RIOTEC ILS6303ABQ Bedienungsanleitung

P r o g ra m m in g Q u ic k G u i d e

- i LS6303AB Q/ i LS6303ABM

Connecting the Scanner

Be sure that PC is turned OFF, before Connect scanner cable to

the PC USB port on the PC as below described, Ensure that all

connections are ready, and turn on your PC.

1. Please switch ON and charge scanner for 4~5 hours at first time

before use. Scanner switch shown on Fig. 2.

2. After switch ON, the Orange LED will flash following with 3

beep-sounds. The RED LED will be OFF while it links to cradle

within Bluetooth radio range.

3. If RED LED is continual ON, please re-plug USB cable, then, scan

the 3 barcodes on the bottom of cradle sequentially. (Shown on

Fig. 3 From 1 to 3).

4. Charging issue: Cradle works as charger when putting scanner on

it. Even if the scanner's battery is full, the cradle will continue to

supply power to the scanner. We suggest you to remove scanner

from cradle when scanner is charged fully

*Note: Please install PL-2303 driver for iCR6303ABM

LED Indicator Information

Orange LED ON

Full charged

Orange LED Flashing

Charging / Low battery

Red LED ON

Offline / out of service

Green LED ON

Good read

Remark:

*When the battery power is too low, the Orange LED will flash and beep once.

Scanner should be charged immediately.

*If scanner shuts down it is recommended to charge it fully before turning it

back on.

*Under power-saving mode, there will not be LED indication when charging.

Reset Configuration to Defaults

(scan from A1 to A4 for iCR6300ABQ or B1 to B3 for iCR6300ABM)

iCR6303ABQ

iCR6303ABM

DEFALT.

BEPPWR1.

VSUFCR.

Demo

%D%F%T

Demo

%D%F%T

*Note: Please install PL-2303 driver for iCR6303ABM

Trigger Mode

Demo

%R%T%E

Trigger always

(Trigger available at any time)

Demo

%R%T%D

Trigger standard (Default)

(Trigger available, after data sent to the

device)

Transmission Speed

Transmission speed is dependent on your device. In order not to lose

data, please choose the correct speed. Middle-speed is the Default.

Demo

%B%T%H

Demo

High-speed

Ultra Slow-speed

Transmission

1transmission

Demo

Middle-speed

Ultra Slow-speed

Transmission

(Default)

2transmission

Demo

%B%T%L

Demo

Slow-speed

Ultra Slow-speed

Transmission

3transmission

Power-saving Mode

Demo

%P%D%T00

Power-saving mode OFF

Demo

%P%D%T03

Power-saving mode ON (Default):

Enter power-saving mode after 3-minute inactivity.

This function converses battery power. When you

press "SCAN/Power ON" button, it will wake up and

begin to scan.

Demo

%P%D%T10

Power-saving mode ON:

Enter power-saving mode after 10-minute

inactivity. This function converses battery power.

When you press "SCAN/Power ON" button, it will

wake up and begin to scan.

*When charging, the scanner will not enter power-saving mode

automatically

Bluetooth Auto-connection

Demo

%A%L%E

Bluetooth Auto-connection ON:

When out of range, it will keep trying to

connect to device, scanner will not enter

power-saving mode.

Demo

%A%L%D

Bluetooth Auto-connection OFF:

When you are out of BT signal range, scanner

will stop sending auto-connection signal to

device after 2 minutes. During this time, it will

not enter power-saving mode. Once you are

back within range, press trigger to connect to the

device. (Default)

How to append a “prefix” or a “suffix” to the

barcode data

Demo

%C%P%S

Demo

%C%S%S

prefix

suffix

1. Scan above configuration code for Prefix or Suffix

2. Enter the required values (right, numeric barcode) for Prefix or

Suffix using the hex values for the desired HEX values from “Prefix

& Suffix TABLE (blew page)”

3. Then, end by scanning Code X (below, right)

*The max. of special characters is 5.

*When you append 1~4 required values for Prefix or Suffix, it must

end with Code X.

*It doesn’t need Code X, if you append 5 values to barcode data.

How to delete Prefix or Suffix

1. Scan above configuration code for Prefix or Suffix

2. Enter the “0” “0” (above, right)

3. Then end by scanning Code X (below, right)

Numeric barcode for settings

Demo

www.tec-it.com

Demo

Prefix & Suffix TABLE

HEX

HID

(SPP)

HEX

HID

(SPP)

HEX

CTRL A

(SOH)

CTRL Y

(EM)

SPACE

CTRL B

(STX)

CTRL

Z(SUB)

CTRL C

(ETX)

ESC

(ESC)

CTRL D

(EOT)

CTRL \

(FS)

;

CTRL E

(ENQ)

CTRL ]

(GS)

CTRL F

(ACK)

CTRL ^

(RS)

CTRL G

(BEL)

CTRL _

(US)

Backspace

(BS)

Tab

(HT)

(

CTRL J

(LF)

)

CTRL K

(VT)

CTRL L

(FF)

[

Enter

(CR)

CTRL N

(SO)

]

CTRL O

(SI)

CTRL P

(DLE)

CTRL Q

(DC1)

CTRL R

(DC2)

CTRL S

(DC3)

CTRL T

(DC4)

{

CTRL U

(NAK)

CTRL V

(SYN)

}

CTRL W

(ETB)

CTRL X

(CAN)

1D Symbologies –1

ENABLE

CODABAR

DISABLE

~CBRENA1.

~CBRENA0.

ENABLE

Code 39

DISABLE

~C39ENA1.

~C39ENA0.

ENABLE

Code 32

DISABLE

~C39B321.

~C39B320.

ENABLE

Code 39

FULL ASCII

DISABLE

~C39ASC1.

~C39A SC 0.

ENABLE

Interleaved 25

DISABLE

~I25ENA1.

~I25ENA0.

ENABLE

Code93

DISABLE

~C93ENA1.

~C93ENA0.

ENABLE

Matrix 25

DISABLE

~X25ENA1.

~X25ENA0.

1D Symbologies –2

ENABLE

CODE 11

DISABLE

~C11ENA1.

~C11ENA0.

ENABLE

ISBT 128

DISABLE

~ISBENA1.

~ISBENA0.

ENABLE

GS1-128

DISABLE

~GS1ENA1.

~GS1ENA0.

ENABLE

TELEPEN

DISABLE

~TELENA1.

~TELENA0.

ENABLE

UPC-A

DISABLE

~UPBENA1.

~UPBENA0.

ENABLE

EAN-13

DISABLE

~E13ENA1.

~E13ENA0.

ENABLE

EAN-8

DISABLE

~EA8ENA1.

~EA8ENA0.

Quick guide is subject to change without notice.

1D Symbologies –3

ENABLE

MSI

DISABLE

~MSIENA1.

~MSIENA0.

ENABLE

GS1

Omnidirectiona

DISABLE

~RSSENA 1.

~RSSENA 0.

ENABLE

GS1 DataBar

Limited

DISABLE

~RSLENA1.

~RSLENA0.

ENABLE

GS1 DataBar

Expanded

DISABLE

~RSEENA1.

~RSEENA0.

ENABLE

CHINA POST

DISABLE

~CPCENA1.

~CPCENA0.

ENABLE

PLESSY CODEL

DISABLE

~PLSENA1.

~PLSENA0.

ENABLE

INDUSTRIAL 25

DISABLE

~R25ENA1.

~R25ENA0.

ENABLE

IATA 25

DISABLE

~A25ENA1.

~A25ENA0.

R_180903_01

Dieses Handbuch passt für folgende Modelle

Andere RIOTEC Barcode-Lesegerät Handbücher

RIOTEC

RIOTEC iLS6302J BQ Bedienungsanleitung

RIOTEC

RIOTEC DC9273A Bedienungsanleitung

RIOTEC

RIOTEC iCR6300CBQ Bedienungsanleitung

RIOTEC

RIOTEC FS5100D Bedienungsanleitung

RIOTEC

RIOTEC RIOSCAN iLS6300FS Bedienungsanleitung

RIOTEC

RIOTEC iDC9270J Bedienungsanleitung

RIOTEC

RIOTEC FS5107A Bedienungsanleitung

RIOTEC

RIOTEC iDC9607L Bedienungsanleitung

RIOTEC

RIOTEC RIOSCAN iLS6303AS Bedienungsanleitung

RIOTEC

RIOTEC iLS6307JBQ Bedienungsanleitung

RIOTEC

RIOTEC iLS6303XBU Bedienungsanleitung

RIOTEC

RIOTEC iLS6302J/KBU Bedienungsanleitung

RIOTEC

RIOTEC LS6320E Bedienungsanleitung

RIOTEC

RIOTEC DC9250KP Bedienungsanleitung

RIOTEC

RIOTEC LS6307L Bedienungsanleitung

RIOTEC

RIOTEC iLS6300JBU Bedienungsanleitung

RIOTEC

RIOTEC iDC9602N Bedienungsanleitung

RIOTEC

RIOTEC LS6303X Bedienungsanleitung

RIOTEC

RIOTEC iLS6302NBQ Bedienungsanleitung

RIOTEC

RIOTEC OM7320 Bedienungsanleitung

RIOTEC

RIOTEC LS6300E Bedienungsanleitung

RIOTEC

RIOTEC iLS6302J/KBU Bedienungsanleitung

RIOTEC

RIOTEC iLS6300JBQ Bedienungsanleitung

RIOTEC

RIOTEC iDC9507L Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung

RIOTEC iLS6303ABQ Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken