Rikon Power Tools 10-321 Bedienungsanleitung

14” Bandsaw w/Open Stand

Owner’s Manual

For more information:

www.rikontools.com or [email protected]

For Parts or Questions:

[email protected] or 877-884-5167

Record the serial number and date of purchase

in your manual for future reference.

Serial number:

Date of purchase:

Part #10-321M1

Model: 10-321

Shown with optional Mobility Kit

Model # 13-321

Operator Safety: Required Reading

IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following

instructions must be followed at all times.

There are certain applications for which this tool was designed. We strongly recommend that this tool not be modied and/

or used for any other application other than that for which it was designed. If you have any questions about its application,

do not use the tool until you have contacted us and we have advised you.

General Safety Warnings

KNOW YOUR POWER TOOL. Read the owner’s manual carefully. Learn the tool’s applications, work

capabilities, and its specic potential hazards.

ALWAYS KEEP VISITORS AWAY FROM RUNNING MACHINES.

All visitors should be kept a safe distance from the work area.

ALWAYS MAKE THE WORKSHOP CHILDPROOF.

Childproof with padlocks, master switches, or by removing starter keys.

NEVER OPERATE A TOOL WHILE UNDER THE INFLUENCE OF DRUGS,

MEDICATION, OR ALCOHOL.

ALWAYS WEAR PROPER APPAREL.

Never wear loose clothing or jewelry that might get caught in moving parts. Rubber-soled footwear is

recommended for the best footing.

ALWAYS USE SAFETY GLASSES AND WEAR HEARING PROTECTION.

Also use a face or dust mask if the cutting operation is dusty.

NEVER OVERREACH.

Keep your proper footing and balance at all times.

ALWAYS GROUND ALL TOOLS.

If your tool is equipped with a three-pronged plug, you must plug it into a three-hole electric receptacle.

If you use an adapter to accommodate a two-pronged receptacle, you must attach the adapter plug to a

known ground. Never remove the third prong of the plug.

ALWAYS AVOID DANGEROUS ENVIRONMENTS.

Never use power tools in damp or wet locations. Keep your work area well lighted and clear of clutter.

ALWAYS REMOVE THE ADJUSTING KEYS AND WRENCHES FROM TOOLS AFTER USE.

Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before

turning it on.

ALWAYS KEEP YOUR WORK AREA CLEAN. Cluttered areas and benches invite accidents.

NEVER STAND ON TOOLS.

Serious injury could occur if the tool is tipped or if the cutting tool is accidentally

ALWAYS CHECK FOR DAMAGED PARTS.

Before initial or continual use of the tool, a guard or other part that is damaged should be checked to

assure that it will operate properly and perform its intended function. Check for alignment of moving

parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its

operation. A guard or other damaged parts should immediately be properly repaired or replaced.

ALWAYS DISCONNECT TOOLS.

Disconnect tools before servicing and when changing accessories such as blades, bits, and cutters.

ALWAYS AVOID ACCIDENTAL STARTING.

Make sure switch is in “OFF” position before plugging in cord.

NEVER LEAVE TOOLS RUNNING UNATTENDED.

1. Always allow the Bandaw blade to stop before removing scrap pieces from table.

2. Always keep hands and ngers away from the blade.

3. Never attempt to saw stock that does not have a at surface, unless a suitable support is used.

4. Always hold material rmly and feed it into the blade at a moderate speed.

5. Always turn off the machine if the material is to be backed out of an uncompleted cut.

6. Adjust the upper guide about 1/8” above the material being cut.

7. Check for proper blade size and type for thickness and type of material being cut.

8. Make sure that the blade tension and blade tracking are properly adjusted.

9. Make “relief” cuts before cutting long curves.

10. Release blade tension when the saw will not be used for a long period of time.

Special Safety Rules For Bandsaws

SAVE THESE INSTRUCTIONS.

Refer to them often.

Note: This owner’s manual is not a teaching aid. Use of this owner’s manual is intended to

show assembly, adjustments, and general use.

California Proposition 65 Warning

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains

chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.Your risk from

exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in

a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to lter out

microscopic particles.

For more detailed information about California Proposition 65 log onto rikontools.com.

13-5/8” (346 mm)

8” (204 mm)

99-3/4” (2534 mm)

1/4” – 3/4”(6-19 mm)

15-3/4” x 20-3/8” (400 mm x 518 mm)

Left-10oRight-45 o

1620/3340 ft/min

1 HP

9/4.5 A / 1700 RPM

120/240V

160 lbs

Throat Width

Max. Cutting Depth

Blade Length

Blade Width

Table Size

Table Tilt

Blade Speeds

Motor

Amps/Speed

Volts

Net weight

Safety Warnings..................................................................................................................................................2 -3

Bandsaw Safety Rules ..........................................................................................................................3

Specications ........................................................................................................................................4

Contents of Package ............................................................................................................................5

Loose Parts ...........................................................................................................................................6

Getting To Know Your Bandsaw ............................................................................................................7

Table Assembly .....................................................................................................................................8

Rip Fence Assembly .............................................................................................................................8

Hand-Wheel Assembly .........................................................................................................................8

Setting 90oTable Stop ...........................................................................................................................9

Tilting the Table .....................................................................................................................................9

Tracking Blade ......................................................................................................................................10

Adjusting Blade Tension .......................................................................................................................10

Blade Tension Indicator Adjustment.......................................................................................................10

Changing the Bandsaw Blade........................................................................................................11

Upper Blade Guide Adjustment ..........................................................................................................12

Lower Blade Guide Adjustment ..........................................................................................................12

Adjusting the Cutting Height ..................................................................................................................12

Changing Blade Speed .......................................................................................................................13

Setting Drive Belt Tension.......................................................................................................................13

Operation ............................................................................................................................................13-15

Electrical Requirements ..................................................................................................................................16

Maintenance ................................................................................................................................... ..... 17

Wiring Diagram ...................................................................................................................................17

Troubleshooting .........................................................................................................................18-19

Changing Bandsaw Tire ..................................................................................................................................19

AdjustingFence90DegreestotheTable..................................................................................................................19

Parts Diagrams/Lists ................................................................................................................................20-29

How To Guide .....................................................................................................................................30

Warranty .............................................................................................................................................31

Table of Contents

Specications

2. UNPACKING AND CHECKING CONTENTS

Model 10-321 14” Band Saw is shipped complete in one box.

A. Separate all parts from carton and check each item with Carton

Contents list below to make sure all items are accounted for, before

discarding any packing material.

B. Remove the protective oil that is applied to the table. Use any

ordinary household type grease and spot remover.

C. Apply a coat of paste wax to the table to prevent rust. Wipe all

parts thoroughly with a clean dry cloth.

ASSEMBLY

CARTON CONTENTS

Item Description Qty.

A Main Machine w/Blade Installed................................1

B Table..........................................................................1

C Package Containing Open Stand ...........................1

D Bag of Loose Parts for Main Machine........................1

E Upper Table Trunnion Assembly...............................1

F Bag of Loose Parts for Stand.................................1

G Operator’s Manual....................................................1

LIST OF LOOSE PARTS IN BAG

Item Description Qty.

1. TOOLS REQUIRED FOR ASSEMBLY

Item Description Qty.

Phillips Screwdriver................................1

Adjustable Wrench.................................1

Square...................................................1

E G

2-1/2” Dust port..........................................1

Hex Socket head cap screw M6x12..............2

Washer 6.........................................................2

Blade tension knob..........................................1

Crank handle...................................................1

Washer M6.......................................2

Hex Nut M6.....................................................2

Hex Bolt M8x45..............................................1

Hex Nut M8.....................................................1

Wing nut M6.....................................................1

Tube.................................................................1

Washer 6.........................................................1

Hex Socket head cap screw M6x45..............1

Tool holder..................................................1

Pan head screw M5x10..................................2

M3 Hex “L” wrench.........................................1

M4 Hex “L” wrench.........................................1

M5 Hex “L” wrench.........................................1

Hex Bolt, washer, nut assembly M8..................24

Hex Bolt, washer, nut assembly M6....................4

Rubber foot.........................................................4

Hex Bolt M8x16..................................................4

Lock washer 8.....................................................4

A. Open Stand Assembly

- Check contents against the parts list.

Hint: All front and side panels assemble behind (inside) leg pieces.

- Fasten front panel on to paired legs, using hex carriage bolts, washers and hex nuts. Do not fully tighten.

- Fasten side panel on to front panel and paired leg assemblies using remaining hex carriage bolts, washers and hex nuts.

- Fasten the front and side beams on the paired legs with hex carriage bolts, washers and hex nuts.

- Set stand in an upright position, ensuring that the holes on the top edge of the panels line up suf ciently to allow hex head screws to

pass through. Fully Tighten the hex carriage bolts and hex nuts.

- Press rubber feet onto the end of stand legs.

- With the aid of an assistant, lift band saw and carefully position in place on top of stand.

- Install base to stand using hex head screw (11) and washer (10) through stand and saw base, then washer (10) and hex nut (9) on top of

saw base. Repeat procedure for all four corners before tightening fully.

WARNING: To Avoid back injury, get help lifting the band saw. Bend your knees, and lift with your legs, not your back.

Parts List

Item No. Description Qty

1 Front beam 2

2 Side beam 2

3 Legs 4

4 Side panel 2

5 Front panel 2

6 Hex nut 24

7 Washer 24

8 Hex carriage bolt 24

9 Hex nut 8

10 Washer 8

11 Hex head screw 4

12 Rubber foot 4

13 Washer 4

3. INITIAL ASSEMBLY

The 10-321 band saw is supplied partly assembled. Prior to use, the following items have to be assembled: Open Stand, 2-1/2” Dust Port,

Table, Blade Tension Knob, Tool Holder, and Crank Handle.

WARNING: To avoid injury, do not attempt to run or use this machine until all parts are assembled and working properly.

B. Assemble the 2-1/2” dust port to the band saw frame with Hex

socket head cap screw and washer. Place the 2-1/2” dust port onto

the side of the band saw frame.

Locate two Hex socket head cap screws and two washers from the

bag of loose parts. Mount the dust port to the band saw frame and

install a Hex socket head cap screw with washer in each hole, then

tighten with M5 Hex “L” wrench. (See FIG. 1)

C. Assemble the upper table trunnion to the lower table trunnion with

Carriage Bolt, Glide Piece, Washer and Wing Nut (See FIG. 2).

D. Place the table onto the upper table trunnion. Carefully feed the

blade through the slot of the table. (See FIG. 2A)

FIG. 2A

FIG. 2

Band Saw Open Stand

Parts Diagram

FIG. 1

Blade Slot

Carriage Bolt

& Glide Piece

Wing Nut &

Washer

J. Place the blade tension knob onto the blade tension assembly.

(See FIG. 8)

K. The band saw has a 2-1/2” dust port and 4” dust port included for

connection to standard width shop vacuum hoses. (See Fig. 9)

It is recommended that when in use, the band saw is connected to a

suitable dust collector.

I. Assemble the tool holder to the column of the band saw with two

pan head screws. Locate two pan head screws from the bag of

loose parts. Mount the tool holder to the column and install a pan

head screw in each hole, then tighten with Phillips screwdriver.

(See FIG. 7)

H. Attach the crank handle to the belt tension crank arm with the M6

Hex nut. (See FIG. 6)

FIG. 7

FIG. 8

FIG. 9

FIG. 6

Tool Holder

G. Use the hex socket head cap screw, washer, bushing and wing

nut for correcting the working table  atness. (See FIG. 5)

FIG. 5

Blade Tension Knob

E. Locate four hex bolts and four lock washers from the bag of loose

parts used to mount the table. Mount the table to the upper table

trunnion and install a bolt with washer in each hole, then tighten with

a 13mm wrench. (See FIG. 3)

Mounting Bolts

FIG. 3

Bushing &

Wing Nut

2-1/2” Dust

Port

4” Dust

Port

F. Next locate one Hex Bolt M8x45 and one Hex Nut M8. Install un-

der the table as shown. This assembly is used to level the table.

(See FIG. 4)

FIG. 4

Underside of

Table

Table Leveling

Bolt

ADJUSTMENTS

FIG. 10

Hex Bolt (x4)

KNOW YOUR BAND SAW

1. CENTERING THE TABLE

A. Loosen the four Hex bolts mounting the table to the upper table

trunnion. (See FIG. 10)

B. Move the table sideways as required, until the saw blade runs

through the center of the table insert.

C. If the adjustment of “B” is not enough to center the table, loosen

the four  ange nuts holding the lower table trunnion and move the

table sideways to place the table in the center.

D. Re-tighten Hex bolts for trunnion; recheck the saw blade position.

2. SETTING TABLE SQUARE TO SAW BLADE ON

RIGHT AND LEFT POSITION

Loosen the wing nut on the lower table trunnion and place a suitably

sized square against the saw blade on right and left position. If the

table requires adjustment, proceed as follows:

A. Using a wrench, release the Hex nut under the table.

(See FIG. 11)

B. Place the wrench on the Hex bolt and adjust until the table is

square to the saw blade. (See FIG. 11)

C. Tighten the Hex nut and check the saw blade and the table for

square.

D. Lock the table into position and check that the indicator reads

zero degrees on the side of lower table trunnion. Loosen the screw

securing the indicator and reset if necessary to give zero degree

reading. (See FIG. 12)

Blade Tension Knob

Door Locking Knob

Blade Guides

Switch

Blade Tracking Knob

Guide Post Adjusting Knob

Motor

Upper Table Trunnion

Lower Table Trunnion

2-1/2” Dust Port

4” Dust Port

FIG. 11

Square

FIG. 12

Table Leveling

Bolt

Tool Holder

Upper Bandwheel

Door

Lower Bandwheel

Door

Drive Belt

Tension

Table Insert

Blade Tension

Indicator

Table

Table Angle

Indicator

Hex Nut

WARNING: To avoid injury from unexpected starting, whenever

changing the saw blade or carrying out adjustments, switch the

band saw off and remove the power cord from the power outlet. To

avoid injury to hands when handling the saw blade, wear gloves

whenever necessary.

A. Open the upper and lower doors by turning the door locking

knobs.

B. Loosen the blade tension by turning the blade tension knob on

the top of the upper wheel housing counterclockwise until the saw

blade has slackened (viewed from above) (See FIG. 16).

C. Remove the saw blade from the upper and lower wheels.

D. When installing the new saw blade ensure the blade teeth are

pointing downwards and towards you at the position where the saw

blade passes through the table.

E. Re-tension the new saw blade and check the saw blade tracking

by turning the upper wheel by hand. The saw blade should run in the

center of the band saw wheels.

F. If needed adjust the tracking of the saw blade; proceed as

mentioned below “ TRACKING THE BAND SAW BLADE”

G. Close the upper and lower doors by turning the door locking

knobs before reconnecting the power supply.

FIG. 16

Blade Tension Knob

7. TRACKING THE BAND SAW BLADE

Set the tracking of the saw blade before setting the blade guides.

Once the saw blade is installed and tensioned, track the saw blade

by adjusting the tracking knob by hand (See FIG. 17). The saw

blade should run in the center of the band saw wheels. Use the

blade tracking window to check position on wheel. When the correct

adjustment is achieved lock the tracking knob with the wing nut.

FIG. 17

Wing Nut

Tracking Knob

3. SETTING TABLE SQUARE BACK OF BLADE

Place a square against the back (non-tooth) side of the saw blade. If

you  nd that the table runs up hill or down hill as you feed the

work piece, proceed as follows:

A. Using a wrench, release the  ange nut on the lower table

trunnion. (See FIG. 13)

B. Place the M5 Hex “L” wrench on the Hex socket set screw and

adjust until the table is square to the saw blade on the back

(non-tooth) side of the saw blade.

C. Tighten the  ange nut and recheck the saw blade and the table

for square.

4. TILTING THE TABLE

For bevel cuts, the table tilts 0 through 45 degrees.

A. To tilt the table, loosen the wing nut on the table trunnion, set the

table to the required angle and tighten the wing nut again (See FIG.

14).

B. It is recommended to verify the correct angle setting using an

angle guide, or by making trial cuts in scrap wood. Adjust the

indicator accordingly by using a phillips head screwdriver.

FIG. 14

Wing Nut

5. ADJUSTING THE BLADE TENSION

To loosen the tension of the blade, turn the blade tension knob

counterclockwise and the tension indicator will lower. To tighten the

tension of the blade, turn the tension knob clockwise, and the

tension indicator will rise. (See FIG. 15)

6. CHANGING AND ADJUSTING THE SAW BLADE

This band saw is factory-equipped with a general-purpose wood

cutting blade, the saw blade is set prior to delivery.

To change the saw blade; the following procedure must be followed:

FIG. 13

Hex Socket Set Screw

Flange Nut

Blade Tension Knob

Tension Indicator

FIG. 15

Door Locking Knob

Tracking

Window

D. When the correct adjustment is reached, lock the roller guides in

position with the guide adjusting screws.

12. CHANGING THE BLADE SPEED

WARNING: Before changing the speed always make sure the ma-

chine has been unplugged from the electrical supply.

This band saw has two blade speeds:

A. 1620 feet/min for hardwoods, some plastics and certain nonfer-

rous metals.

B. 3340 feet/min for all other timber.

The lower bandwheel has two, integral, multi-vee form pulleys and

the motor shaft has a twin multi-vee form pulley.

The drive belt passes around the bandwheel pulley, the motor pulley

and the tension wheel. The belt tension is released and applied by

using the crank handle (See FIG. 22). This moves the tension wheel

and allows the speed to be changed.

(See DRIVE BELT POSITIONS HIGH/LOW SPEED on page 10)

The Lower Blade Guide

A. To adjust the lower blade guides,  rst position the right and left

roller guides relative to the blade by loosening the lock nut (FIG. 21)

and moving the guide carrier until both roller guides are

approximately 1/16” behind the gullets (See Inset, FIG. 19) of the

saw blade.

B. Set both roller guides to within 1/32” of the saw blade by releasing

the guide adjusting screw (FIG. 21) and moving the guide to desired

position. Lock the roller guide in position with the guide adjusting

screw. Do not set the roller guides too close as this will adversely

affect the life of the saw blade.

C. Adjust the rear roller guide to be just clear of the back of the saw

blade by unlocking the guide adjusting screw (FIG. 21) and moving

the guide to approximately 1/32” behind the blade.

8. SETTING THE CUTTING HEIGHT

A. The upper blade guide should be set as close as practical against

the work piece.

B. To adjust this height, loosen the wing nut at the side of the upper

wheel housing. (See FIG. 18)

C. Set the blade guide to the required height by turning the guide

post adjusting knob.

D. Tighten the wing nut after setting proper height.

11. ADJUSTING THE BLADE GUIDES

The Upper Blade Guide

A. To adjust the upper blade guides,  rst position the right and left

roller guides relative to the blade by loosening the lock nut (FIG. 19)

and moving the guide carrier until both roller guides are

approximately 1/16” behind the gullets of the saw blade.

B. Set both roller guides to within 1/32” of the saw blade by

releasing the guide adjusting screw (FIG. 19) on each side of the

saw blade and moving the guides to desired position. Lock the roller

guide in position with the guide adjusting screw. Do not set the roller

guides too close as this will adversely affect the life of the saw blade.

C. Adjust the rear roller guide to be just clear of the back of the saw

blade by releasing the guide adjusting screw FIG. 20 and moving the

guide to approximately 1/32” behind the blade.

D. When the correct adjustment is reached, lock the roller guide in

position with the guide adjusting screw FIG. 20.

Guide Post

Adjusting Knob

Wing Nut

FIG. 18

Guide Adjusting

Screw

Lock Nut

FIG. 19

FIG. 20

Guide Adjusting

Screw

FIG. 22

Crank Handle

Motor Pulley

Bandwheel pulley

FIG. 21

Lock Nut

Guide Adjusting

Screw

Tension Wheel

Blade Gullet

1/16”

Inhaltsverzeichnis

Sprachen:

Andere Rikon Power Tools Gesehen Handbücher

Rikon Power Tools

Rikon Power Tools 10-336 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-325 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-351 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-326 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-350 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-600VS Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-324TG Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 11-200 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-347 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-3061 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-305 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-345 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-306 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-341 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-370 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 11-600S Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-110 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-110B Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-300 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-320 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-324 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 10-622VS Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 14-700 Bedienungsanleitung

Rikon Power Tools

Rikon Power Tools 15-400 Bedienungsanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

IMET Spa

IMET Spa BASIC 300 PLUS SHI Bedienungsanleitung

IMET Spa

IMET Spa SIRIO 370 AF-E Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung