Ricoh MT-P2 Bedienungsanleitung

Model MT-P2

(Machine Code G148)

SERVICE MANUAL

23 June 2006

Subject to change

Conventions Used in This Manual

This manual uses several symbols.

Symbol What It Means

Screw

Connector

E-ring

Clip ring

Clamp

Pawls (sensors)

Spring

Throughout this service manual, "SEF" denotes "Short Edge Feed" and "LEF" denotes "Long Edge Feed".

Warnings, Cautions, Notes

In this manual, the following important symbols and notations are used.

• A Warning indicates a potentially hazardous situation. Failure to obey a Warning could result in

death or serious injury.

• A Caution indicates a potentially hazardous situation. Failure to obey a Caution could result in minor

or moderate injury or damage to the machine or other property.

• Obey these guidelines to avoid problems such as misfeeds, damage to originals, loss of valuable

data and to prevent damage to the machine

• This information provides tips and advice about how to best service the machine.

Trademarks

• Microsoft®, Windows®, and MS-DOS® are registered trademarks of Microsoft Corporation in the

United States and /or other countries.

• PostScript® is a registered trademark of Adobe Systems, Incorporated.

• PCL® is a registered trademark of Hewlett-Packard Company.

• Ethernet® is a registered trademark of Xerox Corporation.

• PowerPC® is a registered trademark of International Business Machines Corporation.

• Other product names used herein are for identification purposes only and may be trademarks of their

respective companies. We disclaim any and all rights involved with those marks.

Safety Instructions

For your safety, please read this manual carefully before you service machine. Always keep this manual

handy for future reference.

Safety Information

Always obey the these safety precautions when using this product.

Switches and Symbols

Where symbols are used on or near switches on machines for Europe and other areas, the meaning of

each symbol conforms with IEC60417.

Responsibilities of the Service Technician

Maintenance

Maintenance shall be done only by trained customer engineers who have completed service training for

the machine and all optional devices designed for use with the machine.

Installation

The main machine and options can be installed by either the customer or customer engineer. The customer

or customer engineer must follow the installation instructions described in the operating instructions.

Reference Material for Maintenance

Maintenance shall be done with the special tools and the procedures prescribed for maintenance of the

machine described in the reference materials (service manuals, technical bulletins, operating instructions,

and safety guidelines for customer engineers).

• Use only consumable supplies and replacement parts designed for use with the machine.

Before Installation, Maintenance

Shipping and Moving the Machine

• Work carefully when lifting or moving the machine. If the machine is heavy, two or more customer

engineers may be required to prevent injuries (muscle strains, spinal injuries, etc.) or damage to the

machine if it is dropped or tipped over.

• Personnel moving or working around the machine should always wear proper clothing and footwear.

Never wear loose fitting clothing or accessories (neckties, loose sweaters, bracelets, etc. ) or casual

footwear (slippers, sandals, etc.) when lifting or moving the machine.

• Always unplug the power cord from the power source before you move the machine. Before you

move the machine, arrange the power cord so it will not fall under the machine.

Power

• Always turn the machine off and disconnect the power plug before doing any maintenance procedure.

After turning the machine off, power is still supplied to the main machine and other devices. To prevent

electrical shock, switch the machine off, wait for a few seconds, then unplug the machine from the

power source.

• Before you do any checks or adjustments after turning the machine off, work carefully to avoid injury.

After removing covers or opening the machine to do checks or adjustments, avoid touching electrical

components or moving parts (gears, timing belts, etc.).

• After turning the machine on with any cover removed, keep your hands away from electrical com-

ponents and moving parts. Never touch the cover of the fusing unit, gears, timing belts, etc.

Installation, Disassembly, and Adjustments

• After installation, maintenance, or adjustment, always check the operation of the machine to make

sure that it is operating normally. This ensures that all shipping materials, protective materials, wires

and tags, metal brackets, etc., (attached to protect the machine during shipping), have been removed

and that no tools remain inside the machine.

• Never use your fingers to check moving parts that are causing spurious noise. Never use your fingers

to lubricate moving parts while the machine is operating.

Special Tools

• Use only standard tools approved for machine maintenance.

• For special adjustments, use only the special tools and lubricants described in the service manual.

Using tools incorrectly, or using tools that could damage parts, could damage the machine or cause

injuries.

During Maintenance

General

• Before you begin a maintenance procedure always switch the machine off.

• Disconnect the power plug from the power source.

• Allow the machine to cool for at least 10 minutes.

• Avoid touching the components inside the machine that are labeled as hot surfaces.

Safety Devices

• Never remove any safety device (a fuse, thermistor, etc.) unless it requires replacement. Always

replace a safety device immediately.

• Never do any procedure that defeats the function of any safety device. Modification or removal of a

safety device (fuse, thermistor, etc.) could cause a fire and personal injury. After removal and re-

placement of any safety device, always test the operation of the machine to ensure that it is operating

normally and safely.

• For replacement parts use only the correct fuses, thermistors, circuit breakers, etc. rated for use with

the machine. Using replacement devices not designed for use with the machine could cause a fire

and personal injuries.

Organic Cleaners

• During preventive maintenance, never use any organic cleaners (alcohol, etc.) other than those de-

scribed in the service manual. (Refer the “2. Preventive Maintenance” in the Service Manual.)

• Make sure the room is well ventilated before using any organic cleaner. Always use organic solvents

in small amounts to avoid breathing the fumes and becoming nauseous.

• Switch the machine off, unplug it, and allow it to cool before doing preventive maintenance. To avoid

fire or explosion, never use an organic cleaner near any component that generates heat.

• Wash your hands thoroughly after cleaning parts with an organic cleaner to avoid contamination of

food, drinks, etc. which could cause illness.

Lithium Batteries

• Always replace a lithium battery on a PCB with the same type of battery prescribed for use on that

board. Replacing a lithium battery with any type other than the one prescribed for use on the board

could lead to an explosion or damage to the PCB.

• Never discard used batteries by mixing them with other trash. Remove them from the work site and

dispose of them in accordance with local laws and regulations regarding the disposal of such items.

Ozone Filters

• Always replace ozone filters as soon as their service life expires (as described in the service manual).

An excessive amount of ozone can build up around machines that use ozone filters if they are not

replaced at the prescribed time.

• The room where the machine is located must be well ventilated. Excessive ozone could cause per-

sonnel working around the machine to feel unwell.

Power Plug and Power Cord

• Before serving the machine (especially when responding to a service call), always make sure that the

power plug has been inserted completely into the power source. A partially inserted plug could lead

to heat generation (due to a power surge caused by high resistance) and cause a fire or other

problems.

• Always check the power plug and make sure that it is free of dust and lint. Clean it if necessary. A

dirty plug can generate heat which could cause a fire.

• Inspect the length of the power cord for cuts or other damage. Replace the power cord if necessary.

A frayed or otherwise damaged power cord can cause a short circuit which could lead to a fire or

personal injury from electrical shock.

• Check the length of the power cord between the machine and power supply. Make sure the power

cord is not coiled or wrapped around any object such as a table leg. Coiling the power cord can

cause excessive heat to build up and could cause a fire.

• The machine must be located near its power source. The area around must be free of obstacles so

the power cord can be disconnected quickly in case of an emergency.

• Make sure that the power cord is grounded (earthed) at the power source with the ground wire on

the plug.

• Connect the power cord directly into the power source. Never use an extension cord.

• When you disconnect the power plug from the power source, always pull on the plug, not the cable.

After Installation

Disposal of Used Items

• Ink is flammable. Never attempt to incinerate empty ink cartridges.

• Always dispose of used items in accordance with the local laws and regulations regarding the disposal

of such items.

• To protect the environment, never dispose of this product or any kind of waste from consumables at

a household waste collection point. Dispose of these items at one of our dealers or at an authorized

collection site.

Points to Confirm with Operators

At the end of installation or a service call, instruct the user about use of the machine. Emphasize the following

points.

• Show operators how to remove jammed paper and troubleshoot other minor problems by following

the procedures described in the operating instructions.

• Point out the parts inside the machine that they should never touch or attempt to remove.

• Confirm that operators know how to store and dispose of consumables such as ink cartridges, am-

monia water, paper, etc.

• Make sure that all operators have access to an operating instruction manual for the machine.

• Confirm that operators have read and understand all the safety instructions described in the operating

instructions.

• Demonstrate how to turn off the power and disconnect the power plug (by pulling the plug, not the

cord) if any of the following events occur:

1. Something has spilled into the product.

2. Service or repair of the product is necessary.

3. The product cover has been damaged.

• Caution operators about removing paper fasteners around the machine. They should never allow

paper clips, staples, or any other small metallic objects to fall into the product.

• The operator must lift the output tray to release the paper cassette before loading paper.

• Paper is loaded in the standard paper cassette without removing it from the printer.

• The operator should never attempt to remove the paper cassette from the printer.

Safety Instructions for Toner and Ink

This section describes information for users in regard to the use of toner and ink.

Accidental Physical Exposure

PPC Toner Exposure

• Work carefully when removing paper jams or replacing toner bottles or cartridges to avoid spilling

toner on clothing or the hands.

• If toner is inhaled, immediately gargle with large amounts of cold water and move to a well ventilated

location. If there are signs of irritation or other problems, seek medical attention.

• If toner gets on the skin, wash immediately with soap and cold running water.

• If toner gets into the eyes, flush the eyes with cold running water or eye wash. If there are signs of

irritation or other problems, seek medical attention.

• If toner is swallowed, drink a large amount of cold water to dilute the ingested toner. If there are signs

of any problem, seek medical attention.

• If toner spills on clothing, wash the affected area immediately with soap and cold water. Never use

hot water! Hot water can cause toner to set and permanently stain fabric.

Ink Exposure

• If ink gets on the skin, wash the affected area immediately with soap and cold running water.

• If ink gets into the eyes, immediately flush the eyes with cold running water. If there are signs of irritation

or other problems, seek medical attention.

• If ink is swallowed, drink a strong solution of cold water and table salt to induce vomiting. Seek medical

attention.

• Ink is difficult to remove from fabric. Work carefully to avoid staining clothing when performing routine

maintenance replacing ink packs or ink cartridges.

Handling and Storing Toner and Ink

Handling and Storing PPC Toner

• Toner, used toner, and developer are extremely flammable. Never store toner, developer, toner

cartridges, or toner bottles (including empty toner bottles or cartridges) in a location where they will

be exposed to high temperature or an open flame.

• Always store toner and developer supplies such as toner and developer packages, cartridges, and

bottles (including used toner and empty bottles and cartridges) out of the reach of children.

• Always store fresh toner supplies or empty bottles or cartridges in a cool, dry location that is not

exposed to direct sunlight.

Handling and Storing Ink

• Ink is flammable. Never store ink packs in a location where they will be exposed to high temperature

or an open flame.

• Always store ink packs out of the reach of children.

• Always store ink packs in a cool, dry location that is not exposed to direct sunlight.

Ink (Ink Jet)

• Ink is flammable. Never store ink cartridges in a location where they will be exposed to high tem-

perature or an open flame.

• Always store ink cartridges out of the reach of children.

• Always store ink cartridges in a cool, dry location that is not exposed to direct sunlight.

Toner and Ink Disposal

PPC Toner Disposal

• Never attempt to incinerate toner, used toner, or empty toner containers (bottles or cartridges). Burning

toner can explode and scatter, causing serious burns.

• Always wrap used toner and empty toner bottles and cartridges in plastic bags to avoid spillage.

Follow the local laws and regulations regarding the disposal of such items.

• Dispose of used toner and toner cartridges at one of our dealers or at an authorized collection site.

Always dispose of used toner cartridges and toner bottles in accordance with the local laws and

regulations regarding the disposal of such items.

Ink Disposal

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ricoh Drucker Handbücher

Ricoh

Ricoh Pro C9200 Handbuch

Ricoh

Ricoh AP410 Handbuch

Ricoh

Ricoh J012 Bedienungsanleitung

Ricoh

Ricoh SP C250SF Bedienungsanleitung

Ricoh

Ricoh 402850 Bedienungsanleitung

Ricoh

Ricoh Priport JP5000 Bedienungsanleitung

Ricoh

Ricoh Aficio 1515 Bedienungsanleitung

Ricoh

Ricoh 402434 Bedienungsanleitung

Ricoh

Ricoh Kir-P1 Service-Handbuch

Ricoh

Ricoh SP 210 Bedienungsanleitung

Ricoh

Ricoh Aficio MP C4501 Bedienungsanleitung

Ricoh

Ricoh G112 Bedienungsanleitung

Ricoh

Ricoh Pro C9500 Einrichtungshandbuch

Ricoh

Ricoh 9016 Bedienungsanleitung

Ricoh

Ricoh Lanier AP206 Bedienungsanleitung

Ricoh

Ricoh Aficio GX3050N Bedienungsanleitung

Ricoh

Ricoh PostScript3 Bedienungsanleitung

Ricoh

Ricoh InfoPrint 1612 Bedienungsanleitung

Ricoh

Ricoh Pro C9500 Montageanleitung

Ricoh

Ricoh 3245 - Type Print Server Service-Handbuch

Ricoh

Ricoh Pro C901S Stücklistenhandbuch

Ricoh

Ricoh AP1400 Bedienungsanleitung

Ricoh

Ricoh 403080 - Aficio SP 4100N-KP B/W Laser... Bedienungsanleitung

Ricoh

Ricoh Pro 1107 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung