Ricoh Pro 8300 Series Installationsanleitung

2Throughput

CIP Training

Pro 8300 series

CIP Training Pro 8300 series

Throughput

Startup and Shutdown.

Front and left view

EAR123

1. Main power switch

To operate the machine, the main power switch must be on. If it is off, open the main power switch's cover and

turn the switch on.

2. ADF

Lower the ADF over originals placed on the exposure glass.

If you load a stack of originals in the ADF, the ADF will automatically feed the originals one by one.

3. Exposure glass

Place originals face down here.

4. Control panel

5. Toner cartridge cover

Open to change toner cartridges.

6. Front left cover

Open to remove paper jams or turn on/off the AC power switch.

7. Front right cover

Open to remove paper jams.

8. Paper trays (Trays 1–3)

Load paper here. Tray 1 is a tandem tray where paper on the left side automatically moves to the right when

paper there has run out.

An indicator on the front left side of the tray lights while paper is feeding.

9. The switch is inside the front left cover.

10. AC power switch

Press to completely turn off the power of the machine. The AC power switch must be kept on in normal use.

The switch is inside the front left cover.

•

The main power switch is on the top left of the machine. When this switch is turned on, the main power

turns on and the main power indicator on the right side of the control panel lights up. When this switch is

turned off, the main power turns off and the main power indicator on the right side of the control panel

goes out. When this is done, machine power is off.

Conﬁrm how much power the options draw, and then plug them into an outlet that is nearby but

separate from the outlet that the main machine is plugged into.

Turning On the Main Power

• This machine automatically enters Fusing Unit Off mode, Low Power mode, or Sleep mode if you

do not use it for a while.

1. Make sure the power cord is ﬁrmly plugged into the wall outlet.

2. Open the main power switch cover, and then push the main power switch.

The main power indicator goes on.

DER101

Do not push the main power switch repeatedly.

When you push the main power switch, wait at least 10 seconds after it is conﬁrmed that the main

power indicator has lit up or gone out.

If the main power indicator does not light up or go out in 5 minutes after you push the main power

switch, contact your service representative.

CIP Training Pro 8300 series

Throughput

Turning On/Off the Power

Turning Off the Main Power

• After you switch the main power on, a screen may appear to indicate that the machine is

initializing. Do not switch the power off during this process. Initialization takes about 18 minutes.

However, the time for initialization may differ depending on which options are installed on the

machine.

• If the machine does not turn on even if you press the main power switch, open the front left cover

and make sure that the AC power switch is turned on.

• Application icons appear on the [Home] screen as the applications start running.

• When disconnecting the power cord from the wall outlet, always pull the plug, not the cord.

Pulling the cord can damage the power cord. Use of damaged power cords could result in ﬁre

or electric shock.

1. Open the main power switch cover, and then push the main power switch.

The main power indicator goes out. The main power turns off automatically when the machine shuts

down. If the screen on the control panel does not disappear, contact your service representative.

Saving Energy

This machine has the following energy saving functions.

Fusing Unit Off mode

If you do not use the machine for a certain period after an operation, the machine makes a clicking

sound and enters Fusing Unit Off mode.

When the machine is in Fusing Unit Off mode, the display is on but the fusing unit heater is off to

save energy. In this mode, you can change the machine's settings on the control panel. However,

the machine must exit this mode to print.

You can change the amount of time that the machine waits before switching to Fusing Unit Off

mode under [Fusing Unit Off Mode (Energy Saving) On/Off]. For details, see "System Settings",

Device Management.

•

Do not turn off the power while the machine is in operation.

Do not hold down the main power switch while turning off the main power. Doing so forcibly turns

off the machine’s power and may damage the hard disk or memory and cause malfunctions.

To exit Fusing Unit Off mode, start print jobs.

The time required to return from Fusing Unit Off mode and resume printing is as long as the time

required for warm-up time. For details about the warm-up time.

CIP Training Pro 8300 series

Throughput

Low Power mode

• Press the [Check Status] key

Sleep mode

If you do not use the machine for a certain period after an operation, the display will turn off and

the machine goes into Low Power mode. The machine uses less electricity in Low Power mode.

You can change the amount of time that the machine waits before switching to Low Power mode

under [Low Power Mode Timer]. For details, see "System Settings", Device Management.

You can change the machine's settings to enter Low Power mode when you press the [Energy

Saver] key. For details, see "System Settings", Device Management.

To exit Low Power mode, do one of the following:

• Press the [Energy Saver] key

• Press the [Check Status] key

If the machine remains inactive for a speciﬁed period or the [Energy Saver] key is pressed, it enters

Sleep mode to further reduce the electricity it consumes. For details, see "System Settings", Device

Management.

When the machine is in Sleep mode, only the [Energy Saver] key and the [Check Status] key are

usable. The machine can print jobs from computers.

You can change the amount of time that the machine waits before switching to Sleep mode under

[Sleep Mode Timer]. For details, see "System Settings", Device Management.

To exit Sleep mode, do one of the following:

• When the machine is in Low Power mode, the [Energy Saver] key is lit. In Sleep mode, the [Energy

Saver] key ﬂashes slowly. In Fusing Unit Off mode, the [Energy Saver] key is not lit.

• The energy saving functions will not operate in the following cases:

• When ﬁxed warm-up is in progress

• When operations are suspended during printing

• When a warning message appears (The machine enters Fusing Unit Off mode unless the

cover is open.)

• When paper is jammed (The machine enters Fusing Unit Off mode except when the cover is

open.)

• When the Data In indicator is lit or ﬂashing

CIP Training Pro 8300 series

Throughput

1. Open front upper right cover.

2. Push the bottle lever at the bottom,

and then pull out the toner bottle.

3. Take the new bottle out of the box.

Turn it end on end ﬁve or six times.

4. Remove the cap (place it on the

empty bottle if replacing).

CIP Training Pro 8300 series

Throughput

Adding/Replacing Toner bottles

5. Insert NEW bottle until lever clicks.

6. Close the Toner Bottle cover.

Supply Yields

https://www.ricoh.com.au/support/my-device/recycle

Recycle: Ricoh consumable recycling

Our consumable recycling program is free to our customers as part of our goal to reach zero

waste-to-landll. Setting the industry benchmark, the program has recycled over 1,104 tonnes

of toner cartridges. The program includes a free pickup service for qualifying customers and

a Reply Paid return service.

CIP Training Pro 8300 series

Throughput

Adding/Replacing Toner bottles

Cartridge description Code Targeted yield

(prints per cartridge) Condition

Ricoh Pro 8300

print cartridge, Black 828555 82,000 Coverage 6%, A4

Note: The toner yield targets are based on the area coverage given in the table at standard conditions on uncoated A4

paper recommended for the Ricoh Pro 8300

Series. Actual yields may vary depending on individual conditions.

Removing Jammed Paper

• Some of this machine's internal components get very hot. For this reason, take care when

removing misfed paper. Not doing so could result in burns.

• Keep your hands clear of the booklet ﬁnisher tray when removing misfed paper, pulling out or

pushing in the ﬁnisher's staple unit. You can trap and injure your ﬁngers if you do not.

• When removing jammed paper, make sure not to trap or injure your ﬁngers.

• Keep your hands clear of the inside of the ring binder and the space under the ring binder tray.

You can trap your ﬁngers if you do not.

Locating jammed paper

A misfeed has occurred in the place corresponding to the letter displayed on the control panel.

Open the front cover at the location indicated by the displayed letter, and check for a paper jam. If a

lamp is lit, open the guide plate at the location indicated by the lamp, and check for a paper jam.

• When removing paper misfeeds, do not turn off the power. If you do, the conﬁgured functions and

values will be lost.

• To prevent paper misfeeds, do not leave any torn scraps of paper inside the machine.

CIP Training Pro 8300 series

Throughput

Paper path and clearing misfeeds

1. Remove the jammed paper by following the procedures that are displayed on the control

panel.

When [Previous] or [Next] is displayed, press [Next] after completing a procedure.

2. When the jammed paper is removed, restore the machine to the original state.

CIP Training Pro 8300 series

Throughput

Paper path and clearing misfeeds

Procedure for removing jammed paper

Multiple aper misfeed locations may be indicated at the same time. When this happens, check all the areas

indicated.

If there is no misfed paper in the area you check first, see the other areas that are indicated.

If coated paper frequently becomes jammed and causes "U" to appear, contact your service representative.

If a paper misfeed occurs in Rb1 - Rb5, check whether any paper has been output on top of the paper press of the

finisher shift tray. If there is paper on top of the paper press, remove the paper, and then remove the misfed

paper from inside the finisher.

When paper cannot be transferred to the post-processing side by turning the knob D1 as instructed on the screen,

see the position of the letter in the figure and turn the knob D1 in reverse direction (clockwise) to send the paper

back to the drawer unit, and then remove the paper.

After C is displayed and the drawer unit is pulled out to remove the jammed paper, check that there is no toner

searing on the location indicated in the figure. If toner smear is left, wipe off the toner with a clean and dry

cloth.

Andere Handbücher für Pro 8300 Series

Inhaltsverzeichnis

Andere Ricoh Drucker Handbücher

Ricoh

Ricoh Pro C9200 Bedienungsanleitung

Ricoh

Ricoh BRG-P1 Kurzanleitung

Ricoh

Ricoh BL-P1 Series Handbuch

Ricoh

Ricoh PE-MF4 Series Installationsanleitung

Ricoh

Ricoh Priport JP8000 Bedienungsanleitung

Ricoh

Ricoh SP3 Service-Handbuch

Ricoh

Ricoh Aficio AP2700 Bedienungsanleitung

Ricoh

Ricoh Be-C2 Installationsanleitung

Ricoh

Ricoh Ri 2000 Bedienungsanleitung

Ricoh

Ricoh D074 Series Installationsanleitung

Ricoh

Ricoh SP 200S Bedienungsanleitung

Ricoh

Ricoh Pro C9500 Einrichtungshandbuch

Ricoh

Ricoh AP505 Bedienungsanleitung

Ricoh

Ricoh Lanier LDD 030 Bedienungsanleitung

Ricoh

Ricoh Pro L4130 Montageanleitung

Ricoh

Ricoh Pro L4160 Bedienungsanleitung

Ricoh

Ricoh SP C360SNw Bedienungsanleitung

Ricoh

Ricoh Aficio SP C242DN Montageanleitung

Ricoh

Ricoh SP 110 SU Bedienungsanleitung

Ricoh

Ricoh STINGER-C1 Bedienungsanleitung

Ricoh

Ricoh B3058637 Bedienungsanleitung

Ricoh

Ricoh PRO C7200S Betriebsanleitung

Ricoh

Ricoh Aficio AP400 Bedienungsanleitung

Ricoh

Ricoh INFOPRINT 1811 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung