Rockwell Automation Allen-Bradley 6300V-RVLDV-RX Bedienungsanleitung

Installation Instructions

Original Instructions

Remote Video Link Receiver for 6300B Box PCs and 6300T Box Thin Clients

Catalog Number 6300V-RVLDV-RX, 6300V-RVLDV-RXTX

Product Overview

Your remote video link (RVL) receiver provides long-distance video connection up to 100 m (328 ft) in one of two ways.

• Industrial Monitor > RVL Receiver > Industrial PC with Integrated Transmitter

• Industrial Monitor > RVL Receiver > RVL Transmitter > Industrial PC

UL/cUL Mark Compliance

Equipment with the UL/cUL mark complies with the requirements of UL 61010-1, UL 61010-2-201, CSA C22.2 No. 61010-1, and CSA C22.2 No. 61010-2-201. A copy of the

certificate of compliance is available at rok.auto/certifications.

Topic Page

Product Overview 1

UL/cUL Mark Compliance 1

European Union Directive and UKCA Compliance 2

Unpack your RVL Receiver 2

Installation Site Guidelines 2

Mount your RVL Receiver 4

Connect your RVL Receiver 5

Additional Resources 8

ATTENTION: Read this document and the documents that are listed in the Additional Resources section about installation, configuration, and

operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with

installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.

Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by

suitably trained personnel in accordance with applicable code of practice. If this equipment is used in a manner that is not specified by the

manufacturer, the protection that is provided by the equipment may be impaired.

ATTENTION: This equipment is suitable for use in Class I, Division 2, Groups A, B, C, and D hazardous locations or non-hazardous locations only. 

This equipment is considered open equipment, which means it must be mounted in an enclosure where the equipment can be operated from the front

panel. The enclosure in which this equipment is installed must be accessed only with a key or tool, and only by trained and authorized personnel.

Industrial Monitor

RVL Receiver

6300V-RVLDV-RX

RVL Cable

100 m (328 ft) Maximum Length

USB 2.0 Cable

Industrial PC

with Integrated Transmitter

DVI Cable

Industrial Monitor RVL Receiver

6300V-RVLDV-RX

RVL Cable

100 m (328 ft) Maximum Length

RVL Transmitter

6300V-RVLDV-TX Industrial PC

USB 2.0 Cable

DVI Cable

USB 2.0 Cable

DVI Cable

2Rockwell Automation Publication 6300V-IN004A-EN-P - November 2022

Remote Video Link Receiver for 6300B Box PCs and 6300T Box Thin Clients Installation Instructions

European Union Directive and UKCA Compliance

This equipment meets the European Union Directive and UK requirements when installed within the European Union or EEA regions and have the CE marking. A copy of the

declaration of the conformity is available at rok.auto/certifications.

Unpack your RVL Receiver

Your RVL receiver ships with the following items:

• RVL receiver, 6300V-RVLDV-RX

• DC terminal block kit

•Mountingkits

- Book mount kit: bracket (quantity 1) and screws (quantity 2)

- Wall mount kit: brackets (quantity 2) and screws (quantity 4)

- DIN rail mount kit: rail hook (quantity 1) and screws (quantity 2)

Installation Site Guidelines

Follow these installation site guidelines to make sure that your RVL receiver provides service with excellent reliability.

• When choosing the installation site, consider the following:

- The site must have sufficient power.

- The site must be indoors your RVL receiver to direct sunlight.

• The maximum operating ambient temperature of your RVL receiver is 50 °C (122 °F).

- Measure the ambient temperature 5 cm (2 in.) away from all cooling openings.

- Make sure all cooling openings/grids are not obstructed to confirm proper airflow.

- Your RVL receiver can be stored in a surrounding air temperature range of -5…+60 °C (23…140 °F).

- The relative humidity (RH) of the ambient air must be 80% non-condensing when your RVL receiver is operating or being stored.

• When planning the layout and connections of your RVL receiver:

- For electromagnetic compatibility (EMC), place the cables away from the source(s) of electric noise (such as power cables, high-voltage power sources,

transformers, electric welders, or radio frequency (RF) sources) that could compromise the quality of the signal.

- Do not place the RVL cable together with power cables unless an adequate insulation class is provided.

- The chassis of your RVL receiver must be connected to ground via the ground screw.

- Consider the placement of required components and the maximum length of the cables to connect your RVL receiver to other components. See Required

Equipment.

Required Equipment

To complete the installation of your RVL receiver, the following equipment is required.

ATTENTION: This equipment is intended to operate in an industrial or control room environment, which uses some form of power isolation from the

public low-voltage mains. Some computer configurations cannot comply with the EN 61000-3-2 Harmonic Emissions standard as specified by the EMC

Directive of the European Union. All I/O cables must be used only indoors.

Before you unpack your RVL receiver, inspect the shipping carton for damage. If damage is visible, immediately contact the shipper and request assistance.

If there is no visible damage, proceed with unpacking.

WARNING: This RVL receiver is:

• suitable for use in CLASS I, DIVISION 2, GROUPS A, B, and D Hazardous Locations or Non-hazardous Locations only.

• considered open equipment which means that it may only be integrated in housings or cabinets where the front panel can be accessed for operation.

Components Cables Tools

• Industrial monitor

• Industrial PC with integrated transmitter or RVL transmitter

(6300V-RVLDV-TX) and Industrial PC

• DIN Rail (for DIN rail-mount installation only)

• 24V DC (input voltage 18…32V DC) power supply (1)

(1) The power supply must: (a) satisfy the requirements of a safe extra low voltage (SELV) in accordance with IEC/EN/DIN EN/UL60950-1 and (b) fulfill the requirements NEC Class 2 LPS in accordance with

IEC/EN/DIN EN/UL60950-1. Connect the system with a cable cross-section of 0.75 • 1.5 mm2(from AWG18 to AWG16 suitable in a minimum of 75 °C (167 °F).

• DVI cable, 11 m (36 ft) maximum length (2)

• USB 2.0 cable, 11 m (36 ft) maximum length (2)

• RVL (Cat. 5E/Cat. 6 A connection) cable, 100 m (328 ft)

maximum length, quantity 1

(2) Two cables are required if your installation requires a separate RVL transmitter (6300V-RVLDV-TX).

For wall mount, shelf mount, or DIN rail attachment:

• Drill and 4 mm drill bit

• #2 Phillips screwdriver

• M4x20 stainless steel screws, quantity 4

For DC power connector assembly and ground wire installation:

•2.5mmhexscrewdriver

• Wire stripper, cutter, and crimper tool

•Cuttingpliers

• Safety glasses

Rockwell Automation Publication 6300V-IN004A-EN-P - November 2022 3

Remote Video Link Receiver for 6300B Box PCs and 6300T Box Thin Clients Installation Instructions

Approximate Dimensions

Figure 1 - Approximate Dimensions with Mounting Kit [cm (in.)]

2.00

(0.79)

15.20

(5.98)

0.60

(0.24)

0.85

(0.33)

16.70

(6.57)

Ø 0.90

(0.35)

Ø 0.45

(0.18)

0.60

(0.24)

0.45

(0.18)

1.65

(0.65)

3.30

(1.30)

19.20

(7.56)

9.80

(3.70)

2.00

(0.79)

15.20

(5.98)

17.70

(6.97)

3.38

(1.33)

16.50

(6.50)

0.60

(0.24)

0.60

(0.24)

3.60

(1.42)

9.40

(3.70)

Ø0.45

(1.78)

Ø0.90

(0.35)

2.30

(0.91)

2.30

(0.91)

1.34

(0.53)

3.30

(1.30)

4.64

(1.83)

6.40

(2.52)

6.40

(2.52)

3.30

(1.30)

2.40

(0.94)

1.50

(0.59)

6.85

(2.70)

9.40

(3.70)

4.75

(1.87)

4.65

(1.83)

6.85

(2.70)

15.2

(5.98)

0.90

(0.35)

1.50

(0.59)

0.90

(0.35)

7.60

(2.99)

9.40

(3.70)

10.74

(4.23)

15.20

(5.98)

3.30

(1.30)

1.34

(0.53)

7.60

(2.99)

View of Unit from Front

View of Unit from Top

Wall Mount InstallationBook Mount Installation

DIN Rail Bottom Mount Installation DIN Rail Back Mount Installation

View of Unit from Front

View of Unit from Top

View of Unit from Bottom

View of Unit from Front

View of Unit from Side

View of Unit from Front View of Unit from Top View of Unit from Back

View of Unit from Side

4Rockwell Automation Publication 6300V-IN004A-EN-P - November 2022

Remote Video Link Receiver for 6300B Box PCs and 6300T Box Thin Clients Installation Instructions

Mount your RVL Receiver

Attach the Bracket Kit

A book mount bracket kit, wall mount bracket kit, and a DIN rail mount kit for bottom mount or back mount installation is supplied with your RVL receiver.

Figure 2 - Mounting Bracket Kits and Attachment

1. See Figure 2 to identify the correct mounting holes for your selected mounting kit.

2. Using a 2.5 mm hex screwdriver, hand tighten the screws (supplied) to secure the bracket(s) or DIN rail hook to your RVL receiver.

Secure your RVL receiver

3. Check that your RVL receiver is level and square.

4. Mark and drill pilot holes in the wall or shelf.

5. For book mount or wall mount installation: Insert the M4x20 mounting screws (not provided) through the mounting holes of the bracket and into the pilot holes on

the wall or shelf, then tighten the mounting screws.

For DIN rail bottom mount or DIN rail back mount installation: Attach the DIN rail hook to the DIN rail (not provided).

IMPORTANT If you will be installing your RVL receiver in an environment where vibration is present, your RVL receiver must be secured to a shelf, wall, or DIN rail

using one of the three mounting kits provided. If vibration is not present and you will not be mounting your RVL receiver to a wall, shelf, or DIN rail,

proceed to Connect your RVL Receiver on page 5.

Bracket

Attachment

Wall Mount Bracket Installation

Screws

Hook

Attachment

DIN Rail Hook Installation

Book Mount Bracket Installation

Screws

Hook Attachment

DIN Rail

Hook

Bracket

View of Unit from BottomView of Unit from Side

Bracket

Attachment

Bracket

Attachment

View of Unit from Bottom

DIN Rail Hook

Profile

View of Unit from Back

DIN Rail

Hook

DIN Rail Hook

Profile

View of Unit from Top

View of Unit from Side

DIN Rail Back Mount

DIN Rail Bottom Mount

ScrewsScrews Screws

Rockwell Automation Publication 6300V-IN004A-EN-P - November 2022 5

Remote Video Link Receiver for 6300B Box PCs and 6300T Box Thin Clients Installation Instructions

Connect your RVL Receiver

The following table identifies the status indicators and input/output (I/O) ports on the front of your RVL receiver.

Assemble the DC Terminal Block Kit

The connector assembly provides strain relief for the DC power wires by reducing their movement. To assemble and attach the DC terminal block kit:

DC Power Conn ector Assembly S teps

Figure 3 - DC Terminal Block Assembly Steps

1. Open the DC terminal block (supplied) (A in Figure 3).

2. Insert the cable tie through the slots of the appropriate connector clamp (B in Figure 3).

3. Strip the end of each DC power wire to the length in Table 2.

4. Insert each stripped end into the DC terminal block as shown in Table 2.

5. Tighten the screws on top of the DC terminal block to secure the DC power wires to the torque value in Table 2.

6. Slide the connector half with the attached cable tie onto the end of the DC terminal block (C in Figure 3).

7. Tighten the cable tie so it is snug against the terminal wires.

8. Use cutting pliers to cut the excess cable tie (D in Figure 3).

9. Install the white label supplied with the kit (E in Figure 3).

Table 1 - RVL Receiver I/O Port Locations and Ground Screw

Note No. Component/Cable Type

1 RVL In

2 DVI-D Output

3USB 2.0 (1)

(1) The USB ports are not for use in hazardous locations. Only use the USB ports for initial setup and maintenance.

424VDCPower

5Ground Screw

• Your DC powered RVL receiver requires a safety extra low voltage (SELV) power supply. The internal power supply is protected against reverse polarity.

• To minimize ground loop currents and noise, we recommend that your DC powered RVL receiver uses only one grounded connection. 

See Install the Ground Wire on page 6 for the ground connection on these models.

IMPORTANT The DC terminal block in the photos is only for illustrative purposes. Your DC terminal block can differ in size, shape, and color to what is shown

in the photos.

Table 2 - DC Terminal Block Connection Specifications

Note No. Description Attribute

1 DC+ (24V DC nominal) recommended power wire size 1.5 mm2

(16 AWG)

2 DC- (0V DC) recommended power wire size 1.5 mm2

(16 AWG)

3 Stripped wire length 7 mm

(0.275 in.)

4 Torque range to secure DC power wires 0.22...0.25 N•m

(0.16...0.18 lb•ft)

5 Torque value to reinstall DC terminal block to computer 0.3 N•m

(0.22 lb•ft)

IMPORTANT DC power wires must be of stranded copper and sized according to Table 2

The white label can be used for identification or other information.

LINK

RUN

PWR

VIDEO

View of Unit from Front

DA B C E

Ground

Screw

6Rockwell Automation Publication 6300V-IN004A-EN-P - November 2022

Remote Video Link Receiver for 6300B Box PCs and 6300T Box Thin Clients Installation Instructions

10. Align and install the other connector clamp half to complete the assembly (F in Figure 3).

11. Reconnect the DC terminal block with the connector assembly to your RVL receiver (G in Figure 3 on page 5).

12. Torque the DC terminal block flange screws to the values in Table 2 on page 5.

13. Turn on the main power switch or breaker.

14. Tighten the screws on top of the DC terminal block to secure the DC power wires to the torque value in Table 2 on page 5.

Install the Ground Wire

1. Be sure that the main power switch or breaker is still turned off.

2. Remove the supplied nut, eyelet terminal, and washers from the ground screw on the side of your RVL receiver. See Table 1 on page 5 for the ground screw location.

3. Attach a 2.50 mm2(14 AWG) or larger external wire to the eyelet terminal.

4. Strip 5.00 mm (0.20 in.) from the covering at the end of the grounding wire.

5. Insert the stripped end of the grounding wire into the open end of the eyelet terminal, and crimp it securely to the wire.

6. Install the ground wire and washers to the ground screw in the following sequence:

7. Reinstall the ground screw to the chassis of your RVL transmitter.

When installed correctly, both tabs of the clamp half lock into place.

SHOCK HAZARD: The chassis of your RVL receiver must be connected to ground via the ground screw.

Use a grounding wire with an insulation color that is approved by your local inspection authority.

Note No. Description

1Toothedwasher

2Eyeletterminal

3Washer

4Lockwasher

5 Ground screw

We recommend that the computer circuit be supplied with its own disconnect.

Use an uninterruptible power supply (UPS) to help protect against unexpected power failure or power surges.

1 42 3 5

Rockwell Automation Publication 6300V-IN004A-EN-P - November 2022 7

Remote Video Link Receiver for 6300B Box PCs and 6300T Box Thin Clients Installation Instructions

Attach the I/O Cables and Power Cords

Figure 4 - I/O Cable Connection

1. Attach the RVL cable, DVI-D Output, and USB 2.0 cable to the I/O ports at the front of your RCL receiver. See Table 1 on page 5 to identify I/O port locations.

2. Connect the free end of the I/O cables and power cords to your hardware as shown in Figure 4.

3. Connect the free end of the power cords to your wall outlet.

Once power is supplied to your RVL receiver and other hardware, light-emitting diode (LED) status indicators will illuminate.

Table 3 - LED Status Indicators

Note No. Description

1VideoLink

2 Link

3Run

4Power

DVI-D USB 24V DC

RVL IN USB USB

DVI-D OUT

POWER

24V DC

RVL OUT USB

DVI-D IN

POWER

24V DC

DVI-D OUT

24V DC

RVL OUT

DVI-D USB 24V DC

RVL IN USB USB

DVI-D OUT

POWER

24V DC

Industrial Monitor > RVL Receiver > Industrial PC with Integrated Transmitter

RVL (Cat. 5E/Cat. 6 A connection) cable, 100 m (328 ft) maximum length

USB 2.0 cable

DVI cable

Industrial Monitor > RVL Receiver > RVL Transmitter > Industrial PC

RVL (Cat. 5E/Cat. 6 A connection) cable, 100 m (328 ft) maximum length

Industrial Monitor

RVL Receiver

Industrial PC

RVL Transmitter

Industrial PC with Integrated Transmitter

Industrial Monitor

RVL Receiver

DVI cable

USB 2.0 cable

Ground

Specified

Input Power

24V DC

Ground

DVI cable

USB 2.0 cable

24V DC

LINK

RUN

PWR

VIDEO

View of Unit from Front

Publication 6300V-IN004A-EN-P - November 2022

Rockwell Otomasyon Ticaret A.Ş. Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400 EEE Yönetmeliğine Uygundur

DIR 10007071030 (Version 00)

Vendor Code: 80460112.00

Allen-Bradley, expanding human possibility, and Rockwell Automation are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

*PN-685685*

PN-685685

Your comments help us serve your documentation needs better. If you have any suggestions on how to improve our content, complete the form at rok.auto/docfeedback.

For technical support, visit rok.auto/support.

Waste Electrical and Electronic Equipment (WEEE)

Rockwell Automation maintains current product environmental compliance information on its website at rok.auto/pec.

At the end of life, this equipment should be collected separately from any unsorted municipal waste.

Additional Resources

This publication provides basic installation instructions. For more information, see the following Rockwell Automation publications at https://rok.auto/literature.

Resource Description

6300B Box PC and 6300T Thin Clients User Manual, publication 6300B-UM001 Provides details on how to configure, operate, and troubleshoot the 6300B book mount box

PCs and 6300T book mount box thin clients.

6300 Industrial Computer and Monitor Specifications Technical Data, publication 6300-TD001 Provides technical specifications for 6300 industrial computers and monitors.

6300V RVL Receiver User Manual, publication 6300V-UM004 Provides detail on how to configure, operate, and troubleshoot the 6300V RVL receiver.

Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1 Provides general guidelines to install a Rockwell Automation industrial system.