RIOTEC ILS6300DBU Bedienungsanleitung

P r o g r a mm i ng Q u i c k G u i d e

-iLS6300DBU/iLS6300DB

Connecting the Scanner

Be sure that PC is turned OFF, before Connect scanner cable to

the PC USB port on the PC as below described, Ensure that all

connections are ready, and turn on your PC.

1. Please switch ON and charge scanner for 4~5 hours at first time

before use. Scanner switch shown on Fig. 2.

2. After switch ON, the Orange LED will flash following with 3

beep-sounds. The RED LED will be OFF while it links to cradle

within Bluetooth radio range.

3. If RED LED is continual ON, please re-plug USB cable, then, scan

the 3 barcodes on the bottom of cradle sequentially. (Shown on

Fig. 3 From 1 to 3).

4. Charging issue: Cradle works as charger when putting scanner on

it. Even if the scanner's battery is full, the cradle will continue to

supply power to the scanner. We suggest you to remove scanner

from cradle when scanner is charged fully

*Note: Please install PL-2303 driver for iLS6300DB

LED Indicator Information

Orange LED ON

Full charged

Orange LED Flashing

Charging / Low battery

Red LED ON

Not read

Red LED Continual ON

Off line / out of service

Green LED ON

Good read

Remark:

*When the battery power is too low, the Orange LED will flash and beep

once. Scanner should be charged immediately.

*If scanner shuts down it is recommended to charge it fully before

turning it back on.

*Under power-saving mode, there will not be LED indication when charging.

Reset Configuration to Defaults

(scan from A1 to A7 for iLS6300DBU or B1 to B2 iLS6300DB)

iLS6300DBU

iLS6300DB

%%RSDF

%SETUP

Demo

%D%F%T

8002

%%%END

Demo

%D%F%T

*Note: Please install PL-2303 driver for iLS6300DB

Trigger Mode

Demo

%R%T%E

Trigger always

(Trigger available at any time)

Demo

%R%T%D

Trigger standard (Default)

(Trigger available, after data sent to the

device)

Transmission Speed

Transmission speed is dependent on your device. In order not to lose

data, please choose the correct speed. Middle-speed is the Default.

Demo

%B%T%H

Demo

High-speed

Ultra Slow-speed

Transmission

1transmission

Demo

Middle-speed

Ultra Slow-speed

Transmission

(Default)

2transmission

Demo

%B%T%L

Demo

Slow-speed

Ultra Slow-speed

Transmission

3transmission

Bluetooth Auto-connection

Demo

%A%L%E

Bluetooth Auto-connection ON:

When out of range, it will keep trying to

connect to device, scanner will not enter

power-saving mode.

Demo

%A%L%D

Bluetooth Auto-connection OFF:

When you are out of BT signal range, scanner

will stop sending auto-connection signal to

device after 2 minutes. During this time, it will

not enter power-saving mode.

Once you are back within range, press trigger to

connect to the device. (Default)

Keyboard Country(For USB HID only)

Scan the appropriate country code as below to program the keyboard

layout for your country or language. As a general rule, the following

characters are supported, but need special care for countries other

than the United States: @ | $ # { } [ ] = / ‘ \ < > ~

%+-$.00

%+-$.06

USA

(Original setting)

Italian

%+-$.01

%+-$.07

Norway

France

%+-$.02

%+-$.08

Germany

Vietnam

%+-$.03

%+-$.09

Sweden

Spain

%+-$.04

%+-$.10

Denmark

Portugal

%+-$.05

%+-$.11

Switzerland (F)

Hungary

%+-$.12

%+-$.18

Latin America

Icelandic

%+-$.13

%+-$.19

Brazil

Poland

%+-$.14

%+-$.20

Belgium

Turkey F

%+-$.15

%+-$.21

Bulgarian Latin

Turkey Q

%+-$.16

%+-$.22

Finland

Japan

%+-$.17

%+-$.23

Netherlands

Korea

%+-$.24

%+-$.26

Thai

Russia

%+-$.25

Switzerland German

*The different keyboard language option starts from June. 2017.

Power-saving Mode

Demo

%P%D%T00

Power-saving mode OFF

Demo

%P%D%T03

Power-saving mode ON (Default):

Enter power-saving mode after 3-minute inactivity.

This function converses battery power. When you

press "SCAN/Power ON" button, it will wake up and

begin to scan.

Demo

%P%D%T10

Power-saving mode ON:

Enter power-saving mode after 10-minute

inactivity. This function converses battery power.

When you press "SCAN/Power ON" button, it will

wake up and begin to scan.

*When charging, the scanner will not enter power-saving mode

automatically

How to append a “prefix” or a “suffix” to the

barcode data

Demo

%C%P%S

Demo

%C%S%S

prefix

suffix

1. Scan above configuration code for Prefix or Suffix

2. Enter the required values (right, numeric barcode) for Prefix or

Suffix using the hex values for the desired HEX values from “Prefix

& Suffix TABLE (blew page)”

3. Then, end by scanning Code X (below, right)

*The max. of special characters is 5.

*When you append 1~4 required values for Prefix or Suffix, it must

end with Code X

*It doesn’t need Code X, if you append 5 values to barcode data.

How to delete Prefix or Suffix

1. Scan above configuration code for Prefix or Suffix

2. Enter the “0” “0” (above, right)

3. Then end by scanning Code X (below, right)

Numeric barcode for settings

Demo

www.tec-it.com

Demo

Prefix & Suffix TABLE

HEX

HID

(SPP)

HEX

HID

(SPP)

HEX

CTRL A

(SOH)

CTRL Y

(EM)

SPACE

CTRL B

(STX)

CTRL

Z(SUB)

CTRL C

(ETX)

ESC

(ESC)

CTRL D

(EOT)

CTRL \

(FS)

;

CTRL E

(ENQ)

CTRL ]

(GS)

CTRL F

(ACK)

CTRL ^

(RS)

CTRL G

(BEL)

CTRL _

(US)

Backspace

(BS)

Tab

(HT)

(

CTRL J

(LF)

)

CTRL K

(VT)

CTRL L

(FF)

[

Enter

(CR)

CTRL N

(SO)

]

CTRL O

(SI)

CTRL P

(DLE)

CTRL Q

(DC1)

CTRL R

(DC2)

CTRL S

(DC3)

CTRL T

(DC4)

{

CTRL U

(NAK)

CTRL V

(SYN)

}

CTRL W

(ETB)

CTRL X

(CAN)

Barcode Configuration Method:

Please follow the below 1~5 steps to complete the

“Symbologies enable” or “Symbologies disable”

1. Start Configuration 2. Choose one Symbologies

3 & 4 scan 2 Enable (or Disable) setting codes

5. End Configuration

Start

Configuration

%SETUP

1D Symbologies –1

UPC-A

UPC-E

1101

1201

EAN-13

(ISBN/ISSN)

EAN-8

1301

1401

Industrial

2 of 5

Matrix

2 of 5

1701

1801

Code 93

Code 11

2101

2201

MSI/Plessey

UK/Plessey

2301

2401

1D Symbologies –2

Codabar

ISBT 128

1901

3301

UCC/EAN 128

Interleaved

2 of 5

2501

1601

Code 39

(Code 32)

GS1 DataBar

1501

2701

China Post

GS1 DataBar

Expanded

2601

2901

GS1 DataBar

Limited

2801

Enable

Disable

Enable

Disable

End

Configuration

%%%END

Quick guide is subject to change without notice.

R_180808_01

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere RIOTEC Barcode-Lesegerät Handbücher

RIOTEC

RIOTEC iLS6307JBQ Bedienungsanleitung

RIOTEC

RIOTEC iDC9507L Bedienungsanleitung

RIOTEC

RIOTEC LS6007 Bedienungsanleitung

RIOTEC

RIOTEC OM722QJ Bedienungsanleitung

RIOTEC

RIOTEC DC9277L Bedienungsanleitung

RIOTEC

RIOTEC OM7228J Bedienungsanleitung

RIOTEC

RIOTEC iDC9607AW Bedienungsanleitung

RIOTEC

RIOTEC LS6302A Bedienungsanleitung

RIOTEC

RIOTEC DC9257LP Bedienungsanleitung

RIOTEC

RIOTEC FS5100D Bedienungsanleitung

RIOTEC

RIOTEC LS6000B series Bedienungsanleitung

RIOTEC

RIOTEC CR6327A Bedienungsanleitung

RIOTEC

RIOTEC iLS6300VBU Bedienungsanleitung

RIOTEC

RIOTEC iDC9608KW Bedienungsanleitung

RIOTEC

RIOTEC iDC9508K Bedienungsanleitung

RIOTEC

RIOTEC iLS6308KBU Bedienungsanleitung

RIOTEC

RIOTEC FS5102N Bedienungsanleitung

RIOTEC

RIOTEC iDC9270J Bedienungsanleitung

RIOTEC

RIOTEC iLS6300JBU Bedienungsanleitung

RIOTEC

RIOTEC RIOSCAN iLS6302JS Bedienungsanleitung

RIOTEC

RIOTEC RIOSCAN iLS6300JS Bedienungsanleitung

RIOTEC

RIOTEC LS6300J Bedienungsanleitung

RIOTEC

RIOTEC FS5107L Bedienungsanleitung

RIOTEC

RIOTEC iLS6303ABQ Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung

RIOTEC iLS6300DBU Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken