Risco RW332KPP400D Bedienungsanleitung

Panda Wireless

LCD Keypad Instructions

Models: RW332KP, RW332K

Language

Page

INTRODUCTION

The 2-Way WL Panda keypad is used to remotely program and operate the RISCO

wireless security systems. Being bi-directional, the 2-Way keypad receives a reply

status indication from the panel for each command sent to the panel. You can operate

the keypad either using a code or a proximity tag.

MAIN FEATURES

⬧Bi-directional Wireless Communication

⬧Full wireless installer programming

⬧Up to 3 Wireless keypads per system

⬧S.O.S / Two way communication emergency key

⬧Proximity tag operation

⬧Double tamper protection (Box & Wall)

⬧Battery economy mode

COMMUNICATION SETUP

The wireless Panda keypad must identify itself to the system receiver. This can be done

by typing the 11 digit serial number of the keypad into the system or using RF mode.

To set up the keypad using the serial number refer to the security system installation

manual.

Setup using RF communication:

1. Set the receiver to Learn Mode.

2. Send a Write message by pressing both keys simultaneously for at

least 2 seconds. In a voice supported system, the keypad will sound a

confirmation beep and the system will beep to acknowledge.

3. If required to change the keypad's default settings, configure the keypad's

parameters according to the system installation manual.

Note: Adding the keypad to the system can be done remotely using the configuration software

by entering the serial number of the keypad.

MOUNTING THE KEYPAD

Mount the keypad on the wall using the supplied mounting bracket.

Note: Before mounting the keypad test the keypad communication with the system.

1. Remove the fastening screw that secures the mounting bracket to the keypad (see

Figure 1).

2. Separate the mounting bracket from the keypad (see Figure 2).

3. Release battery cover from the keypad’s battery compartment (see Figure 3).

4. Attach the battery cable to the battery connector (see Figure 4), insert the batteries (while

paying attention to the polarityof the batteries) and close the battery compartment.

5. Allocate the Keypad to the Receiver (see Communication Setup).

6. Using the mounting holes as a template secure the mounting bracket to the wall

(see Figure 5).

7. Mount the keypad to the mounting bracket and insert the fastening screw to lock

the keypad (see Figures 6 and 1).













MAIN USER OPERATIONS

The following list details the user operations from the wireless Panda keypad.

User operation can be defined to be activated by a quick mode or high security mode

that requires the use of a code or proximity tag.

In the high security mode, the proximity tag can be used as a substitute for entering a

user code when the display prompts to "Insert a code".

Battery Compartment

Cover (back side)

COMMON OPERATIONS

Operation1

Quick Operation

High Security Mode2

Full Set

(Away)

Press

Press followed by code or proximity tag3

Part Set

(Stay)

Press

Press followed by code or proximity tag

Full Unset

(Disarm)

Press followed by code or proximity tag

Get System

Status

When the keypad is woken up (not in Sleep Mode) by short press of any

button (no beep sound), the keypad receives system status from the panel. A

corresponding icon indication appears on the keypad display.

1. Operations are performed by Normal press

2. Consult your installer for the operations defined with a code.

3. For optimal use of the proximity tag, use it from a distance of 1-2 cm from the top-right

corner of the keypad.

KEY OPERATION

Key

Description

Numerical keys are used to input the numeric codes that may be

required for setting, unsetting, or used to activate specific functions

In Normal Operation mode: Used to enter the User Functions menu

In User Functions menu: Used to move back one step in the menu

In Normal Operation mode: Used for Disarming (Unsetting).

In User Functions menu: Used to terminate commands and confirm

data to be stored.

Used to scroll up a list or to move the cursor to the left;

Provides the system status

Long press on provides system status with voice (in a voice

supported system)

Used to scroll down a list or to move the cursor to the right.

Changes data

ADVANCED OPERATIONS

Operation1

Quick Operation

High Security Mode

Full Setting

(Away) partition

1/2/3

Select partition

/ / and press

Select partition / /

and press followed by code

or proximity tag

Part Setting (Stay)

partition 1/2/3

Select partition / /

and press

Select partition / /

and press followed by code

or proximity tag

Fire Alarm

Pressing keys simultaneously for at least two seconds

activates a Fire alarm

Emergency /

Medical Alarm

Pressing keys simultaneously for at least two seconds

activates an Emergency alarm

Panic alarm /

Service call

Pressing + keys simultaneously for at least two seconds

activates a Panic alarm 2

Main unit Speaker

Volume 3

Press the button for 2 seconds

Select the volume level (0=No sound, 4=Full volume)

Press to save your selection

Keypad setup -

LCD contrast

, brightness

and keypad

buzzer volume

Press for 2 seconds.

Use the keys to choose from menu,

press to select, then use keys to adjust the

keypad's parameters and press

Output control

1/2/34

Press button

/ / for 2 seconds

Press button / / for

2 seconds and then enter the code

or proximity tag

Operation1

Quick Operation

High Security Mode

View Last Alarm

Press button for two seconds

System Chime

On/Off

Press the button for 2 seconds

View system

status

Short press on : LCD

display

Long press on : LCD

display + voice 3

Only LCD Dispaly: Short press

on folllowed by code

or proximity tag.

LCD display + voice: Long

press on followed by

code or proximity tag

Macro Activation5

Press / / for 2 seconds

Enter programming

mode

Press and enter the code

Changing Keypad

Language

Press simultaneously for 2 seconds. Select the

language and press to confirm.

1All operations are available while keypad is turned on (Not in Sleep Mode). All operations

are performed by Normal press (with beep), unless otherwise mentioned.

2Ask your installer for the keys definition

3In voice supported systems. Not applicable for WiComm Pro

4Ask your installer whether outputs control is applicable or not and which output is

assigned to which key

5Ask your installer for the macro defined for each key.

ICONS INDICATION

Key

Function

System is armed in Full Arm or Stay Arm mode

Off

System is disarmed

Slow Flash

System is in Exit/Entry Delay

Rapid Flash

Alarm condition

System is in Stay Arm mode (Part Set) or Zone Bypass mode

Off

No bypass zones in the system

System is ready to be armed

Key

Function

Off

System is not ready to be armed

Slow Flash

System ready to be armed while Exit/Entry zone is open

System Trouble

Off

System is operating normally

Tamper in the system

Off

No tamper in the system

System connected to cloud

Slow Flash

Cloud connectivity trouble

Off

No cloud connection configured

Proximity Tag Operation

Present the RFID (Proximity Tag) to the keypad as shown in the following illustrations:

Note: Before using the Proximity Tag, wake up the keypad by pressing any button on the keypad.

SLEEP MODE

For extending the battery life of the keypad, the keypad is designed with a Sleep mode

function. By default, 10 seconds after the last key has been pressed, the keypad will

turn off its display and LEDs. The time can be configured by your installer to a

maximum of 60 seconds.

REPLACING BATTERIES

1. Remove the fastening screw that secures the mounting bracket to the keypad

(see Figure 1).

2. Slide the keypad and remove it from the mounting bracket.

3. Remove the battery compartment cover.

4. Disconnect the battery cable from the battery connector.

5. Replace the batteries while paying attention to the polarity of the batteries.

6. Reconnect the battery cable to the battery connector.

7. Close the battery compartment cover, place the keypad back on the wall and secure

the screw to its place.

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose

of used batteries according to local regulations.

CHANGING KEYPAD PARAMETERS

Any change performed in the definition of the keypad parameters also requires

updating the keypad. This is performed by pressing the key for 2 seconds. The

panel will then send an update to the keypad.

TECHNICAL SPECIFICATION

Electrical

Battery Type

CR123, 3V Lithium battery (x 4)

RW332KPP8BTA: 3V, 10 Ah flat Lithium battery (x 1)

Current Consumption

Standby current 9µA, Max current 150 mA

Power Output

868.65MHz: 10 mW

Frequency

433.92, 868.65, 915 MHz

Modulation Type

OOK

Typical Battery Life

3 years

Low battery indication

2.6 V

Proximity RF frequency

13.56 MHz

Physical

Dimension (HxWxD)

178 x 103 x 38 mm (7 x 4.1 x 1.5“)

Weight (Including batteries)

0.435 kg

Environmental

Operating temperature

-10°C to 55°C (14°F to 131°F)

Storage temperature

-20°C to 60°C (-4°F to 140°F)

Humidity Range

Average relative humidity: 75%

Standard Compliance

EN 50131-1, EN 50131-3 Grade 2, Environmental Class

II, EN 50131-6 Type C, EN 50131-5-3

INTRODUZIONE

La tastiera Panda Radio bidirezionale è usata per programmare e utilizzare i sistemi di

sicurezza radio di RISCO Group. Essendo bidirezionale la tastiera riceve le

informazioni di stato della centrale e le risposte ad ogni comando trasmesso. La tastiera

può essere usata sia tramite codice che tramite tag di prossimità.

Verificare che la versione del sistema radio utilizzata sia compatibile con la tastiera

radio Panda.

CARATTERISTICHE PRINCIPALI

⬧Comunicazione Radio Bidirezionale

⬧Compatibile con la programmazione tecnica completa

⬧Fino a 4 tastiere per sistema

⬧Tasti di emergenza

⬧Lettore di prossimità integrato

⬧Doppia protezione tamper (Apertura e rimozione)

⬧Funzione di risparmio batteria

MEMORIZZAZIONE DELLA TASTIERA

La tastiera deve essere identificata dalla ricevente del sistema tramite l’inserimento del

numero di serie di 11 cifre o tramite procedura di auto-apprendimento via radio. Per

memorizzare la tastiera usando il numero di serie fare riferimento al manuale tecnico

del sistema radio utilizzato.

Memorizzazione tramite apprendimento radio:

4. Predisporre l’unità ricevente on modalità Memorizzazione Radio.

5. Trasmettere un messaggio WRITE premendo sulla tastiera simultaneamente i

tasti per almeno 2 secondi, sia la tastiera che la centrale emetteranno

un tono acustico di conferma.

Nota: Se il sistema supporta i messaggi vocali, la memorizzazione della tastiera verrà

confermata anche con un messaggio vocale.

6. Per modificare i parametri di default della tastiera, se necessario, fare riferimento

al manuale tecnico del sistema radio utilizzato.

Nota: La tastiera può essere memorizzata nel sistema anche usando il software di

Configurazione CS, inserendo il numero seriale della tastiera. Verificare di avere una

versione aggiornata di CS compatibile con la tastiera radio Panda.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Risco Tastenfeld Handbücher

Risco

Risco lightsys RP432KP Bedienungsanleitung

Risco

Risco RPKELW Bedienungsanleitung

Risco

Risco RPKELW Bedienungsanleitung

Risco

Risco GARDTEC 872 Bedienungsanleitung

Risco

Risco RW132KPPW3 Bedienungsanleitung

Risco

Risco lightsys RP432KPP Bedienungsanleitung

Risco

Risco EL-5829 Bedienungsanleitung

Risco

Risco ProSYS KP Bedienungsanleitung

Risco

Risco Agility 132KP Bedienungsanleitung

Risco

Risco RW132KL1 Bedienungsanleitung

Risco

Risco Panda RW332KP Bedienungsanleitung

Risco

Risco RP432KP02 Bedienungsanleitung

Risco

Risco Agility RW132KL1P Bedienungsanleitung

Risco

Risco Panda RW332K Bedienungsanleitung

Risco

Risco RPKELWP Bedienungsanleitung

Risco

Risco lightsys 2 Gebrauchsanweisung

Risco

Risco lightsys RP432KP Bedienungsanleitung

Risco

Risco RP432KPP2 Bedienungsanleitung

Risco

Risco WL Panda Bedienungsanleitung

Risco

Risco lightsys RP432KP Bedienungsanleitung

Risco

Risco RPKELW Bedienungsanleitung

Risco

Risco Agility RW132KL1P Bedienungsanleitung

Risco

Risco RPKELW Bedienungsanleitung

Risco

Risco Agility 2-way Wireless LCD Keypad Bedienungsanleitung

Beliebte Tastenfeld Handbücher anderer Marken

BFT

BFT SELETTO Bedienungsanleitung

Micro Id

Micro Id MP7G3BL Gebrauchsanweisung

WindowMaster

WindowMaster WLI 130 Bedienungsanleitung

ACT

ACT ACT PRO 1030 Bedienungsanleitung

Cardin

Cardin SSB Series Bedienungsanleitung

Harman Kardon

Harman Kardon KP 1 Bedienungsanleitung

Chamberlain

Chamberlain KPR2000 Benutzerhandbuch

CYP

CYP CR-KP1 Bedienungsanleitung

Aeware

Aeware k-35 Series Referenzhandbuch

Aritech

Aritech CS-175 Series Bedienungsanleitung

GE NetworX NX-1600E Series Bedienungsanleitung

Lenze AC Tech

Lenze AC Tech MC SERIES Bedienungsanleitung

Burg Wächter

Burg Wächter secuENTRY 7711 Bedienungsanleitung

Aeware

Aeware in.k450 Bedienungsanleitung

Lenze

Lenze EPM-H410 Bedienungsanleitung

Toshiba

Toshiba RKP007Z Bedienungsanleitung

Gemini

Gemini GEM-DXK1 KEYPAD Bedienungsanleitung

Russound

Russound MDK-C5 Betriebsanleitung