Ricoh MET-C2yz Service-Handbuch

Technical Bulletin PAGE: 1/5

Reissued: 13-Mar-17

Model: MET-C2yz

Date: 13-May-16

No.: RD244001i

RTB Reissue

The items in bold italics have been corrected or added.

Subject: Firmware Release Note: System/Copy

Prepared by: M. Kumagai

From: 1st Tech Service Sect., MFP/Printer Tech Service Dept.

Classification:

Troubleshooting

Mechanical

Paper path

Part information

Electrical

Transmit/receive

Action required

Service manual revision

Retrofit information

Product Safety Other (Firmware)

Tier 2

This RTB has been issued to announce the firmware release information for the

System/Copy.

Version

Program No.

Effective Date

Availability of RFU

1.11

D2395550S

March 2017 production

Available

1.10

D2395550R

January 2017 production

Available

1.09

D2395550Q

December 2016 production

Available

1.08

D2395550P

November 2016 production

Available

1.07

D2395550N

October 2016 production

Available

1.06

D2395550M

September 2016 production

Available

1.05

D2395550L

August 2016 production

Available

1.04

D2395550K

July 2016 production

Available

1.03.1

D2395550J

May 2016 production

Available

1.03

D2395550H

1st Mass production

Available

Note: Definition of Availability of RFU via @Remote

“Available”: The firmware can be updated via RFU or SD card.

“Not available”: The firmware can only be updated via SD card.

Version

Modified Points or Symptom Corrected

1.11

Symptom corrected:

-The Eco-friendly counter may not appear, if the counter display timing

is set to initial log-in.

-SC819 may occur, if the auto log-out timer and the energy saving timer

are set to the same value.

-SC819 may occur after removing a jam that occurred while printing a

large job that fully consumes the printer memory.

-Communication may be impossible after changing the relationship

between host name and IP address on DNS server.

-SC899 may occur when rebooting after updating a firmware.

-When attempted to reboot the machine to resolve an SC, the message

"Reboot will done automatically" appears but the machine is not

rebooted.

-When started up in the Classic Copy application, the manual tray is

selected even if set to auto tray.

-Setting paper on the Bypass tray automatically assigns the Bypass tray

as the feed tray.

-If the Bypass tray is set to Auto paper detection and a jam occurs due

Technical Bulletin PAGE: 2/5

Reissued: 13-Mar-17

Model: MET-C2yz

Date: 13-May-16

No.: RD244001i

Version

Modified Points or Symptom Corrected

to a paper size mismatch, jam alert does not appear.

- The operation panel may freeze, if the Start button is pressed in copy

mode immediately after recovering from the energy saver mode.

- If an original jams in the sample copy of a stapled job, the first set is

not printed out.

Other changes:

Reduced time for controller firmware update and improved progress bar

feature.

1.10

Symptom corrected:

- SC819 occurs at boot-up.

- After entering the user code to start up the Copy application, the user code

input screen does not disappear.

- If a jam occurs on the first page of a job on a machine set with user code

authentication and then, the start button and log-out button are pressed

together, the start button becomes ineffective.

- Remaining printing time displayed is incorrect (e.g. 999min) for jobs printed

from the document server.

- When the device is using "Card Authentication Package" or another custom

authentication and then the following fields on the server are blank, the fields

in the address book on the device might not be overwritten:

- Email address

- FAX address

- Folder address

Other changes:

More than five languages can be added to the "Change Langs. Widget" on the

smart operation panel.

1.09

Symptom corrected:

- Erase Border works incorrectly when selecting the original paper size with

two spread pages.

- SC899 may occur when installing @Remote.

- Cannot recovery from energy saving mode and SC672-11 may occur.

- Connection error message may appear mistakenly on @Remote connected

machines.

- SC991/SC899 may occur or stall may occur during use of application on

@Remote connected machines.

- Connection may fail if entering and recovering from energy saving mode is

repeated without power OFF/ON on @Remote connected machines.

Other changes:

- To enable quicker the detection time and shut down time when SC670

occurs.

- When executing a Firmware configuration task via Device Manager NX

Pro/Enterprise, an RFU package with the appropriate destination

(USA/Europe/Asia/Korea/Taiwan model or China model) can be selected and

downloaded from the RICOH Global Server.

1.08

Symptom corrected:

1. Behavior of the SDK applications (CAP/ELP/SLNX/GSNX/etc.) may be

incorrect or inconsistent as described below. Both the Standard

Technical Bulletin PAGE: 3/5

Reissued: 13-Mar-17

Model: MET-C2yz

Date: 13-May-16

No.: RD244001i

Version

Modified Points or Symptom Corrected

(Compatibility mode) and SOP Optimized (Hybrid mode) applications are

affected by these issues.

- Cannot log in.

- Cannot scan.

- Cannot print.

- Error message appears.

- etc.

2. When feeding from the by-pass tray, the Start key may falsely become active

before specifying the paper size.

3. Error 22 may occur during ARFU.

4. When an application accesses the HDD after turning ON the power, the

machine may stall.

5. SC899 may occur after updating with the packaged firmware.

6. If the device enters Energy Save Mode after automatically logging out an

account, the device might stall when IC card authentication is used to

recover from Energy Save Mode.

Other changes:

Added an SP setting for enabling or disabling the "Screen Monitoring" function.

SP5-885-205: default = 0 ("Screen Monitoring" is enabled)

This firmware is dependent on Web Support firmware v1.04 (D2395561F) or

later, so please be sure to update that firmware as well.

1.07

Symptom corrected:

- Machine may stall, if scanned using the single pass DF.

- Saving a scanned filed onto a USB memory stick may cause the file to

corrupt.

- Recovering from the energy saver mode takes about 5 seconds longer than

usual.

Other changes:

- The default values of the following SPs were modified to enable faster

machine start-up when ejecting paper to the finisher tray.

MPC3004, MPC3504: SP1-107-007: 118 ->128

MPC2004: SP1-107-007: 121 ->131, SP1-1108-007: 121 -> 131

MPC2504: SP1-107-007: 118 -> 128, SP1-1108-007: 118 -> 128

1.06

Symptom corrected:

- Package RFU update may fail.

- If logged in using CAP and the device enters Energy Save mode, the device

may stall and logging out will fail.

1.05

Symptom corrected:

- Cannot enter the SP mode, if the proximity sensor activates during the enter

process.

- SC819 may occur at start up.

- Wrong fonts are used in some operation screens and the Web Image

Monitor.

- Error occurs, if new addresses are continuously registered to the address

book using Smart SDK.

- Installation of the SLNX Hybrid mode application may not be completed.

- Support for AirPrint.

This firmware is dependent on the following firmware modules. Please be

Technical Bulletin PAGE: 4/5

Reissued: 13-Mar-17

Model: MET-C2yz

Date: 13-May-16

No.: RD244001i

Version

Modified Points or Symptom Corrected

sure to update all of them:

- Printer firmware: v1.02 or later (D2395570F)

- Network Support firmware: v15.55 or later (D2395567F)

Other changes:

1. In response to concerns regarding vulnerability, the SSL/TLS setting in the

MFP matches that in the @Remote connection.

Explanation:

The MFP connects to the @Remote center server by using the TLS 1.1 or lower-

level protocol, which is not selectable from the customer site. This specification

change allows the CE and the customer to select the available protocol between

the MFP and @Remote center server by changing the SSL/TLS setting via Web

Image Monitor.

Important notes:

Before updating the firmware, please check the SSL/TLS setting and allow the

following security-level for each case. Otherwise, the @Remote service cannot

be provided:

For embedded type

- Allows TLS 1.1 or lower-level

- We are currently preparing the TLS 1.2 connection on the @Remote center

server. The scheduled date of completion will be announced soon.

- This will change when preparation at the @Remote center server is

complete.

For RC Gate A1

- Allows TLS 1.0 or lower-level

For RC Gate

- Allows SSL 3.0

1.04

Symptom corrected:

- Firmware for a different paper bank can be updated.

- Time needed to recover from the energy saving mode is different when

recovered by submitting a job or by touching the operation panel.

- SC819 may occur when recovering from the energy saving mode by

touching the operation panel.

- Cannot switch to the batch mode during a Smart Copy application job.

- Error message appears, if the procedure below is followed from the Quick

Print Release application:

1. Save a job with a password.

2. Enter the password in the Quick Print Release application.

3. Change the password of the job in Web Image Monitor.

4. See the preview in the Quick Print Release application.

- If a user ID is input manually and then an IC card of a different user is

hovered over the card reader, the user ID manually input is overwritten with

the user ID of the IC card.

- Log out confirmation screen may not appear when the System Settings

menu is logged out by an administrator.

Technical Bulletin PAGE: 5/5

Reissued: 13-Mar-17

Model: MET-C2yz

Date: 13-May-16

No.: RD244001i

Version

Modified Points or Symptom Corrected

- If the authentication setting is changed while logging in and the Finish key is

pressed from the System Settings menu, the System Settings menu appears

instead of the home screen.

- SC991 may appear and the controller logs are not saved, if entered the

energy saving mode with all of the following conditions met:

1. Sleep timer setting: 1 min

2. Approximately sensor: 0: OFF

3. Energy saving mode - STR setting (SP5-191-001: Power Str Set): 0:

OFF

- When LDAP Authentication or Windows Authentication is used and login

fails, the machine might beep twice.

1.03.1

Symptom corrected:

Shutdown process takes too long. (This process takes place only in the factory

using a special application.)

1.03

1st Mass production

Technical Bulletin PAGE: 1/2

Reissued: 21-Dec-16

Model: MET-C2yz

Date: 13-May-16

No.: RD244002f

RTB Reissue

The items in bold italics have been corrected or added.

Subject: Firmware Release Note: Engine

Prepared by: M. Kumagai

From: 1st Tech Service Sect., MFP/Printer Tech Service Dept.

Classification:

Troubleshooting

Mechanical

Paper path

Part information

Electrical

Transmit/receive

Action required

Service manual revision

Retrofit information

Product Safety Other (Firmware)

Tier 2

This RTB has been issued to announce the firmware release information for the Engine.

Version

Program No.

Effective Date

Availability of RFU

1.09:02

D0AD5503

January 2017 production

Available

1.08:02

D2395503J

December 2016 production

Available

1.07:02

D2395503H

November 2016 production

Available

1.06:02

D2395503G

October 2016 production

Available

1.05:02

D2395503F

July 2016 production

Available

1.04:02

D2395503E

June 2016 production

Available

1.03:02

D2395503D

1st Mass production

Available

Note: Definition of Availability of RFU via @Remote

“Available”: The firmware can be updated via RFU or SD card.

“Not available”: The firmware can only be updated via SD card.

Version

Modified Points or Symptom Corrected

1.09:02

Symptom corrected:

1. Firmware update does not complete when updated via RFU.

2. The machine may stall, if it receives a succeeding job immediately after

completing a job.

3. SC374 may occur after recovery from toner end.

1.08:02

Symptom corrected:

- An abnormal sound may occur after continuously printing 20 or more pages.

- An abnormal sound may occur when the machine stops due to a waste toner

bottle full detection while printing 10 or more pages.

- If a jam occurs while the fusing temperature is relatively high, for example,

while continuously running jobs, the fusing unit attempts to prevent its

temperature from further increasing and may cause an abnormal sound or a

wrap-around jam.

- Color adjustment fails and the tone of the color may suddenly change while

printing.

- Machine may stall with an SC990, if the tray runs out of paper or a mis-feed

occurs with the last page of the job.

Other changes:

- To enable quicker first print even under low temperature and low humidity

environment, the default value of feed permit setting on C5504/MCP6004

was changed as follows:

Technical Bulletin PAGE: 2/2

Reissued: 21-Dec-16

Model: MET-C2yz

Date: 13-May-16

No.: RD244002f

Version

Modified Points or Symptom Corrected

SP1-102-011[Temp:lower:Delta:Press:Sp.1] 5->10

1.07:02

Symptom corrected:

Serial number information stored in SP5-811-001 is corrupted and the following

may not work:

- @Remote registration via external appliances

- User authentication in SDK application

1.06:02

Symptom corrected:

- Engine logs may not stored correctly if turning ON the main power or

recovering from energy saving mode with opened the front cover during

Engine OFF mode.

- Machine will stall with appeared "Scanning" and SC687 may occur if the last

page is fed and additional page is add in batch mode on SPDF.

*If SP4020-001: Dust check:ON/OFF is 0:OFF, the symptom will not occur.

Other changes:

Default value in some SPs ware changed for the following improvement.

- To improve the stuck alignment on 1 bin tray at low-temperature.

- To prevent background dirty.

1.05:02

Symptom corrected:

Output color appears different between Met-C2 and Met-C1 when printed in two-

color mode.

1.04:02

Symptom corrected:

1. SC161-02 occurs when originals are scanned from SPDF DF3100 in the

following manner:

- Scanning the first sheet in simplex and second or later in duplex.

2. Continuously running mixed size stapling jobs on Finisher SR3230 may

cause a stapling failure.

3. SC990 occurs or printing is slow when recovering from a jam or after the tray

had been loaded with paper following a tray empty status.

Specification change:

The mainframe is capable of recognizing the optional bank installed, to update

the appropriate bank firmware.

1.03:02

1st Mass production

Technical Bulletin PAGE: 1/3

Reissued: 29-Mar-17

Model: MET-C2yz

Date: 13-May-16

No.: RD244003i

RTB Reissue

The items in bold italics have been corrected or added.

Subject: Firmware Release Note: Network Support

Prepared by: M. Kumagai

From: 1st Tech Service Sect., MFP/Printer Tech Service Dept.

Classification:

Troubleshooting

Mechanical

Paper path

Part information

Electrical

Transmit/receive

Action required

Service manual revision

Retrofit information

Product Safety Other (Firmware)

Tier 2

This RTB has been issued to announce the firmware release information for the Network

Support.

Version

Program No.

Effective Date

Availability of RFU

15.61

D2395567M

May 2017 production

Available

15.60

D2395567L

January 2017 production

Available

15.59

D2395567K

December 2016 production

Available

15.58

D2395567J

November 2016 production

Available

15.57.1

D2395567H

October 2016 production

Available

15.56

D2395567G

August 2016 production

Available

15.55

D2395567F

July 2016 production

Available

15.54

D2395567E

May 2016 production

Available

15.53

D2395567D

1st Mass production

Available

Note: Definition of Availability of RFU via @Remote

“Available”: The firmware can be updated via RFU or SD card.

“Not available”: The firmware can only be updated via SD card.

Version

Modified Points or Symptom Corrected

15.61

Symptom corrected:

1. When the device is in STR mode, printing might stop and not be able to

be conducted until the device is rebooted.

2. Administrator password cannot be changed via telnet.

15.60

Other changes:

Minor bug correction.

15.59

Symptom corrected:

Minor bug correction.

15.58

Symptom corrected:

1. When the device is set to use "IEEE 802.1X" and "TLS1.2" is set to "active",

authentication will fail.

2. When the device has the USB device server option enabled and is

connected to macOS via a USB cable, the PS driver cannot be installed on

the computer. If the PS driver is already installed, printing might fail.

3. When AirPrint is set to "Disabled" in Web Image Monitor, AirPrint printing can

still be conducted via USB cable.

4. If the device has not being used a significant amount of times, functions that

require a network connection will fail.

Technical Bulletin PAGE: 2/3

Reissued: 29-Mar-17

Model: MET-C2yz

Date: 13-May-16

No.: RD244003i

Version

Modified Points or Symptom Corrected

15.57.1

Other changes:

Minor bug correction.

15.56

Other changes:

- In response to concerns regarding vulnerability, the SSL/TLS setting in the

MFP matches that in the @Remote connection.

Explanation:

The MFP connects to the @Remote center server by using the TLS 1.1 or lower-

level protocol, which is not selectable from the customer site. This specification

change allows enables the CE and the customer to select the available protocol

between the MFP and @Remote center server by changing the SSL/TLS setting

via Web Image Monitor.

Important notes:

Before updating the firmware, please check the SSL/TLS setting and allow the

following security-level for each case. Otherwise,-the @Remote service cannot

be provided:

For embedded type

- Allows TLS 1.1 or lower-level

- We need to allow TLS 1.1 or lower-level for it to function.

- We are currently preparing the TLS 1.2 connection on the @Remote center

server. The scheduled date of completion will be announced soon.

- This will change when preparation at the @Remote center server is

complete.

For RC Gate A1

- Allows TLS 1.0 or lower-level

- We need to allow TLS 1.0 or lower-level for it to function.

For RC Gate

- Allows SSL 3.0

- We need to change the certification length.

- We need to allow SSL 3.0 or lower-level for it to function.

15.55

Other changes:

1. Support for AirPrint.

This firmware is dependent on Printer firmware v1.02 (D2395570F) or later,

so please be sure to also update that firmware.

2. To avoid a window that warns about the security certificate from being

displayed when connected to Web Image Monitor, the default value of the

"Permit SSL/TLS Communication" setting has been changed from

"Ciphertext Priority" to "Ciphertext/Cleartext".

Note: Configurations will not be automatically changed when the firmware is

updated. This value will be the default in devices that have Network Support

v15.55 installed from mass production.

15.54

Symptom corrected:

An SC899 error occurs when an IC card reader that is connected via a USB

cable is unplugged from the device.

Other changes:

Technical Bulletin PAGE: 3/3

Reissued: 29-Mar-17

Model: MET-C2yz

Date: 13-May-16

No.: RD244003i

Version

Modified Points or Symptom Corrected

Support for DHCP option 60 and 77. This firmware is dependent on

System/Copy firmware v1.03 (D2395550H) or later, so please be sure to update

that firmware also.

15.53

1st Mass production

Andere Ricoh Drucker Handbücher

Ricoh

Ricoh SP 150w Gebrauchsanweisung

Ricoh

Ricoh AP410 Kurzanleitung

Ricoh

Ricoh Taurus-C1a Series Service-Handbuch

Ricoh

Ricoh Aficio AP600LU Bedienungsanleitung

Ricoh

Ricoh Pro C5300S Handbuch

Ricoh

Ricoh Aficio AP4510 Konfigurationshandbuch

Ricoh

Ricoh InfoPrint 1892 Bedienungsanleitung

Ricoh

Ricoh Pro C7100 Bedienungsanleitung

Ricoh

Ricoh SP 4520 DN Bedienungsanleitung

Ricoh

Ricoh Pro 8100S Bedienungsanleitung

Ricoh

Ricoh B121 Bedienungsanleitung

Ricoh

Ricoh Aficio MP 171 Bedienungsanleitung

Ricoh

Ricoh Aficio CL4000DN Betriebsanleitung

Ricoh

Ricoh CL7000 - Aficio D Color Laser Printer Betriebsanleitung

Ricoh

Ricoh SP C360DNW Bedienungsanleitung

Ricoh

Ricoh PRO C7200X Bedienungsanleitung

Ricoh

Ricoh AficioSP C410DN Kurzanleitung

Ricoh

Ricoh CL7200 - Aficio D Color Laser Printer Montageanleitung

Ricoh

Ricoh L5160 Installationsanleitung

Ricoh

Ricoh Pro L4130 Wartungshandbuch

Ricoh

Ricoh Aficio MP W3600 Betriebsanleitung

Ricoh

Ricoh Aficio SP 5200DN Betriebsanleitung

Ricoh

Ricoh Aficio SP C431DN-HS Bedienungsanleitung

Ricoh

Ricoh DDP 70e Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung