Robustel GoRugged R3000 Lite Benutzerhandbuch

Installation Quick Guide

R3000 Lite - Dual SIM Industrial Cellular VPN Router

Packing List

Before installing the R3000 Lite router, please verify the kit contents as following:

Robustel R3000 Lite router

Power terminal block

Documents and software CD

Optional Accessories

AC/DC power supply adapter

Rubber/magnet SMA cellular antenna for HSPA+/LTE

Serial cable (DB9 female connector switches to DB9 male connector)

35 mm DIN rail mounting kit or wall mounting kit

*If any of the above items is missing or damaged, please contact your Robustel Sales

Representative.

Environmental Requirements

Power input: 6 to 26 VDC

Power consumption: 100 mA@12 V in idle state, 400 mA (peak) @12 V in communication state

Operating temperature: -40 °C to 85 °C (R3000-L3E supports -20 °C to 75 °C )

Relative humidity: 5% to 95% RH

Hardware Introduction

As shown in the following figure, R3000 Lite router has an Ethernet port (LAN interface), a DB9

serial port (supports for RS232 and RS485), two cellular SIM card slots, two cellular antenna

interfaces and a GPS antenna interface (optional).

Dimension: 105 mm x 98 mm x 29.5 mm



Device should be in accordance

with the reliable grounding to avoid

lighting strike.

Use the rated power adapter for

the device, and note the power

polarity when wiring.

Pay attention to waterproof in

storage, transporting and operating

environment.

Place the device on the horizontal

surface.

Damaging the product’s warranty

labeling cannot enjoy the free

maintenance in warranty period.

CAUTION!

LEDs

Ethernet Port

The Ethernet port has two LED indicators. The yellow one is Link Indicator and the green one is

Speed Indicator. Each indicator has three status, for details see the table below:

Indicator

State

Description

Link Indicator

Connection is enabled

On, blinking

Data is being transmitted

Off

Connection is disabled

Speed Indicator

100 Mbps mode

Off

10 Mbps mode

Reset Button

After powering up the router, press the RST button by a small non-conductive stick with a blunt

end in about 60 seconds until all three LEDs (RUN, PPP, USR) on the left side blinking 5 times

simultaneously. Then the router will be restored to factory default settings.

Hardware Installation Steps

Step 1: After opening the package, refer to right side figure

to remove the cover, loosen the screws associated

with the cover by using a screwdriver and then find

the SIM card slot. To insert SIM card, press the card

with fingers until snap on and then tighten the

screws associated with the cover by using a

screwdriver.

Note: In order to protect the slot and SIM card,

make sure the router is power off before inserting

or removing the SIM card.

Step 2: Connect the SMA external antenna connector to the

router’s antenna interface and twist tightly. Make

sure the antenna is within the correct frequency

range.

Note: Recommended torque for mounting is 0.35 N.m

LED Name

Color

State

Description

RUN

Green

On, solid

Router is booting

On, blinking

Router is ready

Off

Router is powered off

USR

Green

On, solid/blinking

VPN tunnel/PPPoE/DynDNS is on

Off

VPN tunnel/PPPoE/DynDNS is off

PPP

Green

On, solid

PPP connection enabled

On, blinking

There is dataflow

Off

PPP connection is disabled

Polarity

Positive

Negative

GND

Debug

RS232

RS485

(2-wire)

Data+ (A)

RXD

TXD

DRXD

GND

Data- (B)

RTS

CTS

DTXD

Pinouts

Function

TX+

TX-

RX+

RX-

RSSI LEDs

Description

None

No signal or no SIM card inserted correctly

1 bar (only the first LED is on)

Signal level: 1-10 (Abnormal signal level)

2 bar (the first and the second LED are on)

Signal level: 11-20 (Average signal level)

3 bar (all the RSSI LEDs are on)

Signal level: 21-31 (Optimum signal level)

E-mail: [email protected]

Step 3: Connect the router to the site ground wire by the ground screw before powering on.

Router grounding helps prevent the noise effect due to electromagnetic interference

(EMI).

Step 4: Connect the router’s Ethernet port to a PC through a standard crossed network cable.

Step 5: R3000 Lite router supports for horizontal surface placement, DIN rail mounting and wall

mounting. For details refer to next figure.

Step 6: Use the power adapter to power on the router. R3000 Lite router supports reverse

polarity protection, but always connects to the power adapter correctly. There are two

cables associated with the power adapter. Following to the color of the head, connect

the cable marked red to the positive pole through a terminal block, and connect the

yellow one to the negative in the same way. The last step is to plug in and power on.

Two methods for mounting the router

Wall mounting

Wall mounting kit size (unit: mm)

Use 3 pcs of M3*4 countersunk phillips screws to fix the router on the wall mounting kit,

and then use 2 pcs of M3 drywall screws to mount the router associated with the wall

mounting kit on the wall.

Note: Recommended torque for mounting is 1.0 N.m, and the maximum allowed is 1.2 N.m.

DIN rail mounting

DIN rail size (unit: mm)

Use 3 pcs of M3*4 countersunk phillips screws to fix the router on the DIN rail, and then

hang the DIN rail on the bracket. It is necessary to choose the standard bracket.

Note: Recommended torque for mounting is 1.0 N.m, and the maximum allowed is 1.2 N.m.

Andere Handbücher für GoRugged R3000 Lite

Inhaltsverzeichnis

Andere Robustel Netzwerk-Router Handbücher

Robustel

Robustel GoRugged R3000 Lite Bedienungsanleitung

Robustel

Robustel GoRugged R3000 Lite Bedienungs- und Wartungsanleitung

Robustel

Robustel GoRugged R2000 Bedienungsanleitung

Robustel

Robustel GoRugged R3000 Lite Bedienungsanleitung

Robustel

Robustel R3000-3P Bedienungsanleitung

Robustel

Robustel GoRugged R2000 Bedienungsanleitung

Robustel

Robustel R3000-Q3PA Bedienungsanleitung

Robustel

Robustel R1520 Bedienungsanleitung

Robustel

Robustel R5020 Bedienungsanleitung

Robustel

Robustel GoRugged R3000-3P-GPS Bedienungsanleitung

Robustel

Robustel GoRugged R2000 Handbuch

Robustel

Robustel GoRugged R3000 Lite Bedienungsanleitung

Robustel

Robustel R3000-3P Bedienungsanleitung

Robustel

Robustel EV8100 Bedienungsanleitung

Robustel

Robustel GoRugged R2000 Bedienungsanleitung

Robustel

Robustel GoRugged R2000 Bedienungsanleitung

Robustel

Robustel GoRugged R3000 Lite Bedienungsanleitung

Robustel

Robustel GoRuggedR 3000 Bedienungsanleitung

Robustel

Robustel R1511 Bedienungsanleitung

Robustel

Robustel EG5200 Bedienungsanleitung

Robustel

Robustel GoRugged R3000 Lite Bedienungsanleitung

Robustel

Robustel GoRugged R3000 Lite Bedienungsanleitung

Robustel

Robustel GoRugged R2000 Bedienungsanleitung

Robustel

Robustel GoRugged R3000 Lite Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise