Rosemount 3300 Series Bedienungsanleitung

Step 1: Mount the Transmitter Head/Probe

Step 2: Set Jumpers and Switches

Step 3: Connect the Wiring

Step 4: Configure

Environmental Conditions

Product Certifications

Start

End

Check Process Connections

Confirm Configuration

www.rosemount.com

Quick Installation Guide

00825-0100-4811, Rev GA

October 2011 Rosemount 3300 Series

Guided Wave Radar Level and Interface

Transmitter

Quick Installation Guide

00825-0100-4811, Rev GA

October 2011

Rosemount 3300 Series

Emerson Process

Management

Rosemount Measurement

8200 Market Boulevard

Chanhassen MN 55317 USA

Tel (USA) 

1 800 999 9307

Tel (International) 

+1 952 906 8888

Fax +1 952 949 7001

Emerson Process

Management

Blegistrasse 23

P.O. Box 1046

CH 6341 Baar

Switzerland

Tel +41 (0) 41 768 6111

Fax +41 (0) 41 768 6300

Emerson FZE

P.O.Box 17033

Jebeli Ali Free Zone

Dubai UAE

Tel +971 4 811 8100

Fax +971 4 886 5465

Emerson Process

Management Asia

Pacific Pte Ltd

1 Pandan Crescent

Singapore 128461

Tel +65 6777 8211

Fax +65 6777 0947

Service Support Hotline:

+65 6770 8711

Email:

Enquiries@AP.EmersonProcess.com



This installation guide provides basic guidelines for the Rosemount 3300 Series. Refer to

Rosemount 3300 Series Reference Manual (Document No. 00809-0100-4811) for more

instructions. The manual and this Quick Installation Guide (QIG) are also available

electronically on www.rosemount.com.



Any substitution of non-authorized parts or repair, other than exchanging the complete

transmitter head or probe assembly, may jeopardize safety and is prohibited.

Unauthorized changes to the product are strictly prohibited as they may unintentionally

and unpredictably alter performance and jeopardize safety. Unauthorized changes that

interfere with the integrity of the welds or flanges, such as making additional perforations,

compromise product integrity and safety. Equipment ratings and certifications are no

longer valid on any products that have been damaged or modified without the prior written

permission of Emerson Process Management. Any continued use of product that has

been damaged or modified without prior written authorization is at the customer's sole

risk and expense.

IMPORTANT NOTICE

WARNING



Failure to follow safe installation and service guidelines could result in death or

serious injury

• Make sure only qualified personnel perform installation or service.

• Use the equipment only as specified in this QIG and the Reference Manual. Failure to

do so may impair the protection provided by the equipment.

• Do not perform any services other than thosecontained in this manual unless you are

qualified.

Explosions could result in death or serious injury

• Verify that the operating environment of the transmitter is consistent with the

appropriate hazardous locations specifications. See Product Certifications on page 18

in this Quick Installation Guide.

• In an Explosion-proof/Flameproof installation, do not remove the transmitter covers

when power is applied to the unit.

• Before connecting a HART®-based Communicator in an explosive atmosphere, make

sure the instruments in the loop are installed in accordance with intrinsically safe or

non-incendive field wiring practices.

• To avoid process leaks, only use o-rings designed to seal with the corresponding

flange adapter.

Electrical shock can result in death or serious injury

• Avoid contact with the leads and terminals. High voltage that may be present on leads

can cause electrical shock.

• Make sure the main power to the Rosemount 3300 Series transmitter is off and the

lines to any other external power source are disconnected or not powered while wiring

the transmitter.

Temperature restrictions apply for Explosion-proof versions. For limits, see

certificate-specific information in the Product Certification chapter in this

document.

Quick Installation Guide

00825-0100-4811, Rev GA

October 2011 Rosemount 3300 Series

WARNING



The electronics enclosures are category 2G or 2D equipment. The probes not covered

with plastic and not made of titanium, are category 1G or 1D. The plastic covered probes

or probes made of titanium, are only category 1G equipment.

Probes with non-conducting surfaces and light metals

• Probes covered with plastic and/or with plastic discs may generate an ignition-

capable level of electrostatic charge under certain extreme conditions. Therefore,

when the probe is used in a potentially explosive atmosphere, appropriate measures

must be taken to prevent electrostatic discharge. These probes are not allowed in

dust classified areas.



The following probes do not contain plastic or PTFE material, and are allowed to be

placed in a Dust classified area:

Code Material of Construction:

Process Connection/Probe

1 316L SST (EN 1.4404)

2 Alloy C-276 (UNS N10276)

3 Alloy 400 (UNS N04400)

H Alloy C-276 (UNS N10276)

M Alloy 400 (UNS N04400)

D Duplex process connection



The Material of Construction Code in the above table can be found in the following

position in the Rosemount 3300 Series model code: 330xxxxxN...

Category 2G or 2D Category 2G or 2D

Category 1G or 1D

Probes according to table Category 1G

All probes possible

Applicable

Marking:

II 1/2 G Ex d [ia] IIC T6...T4

II 1/2 D Ex tD [iaD] A21/20 IP6X T85 °C...T135 °C

II 1/2 G Ex d [ia] IIC T6...T4

II -/2 D Ex tD [iaD] A21 IP6X T85 °C...T135 °C

• Probes and flanges containing >7.5% Magnesium or Zirconium are not allowed in

explosive dust atmosphere. Please contact Rosemount Tank Radar for additional

information.

Probes and flanges containing light metals

• When used in category 1/2G installations, probes and flanges containing Titanium or

Zirconium must be mounted in such a way that sparks from impact or friction between

these parts and steel cannot occur.

Quick Installation Guide

00825-0100-4811, Rev GA

October 2011

Rosemount 3300 Series

WARNING

Flange

Probe

Gasket

Tank

Flange

Transmitter

Housing

Nut

Bolt

Quick Installation Guide

00825-0100-4811, Rev GA

October 2011 Rosemount 3300 Series

STEP 1: MOUNT THE TRANSMITTER HEAD/PROBE

Tank Connection with Flange

1. Place a gasket on top of the tank flange.

2. Lower the transmitter and probe with flange into

the tank.

3. Tighten the bolts.

4. Loosen the nut that connects the housing to the

probe and rotate the housing to the desired 

direction.

5. Tighten the nut.

Adapter

Probe

Tank Flange/

Process

Connection

Nut

Sealant on

threads (NPT)

Gasket (BSP/G)

Threaded Tank Connection

1. For adapters with BSP/G threads, place a gasket 

on top of the tank flange.

2. Lower the transmitter and probe into the tank.

3. Mount the adapter into the process connection.

4. Loosen the nut that connects the housing to the 

probe and rotate the housing to the desired 

direction.

5. Tighten the nut.

NOTE

For adapters with NPT threads, pressure-tight

joints require a sealant.

Probe

Tank

Tri-Clamp

Clamp

Gasket

Tri-Clamp Tank Connection

1. Place a gasket on top of the tank flange.

2. Lower the transmitter and probe into the tank.

3. Fasten the Tri-Clamp connection to the tank with a

clamp.

4. Slightly loosen the nut that connects the transmitter

housing to the probe.

5. Rotate the transmitter housing so the cable

entries/display face the desired direction.

6. Tighten the nut.

Refer to Rosemount 3300 Series Reference Manual (Document No. 00809-0100-4811) for

details regarding the mounting of transmitter head/probe.

U-bolts

Bracket

Clamping

brackets

Transmitter

housing

Probe

Bracket

Quick Installation Guide

00825-0100-4811, Rev GA

October 2011

Rosemount 3300 Series

STEP 1 CONTINUED...

Bracket Mounting, on Wall

1. Mount the bracket directly to the wall with screws

suitable for the purpose.

Vertical mounting

Transmitter

housing

Transmitter

housing

Probe

Horizontal mounting

Probe

2. Mount the transmitter with probe to the bracket and

secure the installation with the three supplied

screws.

Bracket Mounting, on Pipe

1. Put the two U-bolts through the holes of the

bracket. Holes are available for both vertical and

horizontal pipe mounting.

2. Put the clamping brackets on the U-bolts and

around the pipe.

3. Fasten the bracket to the pipe using the four

supplied nuts.

4. Mount the transmitter with probe to the bracket and

secure with the three supplied screws.

See the Rosemount 3300 Series Reference Manual

(Document No. 00809-0100-4811) for more

installation details.

M50 nut

Remote Housing

1. Remove the transmitter head from the probe by

unscrewing the M50 nut.

2. Mount the probe in the tank by following the

previous instructions in this section.

U-bolt Bracket Clamping

brackets

M6 screw

3. Mount the bracket to the pole, making sure the

distance between the probe and bracket does not

exceed the length of the remote connection.

• Put the two U-bolts through the holes of the

bracket. Several holes are available for

vertical/horizontal pipe mounting.

• Put the clamping brackets on the U-bolts and

around the pipe.

• Use the supplied nuts to fasten the bracket to

the pipe.

4. Fasten the housing support to the bracket using

the M6 screws. The screws are threaded through

the top of the mounting bracket and into the

housing support.

M50 nut

5. Mount the probe housing on the probe, making

sure that the M50 nut is properly tightened.

6. Connect the transmitter head on the housing

support, making sure that the M50 nut is properly

tightened.

Quick Installation Guide

00825-0100-4811, Rev GA

October 2011 Rosemount 3300 Series

STEP 1 CONTINUED...

Quick Installation Guide

00825-0100-4811, Rev GA

October 2011

Rosemount 3300 Series

STEP 2: SET JUMPERS AND SWITCHES

If alarm and security jumpers are not set, the transmitter operates with the default alarm

condition HIGH and Security OFF. 

Write Protection must be set after configuration (Step 4).



To set Alarm and Write Protection on the circuit board:

1. Remove the cover on the circuit side (see label marked 

circuit side).

2. To set the 4-20 mA alarm output to LOW, move the

alarm switch to the LOW position.

3. To enable the security write protection feature, move 

the write protect switch to the ON position.

4. Replace the cover and tighten securely.

To set Alarm and Write Protection on the LCD:

To have the LCD override the circuit board settings, the write

protection switch needs to be in the OFF position and the alarm

switch needs to be in the HIGH position.

1. To set the 4-20 mA alarm output to LOW, place a 

jumper between the right and center hole position.

2. To enable the security write protection feature, place a 

jumper between the left and center hole position - 

ON.

Quick Installation Guide

00825-0100-4811, Rev GA

October 2011 Rosemount 3300 Series

STEP 3: CONNECT THE WIRING

For HART, the input voltage is 11-42 V (11-30 V in IS applications, 16-42 V in

Explosion-proof / Flameproof applications). For Modbus, the input voltage is 8-30 V.

The transmitter requires shielded twisted pair wiring (18-12 AWG) suitable for the supply

voltage and, if applicable, approved for use in hazardous areas.

Cable/conduit entries

The electronics housing has two entries for ½ - 14 NPT. Optional M20×1.5 and PG 13.5

adapters are also available. The connections are made in accordance with local or plant

electrical codes.

Make sure that unused ports are properly sealed to prevent moisture or other contamination

from entering the terminal block compartment of the electronics housing.

NOTE!

Use the enclosed metal plug to seal the unused port.

Radar Electronics

Dual Compartment Housing

Cable Entry:

½" NPT.

Optional adapters:

M20, PG13.5

Threaded Process

Connections

Flanged Process

Connections

To Connect the Transmitter

1. Make sure the housing is grounded according to Hazardous Locations Certifications,

national and local electrical codes.

2. Verify that the power supply is disconnected.

3. Remove the cover on the terminal side (see label marked field terminals).

4. Pull the cable(s) through the cable gland / conduit. For Explosion-proof / Flameproof

installations, only use cable glands or conduit entry devices certified Explosion-proof or

Flameproof.

5. To connect the wires see the illustrations below.

6. If applicable, use the enclosed metal plug to seal any unused port.

7. Replace the cover and tighten.

8. Tighten the cable gland.

9. Connect the power supply.

Quick Installation Guide

00825-0100-4811, Rev GA

October 2011

Rosemount 3300 Series

STEP 3 CONTINUED...

Non-Intrinsically Safe HART Output and Type n Approvals: Non-Sparking/

Energy Limited Power Supply

Load Resistance 250 

Power Supply

HART

Modem

Field Communicator PC

Rosemount 3300

Series Transmitter

Maximum voltage:

Um=250 V

HART: Un=42.4 V

NOTE

Rosemount 3300 Series Transmitters with Flameproof/Explosion-proof HART Output have a

built-in barrier; no external barrier needed.

Intrinsically Safe HART Output

Power 

Supply RL

250 

Approved

IS Barrier DCS

Rosemount 3300

Series Transmitter

IS Parameters:

Ui=30 V, Ii= 130 mA,

Pi=1 W, Li=Ci=0

HART

Modem

Field Communicator

Andere Handbücher für 3300 Series

Inhaltsverzeichnis

Andere Rosemount Sender Handbücher

Rosemount

Rosemount Oxymitter 5000 Bedienungsanleitung

Rosemount

Rosemount 8712C Bedienungsanleitung

Rosemount

Rosemount 848T Bedienungsanleitung

Rosemount

Rosemount 8732 Series Bedienungsanleitung

Rosemount

Rosemount 1199 Bedienungsanleitung

Rosemount

Rosemount 702 Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Rosemount

Rosemount 2051CF Series Bedienungsanleitung

Rosemount

Rosemount 4088A MultiVariable Bedienungsanleitung

Rosemount

Rosemount 3152 Bedienungsanleitung

Rosemount

Rosemount 248 Bedienungsanleitung

Rosemount

Rosemount 248 Bedienungsanleitung

Rosemount

Rosemount 148 Bedienungsanleitung

Rosemount

Rosemount 248 Bedienungsanleitung

Rosemount

Rosemount 3051SMV Bedienungsanleitung

Rosemount

Rosemount 708 Bedienungsanleitung

Rosemount

Rosemount 2240S Bedienungsanleitung

Rosemount

Rosemount 8732E Bedienungsanleitung

Rosemount

Rosemount 3095MF Series Bedienungsanleitung

Rosemount

Rosemount 3108 Bedienungsanleitung

Rosemount

Rosemount 3144P Bedienungsanleitung

Rosemount

Rosemount 3300 Series Bedienungsanleitung

Rosemount

Rosemount 848T Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung

Excalibur

Excalibur SoundMaster FM Transmitter 144 Bedienungsanleitung