paper inside the machine.

•Do not turn off the power of the machine when removing the jammed paper. If you turn off

the power, the specified settings values are reset.

•Only perform the operation described in the animated illustration. Failure to do so may

degrade the print quality or cause a malfunction.

•If the error message remains displayed even after you remove misfed paper, fully open the

front cover, and then close it.

•When removing jammed paper, you can touch only those areas explicitly indicated in the

manual.

•Do not remove the fusing unit. Doing so will result in loss of print quality.

•Inside the finisher, or inside the front cover, there are stickers or sheets explaining how to

remove misfed paper.

•If a detailed removal instruction appears on the right of the screen, follow it.

•You can also use the procedure indicated in the [Check Status] screen to remove jammed

paper.

•When a misfeed occurs inside the machine, the lamp on the center of the drawer flashes and

the drawer opens automatically. Remove the jammed paper by following the procedures

indicated in the animation that appears on the screen.

•If coated paper frequently becomes jammed and causes "U" to appear, contact your service

representative.

•When you close the upper right cover of the machine while the bypass tray is closed, be sure to

push the mark on the bypass tray, not the upper right cover.

•When you open the upper left cover of the wide large capacity tray to remove misfed paper, open

the upper left cover completely until it stops.

•When opening the drawer, make sure to completely pull it out toward you. If the cover of the

fusing unit is caught with the main unit, hold the handle at the center of the drawer and pull the

drawer out forcibly so that the whole fusing unit protrudes from the front cover.

CIP Training Pro C5300 series

Throughput

•When you close the upper right cover of the machine while the bypass tray is open, push the

mark on the upper right cover.

Andere Handbücher für Pro C5300 Series

Inhaltsverzeichnis

Andere Ricoh Multifunktionsdrucker Handbücher

Ricoh

Ricoh AC205 Bedienungsanleitung

Ricoh

Ricoh 80 Series Bedienungsanleitung

Ricoh

Ricoh 3245 - Type Print Server Service-Handbuch

Ricoh

Ricoh PRO C9100 Service-Handbuch

Ricoh

Ricoh Aficio 1015 Bedienungsanleitung

Ricoh

Ricoh DD 5450 Bedienungsanleitung

Ricoh

Ricoh MP C3003 Bedienungsanleitung

Ricoh

Ricoh Aficio 3260C Bedienungsanleitung

Ricoh

Ricoh A156 Bedienungsanleitung

Ricoh

Ricoh Aficio MP 5500 Bedienungsanleitung

Ricoh

Ricoh Priport HQ7000 Bedienungsanleitung

Ricoh

Ricoh MP 305+ series Merkblatt

Ricoh

Ricoh SP 311DN Bedienungsanleitung

Ricoh

Ricoh Pro C9200 Bedienungsanleitung

Ricoh

Ricoh Aficio SP 4110n Bedienungsanleitung

Ricoh

Ricoh Aficio AP3200 Bedienungsanleitung

Ricoh

Ricoh Aficio 2045e Service-Handbuch

Ricoh

Ricoh Aficio 401 Bedienungsanleitung

Ricoh

Ricoh Aficio MP C2000 Bedienungsanleitung

Ricoh

Ricoh Aficio MP C305 Bedienungsanleitung

Ricoh

Ricoh SP C435DN Bedienungsanleitung

Ricoh

Ricoh Aficio MP 171F Bedienungsanleitung

Ricoh

Ricoh B174 Bedienerhandbuch

Ricoh

Ricoh MP 7503SP Kurzanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung

Oce

Oce VarioLink 5022 Bedienungsanleitung