Rishabh Instruments RISH Master 3430i Bedienungsanleitung
RISH Master 3430i
RISH Master 3430i
Operating Manual
Touch Screen Digital Multi-function Meter
Installation & Operating Instructions
INDEX
Section Contents
1. Introduction
2. Measurement Reading Screens
3. Programming
3.1 Password Protection
3.2 Menu selection
3.2.1 System Parameter selection screen
3.2.2 Communication Parameter selection screen
3.2.1.1 System type
3.2.1.2 Potential transformer Primary value
3.2.1.3 Current transformer Primary value
3.2.1.4 Current transformer Secondary value
3.2.1.5 Auto Scrolling
3.2.1.6 Low current noise cutoff
3.2.1.7 Energy On Resolution
3.2.1.8 Energy digit reset count
3.2.1.9 Energy Update Rate
3.2.2.1 Address Setting
3.2.2.2 RS 485 Baud rate
3.2.2.3 RS 485 Parity selection & Stop bit Selection
3.1.1 Change Password
1
3.2.4.1 Relay 1 output selection menu
3.2.4.2 Relay 2 output selection menu
3.2.4.3 Parameter setting for Analog Output-1
3.2.4.4 Parameter setting for Analog Output-2
Relay Output
6.
5. Analog Output
3.2.5 Brightness & Contrast
4. Touch screen calibration.
3.2.6 RGB Color Code
9. Installation
9.1 EMC Installation Requirements
9.2
9.3 Wiring
9.4 Auxiliary Supply
Fusing
Earth / Ground Connections
8. Phaser Diagram
RS 485 (Modbus) output
7.
Case Dimensions and Panel Cut-out
11. Specication
10. Connection Diagrams
12. Connection for Optional Pulse output / RS 485 /Analog Ouput
Pulse output
6.1
3.2.4 Output Option selection screen (menu)
3.2.3.1 Resetting Parameter
3.2.3 Reset Parameter selection screen
9.5
9.6
2
1. Introduction
This instrument is a panel mounted 96 x 96mm DIN Quadratic Digital metering system for the
measurement of important electrical parameters like AC voltage, AC Current, Frequency,
Power, Energy(Active / Reactive / Apparent) . The instrument integrates accurate
measurement of technology (All Voltage & Current measurements are True RMS upto 15th
Harmonic) with 320x240 Pixels touch screen TFT LCD display.
This instrument can be congured and programmed at site for the following:
PT Primary, CT Primary, CT Secondary (5A or1A)
and 3 phase 3W or 3 Phase 4W system.
The front panel has a 3.5” Touch Screen through which the user can
move across the available measurement readings, reset the energy,
Min/Max (System Voltage and System Current) and congure the
product settings.
3
TABLE 1:
Measured Parameters
System Voltage
System Current
Frequency
Voltage VL1-N(4wire only)
Voltage VL2-N(4wire only)
Voltage VL3-N(4wire only)
Voltage VL1-L2
Voltage VL2-L3
Voltage VL3-L1
Current L1
Current L2
Current L3
Units of
Volts
Amps
Hz
Volts
Volts
Volts
Volts
Volts
Volts
Amps
Amps
Neutral Current ( 4 wire only )
Amps
Amps
Measurement
Active Import Energy (8 Digit resolution) kWh
kWh
Active Export Energy (8 Digit resolution)
Active Power
Reactive Power
Apparent Power
Power Factor
Phase Angle (1P2W/3P4W)
Kwatts
KVAr
KVA
Degree
kVArh
Reactive Import Energy (8 Digit resolution)
kVArh
Reactive Export Energy (8 Digit resolution)
kVAh
Apparent Energy (8 Digit resolution)
( for 3 / 4 wire)
( for 3 / 4 wire)
( for 3 / 4 wire)
( for 3 / 4 wire)
( for 3 / 4 wire)
( for 3 / 4 wire)
4
Measured Parameters Units of
Measurement
I1 THD
I2 THD
V1 THD*
V2 THD*
V3 THD*
%
I3 THD
System Voltage THD
System Current THD
%
%
%
%
%
%
%
Pictorial representation of Phasor Diagram (1P2W / 3P4W)
Pictorial representation of Voltage Waveform
Pictorial representation of Current Waveform
Pictorial representation of VA Waveform per phase(1P2W /3P4W)
*Note : THD Parameters are L-N in case of 3P 4W & L-L in case of 3P 3W .
( for 3 / 4 wire)
( for 3 / 4 wire)
( for 3 / 4 wire)
( for 3 / 4 wire)
( for 3 / 4 wire)
( for 3 / 4 wire)
2. Measurement Reading Screens
In normal operation the user is presented with one of the measurement reading screens out of
several screens. These screens from particular submenu may be scrolled through one at a time
in incremental order by touching the “ key” and in decremental order by touching “ key”
on that screen.
5
APPARENT
ENERGY
REACTIVE
EXPORT
ACTIVE
REACTIVE
EXPORT
IMPORT
ACTIVE
IMPORT
RESET
COMMUNICATION
MAIN MENU
SYSTEM
SYSTEM TYPE
PT PRIMARY
PT SECONDARY
CT PRIMARY
CT SECONDARY
AUTO SCROLL
(Sec 3.2.1.1)
(Sec 3.2.1.2)
(Sec 3.2.1.3)
(Sec 3.2.1.4)
(Sec 3.2.1.5)
(Sec 3.2.1.7)
CURRENT
VOLTAGE
SYSTEM
A
A
FREQUENCY
SYSTEM
SYSTEM
PARAMETERS
SYSTEM Max.
SYSTEM Min.
VALUES
VALUES
SYSTEM
POWER
THD.VOLTAGE
AND CURRENT
PHASE VOLTAGE
% THD
LINE CURRENT
L1 PHASE
L2 PHASE
L3 PHASE
NEUTRAL
(Sec 3.2.4)
POWER
CHANGE
(Sec 3.1)
ENERGY
AA
A
B
LINE CURRENT
% THD
LINE - NEUTRAL
LINE - LINE
VOLTAGE
VOLTAGE
WAVEFORM WAVEFORM
L3 PHASE
L2 PHASE
L1 PHASE
WAVEFORM
WAVEFORM
WAVEFORM
POWER
POWER
POWER
Parameter Screens Single Phase
PHASOR
DIAGRAM
POWER
FACTOR
CURRENT
POWER
PHASE
ANGLE
FACTOR
6
APPARENT
ENERGY
REACTIVE
EXPORT
REACTIVE
IMPORT
EXPORT
ACTIVE
ACTIVE
IMPORT
RESET
PARAMETERS
COMMUNICATION
MAIN MENU
SYSTEM
SYSTEM TYPE
NOISE CUTOFF
(Sec 3.2.1.1)
LOW CURR.
CURRENT
VOLTAGE
SYSTEM
Max. VALUES
PHASER
A
A
FREQUENCY
FACTOR
SYSTEM
SYSTEM POWER
PARAMETERS
Min. VALUES
SYSTEM
POWER
THD:VOLTAGE
& CURRENT
(Sec 3.2.2.3)
PHASE
% THD
Line Current
Neutral Current
OPTIONS
(Sec 3.2.4)
POWER
CHANGE
PASSWORD
(Sec 3.1)
ENERGY
AA
A
B
LINE CURRENT
% THD
DIAGRAM
Line - Line
VOLTAGE
Line - Neutral
VOLTAGE
NOTE: SCREENS MARKED WITH * ARE AVAILABLE
*
*
*
*
*
(Sec 3.2.2.3)
(Sec 3.2.2.3)
WAVEFORM
WAVEFORM
CURRENT
L3 PHASE
WAVEFORM *
L2 PHASE
WAVEFORM *
L1 PHASE
WAVEFORM *
POWER
POWER
FACTOR
SYSTEM
L3 PHASE
POWER *
L2 PHASE
POWER
L1 PHASE
POWER
PHASE
ANGLE *
ONLY IN 4W SYSTEM (NOT IN 3 WIRE SYSTEM)
Parameter Screens 3 Phase
SYSTEM
SYSTEM
VOLTAGE
7
Setup Parameter Screens
PULSE
OUTPUT
ENERGY
PULSE
PULSE
DURATION
RATE
ANALOG OUTPUT 1
ANALOG OUTPUT 2
selection)
(Acc. To Table 2)
(Analog 2 parameter
RS485 PARITY
PT PRIMARY
CT PRIMARY
CT SECONDARY
AUTO SCROLL
NOISE CUTOFF
LOW CURR.
RS485
BAUD RATE
RS485
ADDRESS
(Analog 1 parameter
selection)
(Acc. To Table 2)
RESET MAX VOLTAGE & CURRENT
RESET MIN VOLTAGE & CURRENT
RESET ALL
PASSWORD
(Sec 3.2.1)
PARAMETERS
PARAMETERS
COMMUNICATION
PARAMETERS
SYSTEM TYPE
BRIGHTNESS
& CONTRAST
CHANGE
PASSWORD
RESET
PARAMETERS
OPTIONS
OUTPUT
RELAY
RELAY
OUTPUT 1
OUTPUT 2
RESET ALL ENERGIES
RESOLUTION
ENERGY
RESET COUNT
UPDATE RATE
ENERGY DIGIT
ENERGY
RGB
COLOR
CODE
SYSTEM
8
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
