Ricoh Pro C9200 Installationsanleitung

1Input

CIP Training

Pro C9200 series

•

Jams and misfeeds can occur when printing on thick glossy sheets. To prevent such problems, be sure to

fan glossy sheets thoroughly before loading them.

When loading paper, set the paper direction according to its grain, as shown in the following diagram:

Tray 1

Direction of paper

grain

A3/11 × 17 tray unit,

Tray 2, or the wide LCT Multi bypass tray (Tray A)

Not recommended

CIP Training Pro C9200 series

Loading Paper

Do not stack paper over the limit mark

•Even if paper is loaded as described above, normal operations and print quality might still not

be possible, depending on the paper type.

•Prints might be noticeably curled. Flatten out prints if they are creased or curled. For details

about settings for flattening out curled paper, see "0301–0303 Correct Output Paper Curl",

Maintenance and Management.

•To prevent multiple sheets from being fed at once, fan the paper before loading it.

•If you load paper when only a few sheets of paper remain in the tray, multiple sheet feeding

may occur. Remove any remaining paper, stack them with the new sheets of paper, and then

fan the entire stack before loading it into the tray.

•Straighten curled or warped paper before loading.

•When paper in trays that are set to automatically eject unnecessary tab stock sheets runs out,

reload the tab stock from the beginning of the cycle (the first sheet).

•When you load paper into the paper tray for the first time or when you change the size or type

of paper in the paper tray, be sure to specify the appropriate paper settings in Tray Paper

Settings.

•You might at times hear a rustling noise from paper moving through the machine. This noise

does not indicate a malfunction

Loading Paper

1. Loosen the stack by rifﬂing the sheets.

CVA068

2. Holding its shorter ends, ﬂex the stack back and forth to create space between the sheets.

Repeat this several times.

CVA069

CVA070

3. Make sure there is space between the sheets.

CVA071

CIP Training Pro C9200 series

•

Check the paper edges are aligned at the left side.

When you use paper of Paper Weight 7 with a convex curl greater than 5 mm, paper of

Paper Weight 8 with a convex curl greater than 3 mm, or paper of Paper Weight 9 with

a convex curl, paper jam may occur if the height of the stacked paper is less than 4 mm.

To use paper in such condition, set the paper in the tray as follows:

•

Set as many as 5 to 10 more sheets than the number you intend to print

Correct the curl amount before setting the paper

Turn over the paper so the paper is with a concave curl.

Loading Large Capacity Trays

Loading Paper into Trays 1, 2, and the Wide Large Capacity Tray

Each paper tray is loaded in the same way.

The wide LCT is identified as Tray 3, Tray 4, Tray 5, Tray 6, Tray 7, and Tray 8.

Step: 2

Release the end fence by pressing and holding

green button. Move to back of tray.

Step: 1

Check that paper in the paper tray is not

being used, and then pull the tray carefully

out until it stops.

Remove paper if loaded.

Step: 3

gnidlohdnagnisserpybecnefedisehtesaeleR

both green buttons together. Move side

fences to maximum width of tray.

Loading Large Capacity Trays

CIP Training Pro C9200 series

Step: 4

Load paper by aligning the paper with the left

side of the paper tray.

Place paper with print side up.

Load a stack of paper about 5–10 mm high.

Make sure the paper rest on top of the

supporting plates on both sides.

Step: 5

Load additional sheets, if necessary.

Do not stack paper over the limit mark.

Step: 6

Tightly ﬁt the end fence to the loaded paper,

and then re-lock the end fence again.

Make sure there are no gaps between the

paper and end fence.

Carefully slide the paper tray fully in.

Loading Large Capacity Trays

CIP Training Pro C9200 series

2,200 sheets. (Capacity using 80 gsm uncoated paper)

Speciﬁcations.

Capacity:

Weight: Paper weight 6: 220.1 to 256.0 gsm

Paper weight 7: 256.1 to 300.0 gsm

Paper weight 8: 300.1 to 360.0 gsm

Paper weight 9: 360.1 to 470.0 gsm

Paper weight 1: 52.3 to 63.0 gsm

Paper weight 2: 63.1 to 80.0 gsm

Paper weight 3: 80.1 to 105.0 gsm

Paper weight 4: 105.1 to 163.0 gsm

Paper weight 5: 163.1 to 220.0 gsm

Type: Plain paper, Recycled paper, Uncoated papers, Coated matt and glossy

paper, Preprinted paper, Letterhead, Labels, Pre-punched paper, Tab

stock, Envelopes, Translucent paper, Textured, Transparency, and other

special and synthetic materials as defined in the Master Library.

Supporting plates

DER093

When loading small stock.

When you load paper that is 204 mm or

smaller, remove the supporting plates from

the bottom of the paper tray.

Store them in the pocket on the right-hand

side of the paper tray.

Set the paper ﬂush against the protrusions in

the bottom of the inner side fence.

Check that the scale numbers on the top of

the side fences are roughly the same.

Loading Large Capacity Trays

CIP Training Pro C9200 series

Step: 2

Attach the tab fence, and then align the end

fence gently against the paper you loaded

while pressing the release button of the end

fence.

Carefully slide the paper tray fully in.

NOTE: Replace the tab fence after use.

When loading tab stock, attach the tab fence.

Step: 1

Check that paper in the paper tray is not

being used, and then pull the tray carefully

out until it stops.

Take out the tab fence from the pocket on the

right-hand side of the paper tray.

Set the side fences to the size of the tab stock

to be loaded, and then load it.

Loading Large Capacity Trays

CIP Training Pro C9200 series

Step: 1

Set the side fences to the paper size, and

then square the paper and load it print side

up.

Do not stack paper over the limit mark.

Loading Paper into the Multi Bypass Tray (Tray A)

CIP Training Pro C9200 series

Use the multi bypass tray (Tray A) to use transparencies, translucent paper, and paper that

cannot be loaded in the paper trays.

•The maximum number of sheets you can load at the same time depends on paper type. Do not

stack paper over the limit mark. For the maximum number of sheets you can load.

•Check the paper edges are aligned at the left side.

•When loading a low number of sheets, be sure not to squeeze the side fences in too tightly. If

the side fences are squeezed too tightly against the paper, the edges may crease, the paper may

misfeed, or if it weighs between 52.3–63.0 g/m2 (14.0–16.9 lb. Bond), it may wrinkle.

DER069

Step: 2

Set the end fence.

222

DER070

1. End fence

2. Extender

Andere Handbücher für Pro C9200

Inhaltsverzeichnis

Andere Ricoh Drucker Handbücher

Ricoh

Ricoh Pro 8300S Bedienungsanleitung

Ricoh

Ricoh MET-C2yz Service-Handbuch

Ricoh

Ricoh IM 2702 Bedienungsanleitung

Ricoh

Ricoh M049 Handbuch

Ricoh

Ricoh FW770 Bedienungsanleitung

Ricoh

Ricoh Pro C900 Montage- und Bedienungsanleitung

Ricoh

Ricoh AP305 Bedienungsanleitung

Ricoh

Ricoh SP 150 Bedienungsanleitung

Ricoh

Ricoh FW830 Bedienungsanleitung

Ricoh

Ricoh MP 6503 Series Bedienungsanleitung

Ricoh

Ricoh Pro 8100S Bedienungsanleitung

Ricoh

Ricoh Pro C9200 Montageanleitung

Ricoh

Ricoh Pro C9200 Bedienungsanleitung

Ricoh

Ricoh SP C260DNw Bedienungsanleitung

Ricoh

Ricoh Aficio SP 3500SF Bedienungsanleitung

Ricoh

Ricoh Aficio BP20N Service-Handbuch

Ricoh

Ricoh Pro C9200 Bedienungsanleitung

Ricoh

Ricoh Pro C900s Originalbetriebsanleitung

Ricoh

Ricoh Aficio SP 8300DN Bedienungsanleitung

Ricoh

Ricoh Ri 2000 Bedienungsanleitung

Ricoh

Ricoh Aficio 480W Montage- und Wartungsanleitung

Ricoh

Ricoh F400 Service-Handbuch

Ricoh

Ricoh TH-C1 Service-Handbuch

Ricoh

Ricoh Aficio SP C311N Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung

IRA3D

IRA3D POETRY4 Bedienungsanleitung