Rosemount 8714D Bedienungsanleitung
www.rosemount.com
Quick Installation Guide
00825-0100-4764, Rev BA
June 2004 Rosemount 8714D
¢00825-0100-4764W¤
Start
Step 1: Change Transmitter Parameters
Step 2: Connect the Rosemount 8714D
Step 3: Perform Electronics Trim
Step 4: Verify 8714D Calibration Standard
Magnetic Flowmeter Simulator
4764_revBA_QIG.fm Page 1 Tuesday, June 22, 2004 1:49 PM
Quick Installation Guide
00825-0100-4764, Rev BA
June 2004
Rosemount 8714D
2
© 2004 Rosemount Inc. All rights reserved. All marks property of owner.
Electronics Trim of an 8712D, 8732C, or 8742C
Magnetic Flowmeter Transmitter
The Rosemount 8714D is a high-precision instrument that supplies a 8712D, 8732C, or
8742C Magnetic Flowmeter Transmitter with a voltage corresponding exactly to 0.00 ft/s,
3.00 ft/s, 10.00 ft/s, and 30.00 ft/s. The precise 30.00 ft/s voltage signal may be used to
recalibrate or verify operation of the transmitter. (This same procedure is used by the factory
to calibrate the transmitter; it is rarely needed by customers.)
Perform this procedure only if you believe that transmitter is no longer accurate.
IMPORTANT NOTICE
This installation guide provides basic guidelines for the Rosemount®8714D. It does not
provide instructions for detailed configuration, diagnostics, maintenance, service,
troubleshooting. The manual and this QIG are also available electronically on
www.rosemount.com.
WARNING
Explosions could result in death or serious injury:
In an Explosion-proof/Flame-proof installation, do not remove the transmitter covers
when power is applied to the unit.
Electrical shock can result in death or serious injury
• Avoid contact with the leads and terminals. High voltage that may be present on leads
can cause electrical shock.
Rosemount Inc.
8200 Market Boulevard
Chanhassen, MN USA
55317
T (US) (800) 999-9307
T (Intnl) (952) 906-8888
F (952) 949-7001
Emerson Process Management
Flow
Groeneveldselaan 6-8
3903 AZ Veenendaal
The Netherlands
T 31 (0) 318 549 549
F 31 (0) 318 549 559
Emerson Process Management
Asia Pacific Private Limited
1 Pandan Crescent
Singapore 128461
T (65) 6777 8211
F (65) 6777 0947/65 6777 0743
4764_revBA_QIG.fm Page 2 Tuesday, June 22, 2004 1:49 PM
Quick Installation Guide
00825-0100-4764, Rev BA
June 2004 Rosemount 8714D
3
STEP 1: CHANGE TRANSMITTER PARAMETERS
1. Use the HART Communicator or Local Operator Interface (LOI) to change the
parameters of the transmitter to the following:
Tube Calibration Number: 1000015010000000
Units: ft/s
Analog Output Range: 20mA = 30.00 ft/s
Analog Output Zero: 4mA = 0 ft/s
Coil Pulse Mode: 6 Hz
2. Set the loop to manual (if necessary).
3. Power down the transmitter.
STEP 2: CONNECT WIRING AND POWER UP
1. Insert one end of the wiring assembly into the 8714D Calibration Standard; wire the
contact end of the wiring assembly to the transmitter. See Figures 1 and 2 on the
following page for detailed instructions regarding 8712D, 8732C, and 8742C.
Rosemount 8712D (Figure 1):
Use the six contact Pin terminal plug-style wiring assembly. Follow the numeric convention
for the 8712D so the plugs match the terminal block.
Rosemount 8732C/8742C (Figure 2):
Use the two black connector-style wiring assembly. (One connector has four contacts, the other
has three.) Remove the electronics side cover (furthest away from the conduit plugs). If you do not
have a LOI, the connectors will be clearly visible on the bottom side of the board.
If you have a LOI, remove the two mounting screws from the LOI assembly and pull the
display assembly away from the connector assembly until the connector assembly on the
back of the board is fully released. Then, plug the calibrator connectors into the appropriate
receptacles.
Figure 1. Rosemount 8712D Terminal Block
1 2
Coil 17 18 19
Electrode
4764_revBA_QIG.fm Page 3 Tuesday, June 22, 2004 1:49 PM
Quick Installation Guide
00825-0100-4764, Rev BA
June 2004
Rosemount 8714D
4
CAUTION
Attempting an electronics trim without a Rosemount 8714D may result in an inaccurate transmitter. It
may also generate a DIGITAL TRIM FAILURE message. If this message appears, no values were
changed in the transmitter. Simply power down the transmitter to clear the message. If the trim was
completed, or no error message was generated, correction requires a Rosemount 8714D.
STEP 3: PERFORM ELECTRONICS TRIM
1. Set the Rosemount 8714D to simulate a flow rate of 30 ft/s.
2. Power up the transmitter with the Rosemount 8714D connected. Allow the electronics 30
minutes to warm-up before reading the flow rate.
3. Read the flow rate. It should be between 29.97 and 30.03 ft/s. If the reading is within this
range, return the transmitter to the original configuration. If the reading is not within this
range, continue to step 8.
4. Initiate an electronics trim with the LOI or HART communicator. The electronics trim
takes about six minutes to complete. No transmitter adjustments are required.
STEP 4: VERIFY ROSEMOUNT 8714D CALIBRATION STANDARD
Guidelines for Checking Series
8714D Magnetic Flowmeter Calibration Standard
The Rosemount 8714D Magnetic Flowmeter Calibration Standard operates in conjunction
with 8712D, 8732C, or 8742C Magnetic Flowmeter Transmitters. This device simulates a
flowtube coil load. It accurately produces a simulated flow signal for the purpose of
transmitter calibration.
Required Equipment
• Current source (output and accuracy: 500mA ±5mA)
• Precision Resistor: measured to 5 significant digits, less than 10 ppm, and > 1 watt
• Nanovoltmeter (Agilent 34420A or equivalent)
Figure 2. Rosemount 8732C/8742C Terminal Block
HART Fast Keys 1, 5
LOI Auxiliary Function
Coil
Connection
(Four-position
connector)
Electrode
Connection
(Three-position
connector)
4764_revBA_QIG.fm Page 4 Tuesday, June 22, 2004 1:49 PM
Quick Installation Guide
00825-0100-4764, Rev BA
June 2004 Rosemount 8714D
5
Limitations
• Current through terminals 1 and 2 shall not exceed 600mA (peak)
• Current through terminals 18 and 19 shall not exceed 5mA.
• Calibration shall occur with the standard set at 30 feet per second.
Procedure
1. Set-up your equipment according to Figure 3.
2. Power up the system.
3. Allow the Rosemount 8714D to warm-up for 30 minutes.
4. Set the input current to terminals 1 and 2 at 500mA.
5. Measure and record the average voltage from terminals 18 and 19 over a five minute
period.
6. Measure and record the average voltage across the 1 ohm resistor.
7. Calculate current with V=IR where R is the resistor value.
8. Divide result from step 5 by step 7 result.
9. Power down the system.
10.Switch the connections 1 and 2 at the Rosemount 8714D calibration standard.
11. Set the input current to terminals 1 and 2 at 500 mA.
12.Measure and record the average voltage from terminals 18 and 19 over a five minute
period.
13.Measure and record the average voltage across the 1 ohm resistor.
14.Calculate current with V=IR where R is the resistor value.
15.Divide result from step 12 by step 14 result.
16.Add the absolute value steps 8 and 15 and divide by two. The value should be within
0.05% (0.00108 mV/Amp) of 2.156mV/Amp.
17.If your device does not operate in conjunction with this specification, return the
Rosemount 8714D to the Rosemount Inc. factory for adjustment.
Figure 3. Set-up Rosemount 8714D and the transmitter as shown
Within the United States, Rosemount Inc. has two toll-free assistance numbers.
Customer Central: 1-800-999-9307
(7:00 a.m. to 7:00 p.m. CST)
Technical support, quoting, and order-related questions.
North American Response Center: 1-800-654-7768
(24 hours a day - Includes Canada) Equipment service needs.
Current
Source
Rosemount
8714D
Voltmeter
1 Ohm
Resistor
Current
Source
18
19
17
1
2
4764_revBA_QIG.fm Page 5 Tuesday, June 22, 2004 1:49 PM
Quick Installation Guide
00825-0100-4764, Rev BA
June 2004
Rosemount 8714D
6
4764_revBA_QIG.fm Page 6 Tuesday, June 22, 2004 1:49 PM
Inhaltsverzeichnis
Andere Rosemount Messgerät Handbücher
Rosemount
Rosemount 3051S Series Bedienungsanleitung
Rosemount
Rosemount 1151DP Bedienungsanleitung
Rosemount
Rosemount 8732C Bedienungsanleitung
Rosemount
Rosemount TankRadar Pro Stücklistenhandbuch
Rosemount
Rosemount 8732 Series Bedienungsanleitung
Rosemount
Rosemount 148 Bedienungsanleitung
Rosemount
Rosemount 5402 Bedienungsanleitung
Rosemount
Rosemount 3051S Series Bedienungsanleitung
Rosemount
Rosemount 1199 Bedienungsanleitung
Rosemount
Rosemount 485 Annubar Bedienungsanleitung
Rosemount
Rosemount 8800D Series Bedienungsanleitung
Rosemount
Rosemount 8712D Series Bedienungsanleitung
Rosemount
Rosemount 702 Bedienungsanleitung
Rosemount
Rosemount 2120 Bedienungsanleitung
Rosemount
Rosemount 890 Bedienungsanleitung
Rosemount
Rosemount 3095FB Bedienungsanleitung
Rosemount
Rosemount 8712E Bedienungsanleitung
Rosemount
Rosemount 405 Bedienungsanleitung
Rosemount
Rosemount Wireless Pressure Gauge Bedienungsanleitung
Rosemount
Rosemount 2081 pH Bedienungsanleitung
