Romik 1434 Bedienungsanleitung

REV 1 04/15/20

Installation Instructions

Part No. 1434

Product: Running Boards

Application:

Buick Enclave 2018+

Chev Traverse 2018+

Level of Difficulty: 1

2 3 4 5

Installation Time: 60 min

Hardware

Torque Specifications

M6 Bolt

3 ft-lbs.

M8 Bolt

7 ft-lbs.

M10 Bolt

16 ft-lbs.

M12 Bolt

28 ft-lbs.

ATTENTION: Use correct torque settings to avoid

damaging the running boards and or mounting

brackets. Failure to do so will void your warranty.

If you have any questions please contact our technical

team at 1-866-717-6645

Installation Instructions 1434 Bracket Kit

NOTE: Due to the body design on this vehicle there is a visible gap. Please review images on

www.Romik.com before installing.

Step 1: Locate front mounting locations and hardware as per 1st page of this installation manual

Step 2: Install provided HTC 263 as shown on Figure 1. Remove factory rubber plug as shown on Figure 2

Install provided HTC 243 as shown Figure 3.

Step 3: Install front bracket Figure 4. Do not tighten

Step 4: Locate middle bracket position, Install provided HTC 311 as shown Figure 5, Remove factory rubber

plug as shown Figure 6. Install provided HTC 243 Figure 7.

Step 5: Install middle bracket Figure 8. Do not tighten

Video

Installation

Instruction:

Figure 1

HTC 263

Figure 2

Figure 3

Figure 4

Figure 5

HTC 311

HTC 243

HTC 243

Figure 6

Figure 7

Figure 8

Installation Instructions 1434 Bracket Kit

Step 6: Locate rear bracket position Figure 8, Install provided HTC 284. Remove factory rubber plug Figure 9

and install proviced HTC 243 Figure 10.

Step 7: Install rear bracket as show Figure 11 and 12 Do not tighten

Step 8: Proceed to last page of this manual for running board install instructions and torque values

For Technical support please call our team at 1-866-717-6645 and one of our experts will assist

you with this installation.

Thank you for choosing Romik.

Figure 8

Figure 9

Figure 10

Figure 11

Figure 12

HTC 284

HTC 243

Running Board Installation Instructions

1) Flip your Romik running boards onto a flat surface, make sure to place the running boards on a

towel or cardboard in order to protect the surface Figure 1.

2) Loosen the M8 bolts on back of your running boards Figure 2. Depending on your model there

Will be either 6 or 8 bolts installed per side.

3) Once your brackets have been installed, place the running board onto the brackets as shown on

Figure 3.

4) Adjust running boards, centering on vehicle. Hand tight M8 hardware on running boards.

5) Follow the torque procedures, torque M8 hardware to 7 ft-lbs using a torque wrench.

6) Cleaning and maintaining your running boards is important, apply a light coat of a quality

carnauba wax at least 2X per year. Wash often with mild soap and make sure to remove all soap

Residue. Many car automatic carwashes use a strong soap, make sure to use enough water to

remove all residue.

7) Register your products at www.Romik.com/contact/productregistration

8) Warranty information at www.Romik.com/warranty

Inhaltsverzeichnis

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung